FindChips.com

Reference Designs

• Single Stage 200W AC-DC LLC Series Resonant Conv for 120VAC & 230VAC Input Reference Design - PMP10283 - TI Tool Folder
  PMP10283?SYS-null-null-findchips-refdes-rd-null-wwe: The PMP10283 reference design provides 30V/100W and -30V/100W outputs from AC line voltage to a single LLC resonant converter stage. This design is featured with its low circuit cost and high efficiency (over 90% @ 120VAC full load and ~92% @ 240VAC full load). This design uses the UCC25600 resonant converter controller for LLC resonant converter.
• High Efficiency 350W AC/DC Power Supply Reference Design - PMP11303.2 - TI Tool Folder
  PMP11303: PMP11303 is high-efficiency AC/DC power supply reference design with universal AC input and 25V/13.5A and 12V/1A outputs. LLC+PFC combo IC UCC29950 is applied for the main power stages with 25V/13.5A output while UCC28730 is applied for the auxiliary power with 12V/1A output. This design has low no load power comsumption (152mW@230VAC) and over 93% peak efficiency. This design also meet 80PLUS Gold requirement for 115VAC Internal power supplies.
• Automotive TFT LCD Display Solution - TIDA-00169 - TI Tool Folder
  TIDA-00169?SYS-null-null-findchips-refdes-rd-null-wwe: This reference design implements a video over LVDS solution for automotive infotainment applications.It highlights the support of multi-touch with haptic feedback, LCD backlight control, and ambient light sensing, without the introduction of dedicated support lines back to the host processor. This design is implemented using two boards. The main electronics board, SAT0059 is where the deserializer, microProcessor, backlight controller, haptics drivers and power supply are located. The LCD interface board, SAT0096, is a physical and electrical interface to a specific LCD panel. It connects to the SAT0059 through a Samtec board to board connector and provides connection points for the LCD panel, touchscreen, backlight connections and haptic drivers. The SAT0096 is designed for a Microtips UMSH-8596MD-20T display. If a different display is to be used, a new LCD Interface board would likely need to be designed.
• System Level Power Reference Design for A13 Automotive Wireless Charger Transmitter
  PMP10709: PMP10709 is a system optimized 50 W power designs for A13 Wireless Charger Transmitter used in automotive system. The design has various front end automotive protections such as Load dump through TVS (ISO pulse testing), Reverse Voltage (Through PFET’s body diode), Battery Disconnect Switch with OVP protection (PFET). PMP10709 is primarily four Switch synchronous Buck – Boost design, which supports wide Input voltage range (7V-20V) and delivers any output from 1V-10V based on DAC output of the A13 Wireless Charger. The DAC output changes from 1V to 3.3V which in turn changes the output voltage from 10V to 1V (on the fly) as needed by the algorithm of A13 wireless charger’s transmitter. This design utilizes best in Class Synchronous four Switch Buck Boost Controller LM5175. The design accepts an input voltage of 7Vin to 20Vin and provides the output of 1V- 10V@5 A. Output current never exceeds 5A to protect the charging Coil. The average current regulation loop of the IC at the output is used for this protection.
• 1-kW/36-V Power Stage for Brushless Motor in Battery Powered Garden and Power Tools Reference Design - TIDA-00285 - TI Tool Folder
  TIDA-00285?SYS-null-null-findchips-refdes-rd-null-wwe: This reference design is a power stage for brushless motors in battery-powered garden and power tools rated up to 1 kW. The power stage operates from a 10-cell lithium-ion battery with a voltage range from 36 to 42 V. The design uses CSD18540Q5B NexFETs featuring a very low drain-to-source resistance (RDS_ON ) of 1.8 mΩ in a SON5x6 SMD package, which results in a very small form factor of 57 × 59 mm. The three-phase gate-driver DRV8303 is used to drive the three-phase MOSFET bridge, which can operate from 6 to 60 V and support programmable gate current with maximum setting of 2.3-A sink / 1.7-A source. The power stage can be configured for a single-shunt or three-shunt current sensing. The design supports sensorless control for brushless DC (BLDC) and permanent magnet synchronous motors (PMSM) using trapezoidal control or field oriented control (FOC). The C2000™ Piccolo™ LaunchPad™ is used with the power stage to implement InstaSPIN™-FOC using the motor current and voltage feedback. The corresponding test report evaluates the thermal performance of the board and overcurrent protection features such as cycle-by-cycle control and latch control of the DRV8303.
• Power Reference Design for Xilinx Ultrascale Kintex FPGA Multi-Gigabit Transciever (MGT) with PMBus - PMP9463 - TI Tool Folder
  PMP9463?SYS-null-null-findchips-refdes-rd-null-wwe: The PMP9463 reference design provides all the power supply rails necessary to power the multi-gigabit transcievers (MGT) in Xilinx's Ultrascale™ Kintex® FPGAs. It utilizes a PMBus interface for current and voltage monitoring and meets Xilinx's low output voltage ripple requirement. This design uses a 5V input and offers a low cost discrete solution.
• 2.2MHz Switching, Synchronous Split Supply Reference Design for 12V Battery with all Protections
  PMP10651.4: PMP10651 is a low noise, multi-output SMPS design where LM53603 is used in Inverting Buck-Boost Fly buck topology to generate positive and negative supply needed in multiple noise sensitive applications such as powering High Speed Video Amplifier, RF amplifier, Precision Low noise amplifier etc. The design accepts an input voltage of 7Vin to 15 Vin DC (from 12V Lead Acid Battery) and provides outputs of +12V@500mA, -12v@500mA, 5V @400mA and 3.3V@150mA. It features a small size and is an inexpensive and more efficient solution to using Flyback or Pushpull converters .
• Dual Phase Synchronous Buck - PMP7884 - TI Tool Folder
  PMP7884?SYS-null-null-findchips-refdes-rd-null-wwe: This is a dual-phase, synchronous buck converter with an input voltage range of 30.6V-to-37.4Vin and an output of 9Vout @ 15A.
• 10.8Vin to 13.2Vin; 48Vout @ 7.3A; 4-Phase Synchronous Boost Converter - PMP7944 - TI Tool Folder
  PMP7944?SYS-null-null-findchips-refdes-rd-null-wwe: A 4-phase synchronous boost converter that accepts an input voltage of 10.8Vin to 13.2Vin providing an output of 48Vout capable of delivering 7.3A.
• Automotive low voltage boost stage converts 4V…9Vin to 9Vout@3.3A Reference Design - PMP10130 - TI Tool Folder
  PMP10130?SYS-null-null-findchips-refdes-rd-null-wwe: This small boost converter is meant to increase the output voltage to 9V during cranking phase. Vin = Vout - Vf in nominal conditions. During cranking, the input voltage can reach vaules as low as 4V. Extensive testing with a source generator has been performed.
• Non-Isolated RS-485 to Wi-Fi Bridge with 24 VAC Power Reference Design
  TIDA-00485: The TIDA-00485 TI Design uses Texas Instruments SimpleLink Wi-Fi CC3200 Internet-on-a-chip Wireless MCU module to create a data bridge between an RS-485 network and a Wi-Fi network. An SN65HVD72 transceiver provides the RS-485 Interface with 12 kV of ESD protection, and additional protection is provided on board. The design can be powered with AC or DC power up to 30 V RMS or 48 V peak. A version of this design with an isolated RS-485 interface is presented in TIDA-00486.
• Low Power Flyback with Ultra Wide Input Voltage Range Reference Design
  PMP10098: This reference design has an ultra-wide input voltage range from 19-375V DC / 19-265V AC, and provides an isolated output of 12.0V/40mA. A linear regulator provides a second output of 5.0V/15mA.
• Three Output, 7W, Isolated Fly-back Reference Design
  PMP10866.2: This compact design is intended for use as a 14V bias. It can connect to the secondary side of an LLC and acts as a bias for 2 separate PFCs.
• High Efficiency 200V/520W LLC Series Resonant Converter Reference Design - PMP10949 - TI Tool Folder
  PMP10949?SYS-null-null-findchips-refdes-rd-null-wwe: PMP10949 is a high-efficiency LLC power supply reference design converting from 380VDC input to 200V/2.6A output. 96.7% efficiency is achieved at full load and over 95% efficiency at 150W load.
• 18-48VDC Input, 24V/1A Flyback Reference Design - PMP11047 - TI Tool Folder
  PMP11047?SYS-null-null-findchips-refdes-rd-null-wwe: This reference design provides an isolated 24V/1A output from an 18V-48VDC. The supply is laid out on a small 1.1" by 2.4" circuit board, and achieves over 90% peak efficiency.
• System Level reference design for 30W ADAS system with required Automotive Protections
  PMP10652.5: PMP10652 is a System optimized (CISPR 25 Class 3) 30W design for Surround View ADAS system. The design has various protections such as Load dump through TVS (ISO pulse testing), Reverse Voltage (Innovative Smart diode with very low Iq), Battery Disconnect Switch with OVP protection (PFET) and is EMI optimized to meet Conductive EMI limits of CISPR25 Class3 (overall) and Class5 upto 30MHz Range. Input voltage range is between 4.5V to 30V with OVP at 20V and hence will operate in most Cold Cranking conditions. LM74610 is used for Battery reverse protection which utilizes a charge pump to drive an N-channel FET to provide a resistive path for the bypass current to flow. LM53603Q1 is used as front end DC/DC Buck converter which is 2.2MHz switching, Synchronous rectified Wide Vin Buck Converter which can take transient upto 42V. TPS57114Q1 is used to provide power to the cores and it is a high current 2,2MHz switching buck converter. LM26420 is a dual 2.2MHz switching buck converter which is used for generating other required supplies. LM3880 sequencer is used for all the power up and power down sequencing requirements.
• 2.2MHz Switching, Synchronous Split Supply Reference Design for 12V Battery with all Protections
  PMP10651.1: PMP10651 is a low noise, multi-output SMPS design where LM53603 is used in Inverting Buck-Boost Fly buck topology to generate positive and negative supply needed in multiple noise sensitive applications such as powering High Speed Video Amplifier, RF amplifier, Precision Low noise amplifier etc. The design accepts an input voltage of 7Vin to 15 Vin DC (from 12V Lead Acid Battery) and provides outputs of +12V@500mA, -12v@500mA, 5V @400mA and 3.3V@150mA. It features a small size and is an inexpensive and more efficient solution to using Flyback or Pushpull converters .
• Space-optimized DC/DC Inverting Power Module Reference Design with Minimal BOM Count - TIDA-00808 - TI Tool Folder
  TIDA-00808?SYS-null-null-findchips-refdes-rd-null-wwe: The TIDA-00808 is a simple DC/DC inverting power supply reference design for industrial applications. It takes a wide input voltage between 4.5V and 55V and generates a negative 5V @ 1.75A output with 86% peak efficiency. Since this design is inverting, the maximum output current increases as the input voltage increases. The reference design features the LMZ36002 SIMPLE SWITCHER DC/DC step down power module for compact solution size and simplicity. The board dimension is 76.2 x 76.2 mm (3 x 3 inch) with the solution size of only 30.607 x 20.828 mm (1.205 x 0.82 inch).
• Isolated Flyback Converter for Industrial Bias Supply - Reference Design - PMP7932.1 - TI Tool Folder
  PMP7932: PMP7932 is an isolated flyback converter which accepts an input voltage of 12Vin to 24Vin and provides dual polarity ouputs of +12Vout @ 0.25A and -12V @ 0.25A.
• High Efficiency 410W AC/DC Power Supply Reference Design - PMP11282.2 - TI Tool Folder
  PMP11282: PMP11282 is a high-efficiency AC/DC power supply reference design with universal AC input and 24V/17A output. Interleaved transition mode PFC and LLC series resonant converter is applied for 24V/17A main power. A PSR Flyback with MOSFET integrated controller is applied as the auxiliary supply. 91.98% efficiency is achieved at low line and full load. 94.61% efficiency is achieved at high line and full load.
• RF Sampling 4-GSPS ADC Reference Design with 8-GHz DC-Coupled Differential Amplifier
  TIDA-00431: Wideband radio frequency (RF) receivers allow greatly increased flexibility in radio designs. The wide instantaneous bandwidth allows flexible tuning without changing hardware and the ability to capture multiple channels at widely separated frequencies. This reference design describes a wideband RF receiver utilizing a 4-GSPS analog-to-digital converter (ADC), with an 8-GHz, DC-coupled, fully differential amplifier front end. The amplifier front end provides signal gain and allows capture of signals down to DC, which is not possible with a balun-coupled input.
• 9 to 42Vin 5V/12V/20V @ 5A Synchronous 4-Switch Buck-Boost Converter Reference Design - PMP10698.2 - TI Tool Folder
  PMP10698: PMP10698 is a synchronous 4-switch buck-boost converter which utilizes the LM5175 controller for USB type C applications. The output voltage can be selected for 5V, 12V or 20V at 5A using jumpers or open drain control switches. The LM5175 average current loop sets a maximum output current of 6.25A.
• CISPR 25 Class 5 Rated Multi-Output Power Supply with Pre-Boost for Automotive Cluster Unit
  PMP9477: The PMP9477 design is a conducted EMI optimized multi-output power supply for automotive cluster units. The power supply has a pre-boost stage for cold crank and start-stop operation and two buck regulators. The pre-boost stage features the LM3481 boost controller and will start to operate and regulate a 9.5V output when the input voltage drops below 9.5V. It makes the design a wide input voltage range of 4.5V to 38V suitable for 12V automotive battery systems. The design has two buck regulators following the pre-boost to generate 3 output voltages: the first stage buck generates a 5V, 2A output using the LM26003, and the second stage generates two outputs of 2.8V, 2A and 1.8V, 2A using the LM26420 (the max output power is 15W). The LM26003 is a wide Vin non-synchronous buck regulator, and the LM26420 is a 5V input dual 2A, high frequency synchronous buck regulator. All three ICs are available in automotive grade versions, qualified in AEC-Q100 Grade 1. The board layout is optimized for improved conducted EMI performance. The power inductor in the pre-boost stage is utilized as an input EMI filter, and thus no additional filter components are required. The board is tested under the automotive EMC standard, CISPR 25, and its conducted emissions are in compliance with the CISPR 25 Class 5 requirements.
• 24Vdc Input (Double Car Battery) Automotive Multiphase Sync-Buck Reference Design
  PMP10260: This high-efficiency, high-power reference design uses the LM5119 two-phase synchronous-buck controller to regulate 14.4V at 60A. This design can be used to supply single car battery power from a double battery system, often found in trucks. Features include input EMI filtering, output hot swap protection, input/output current monitoring and temperature monitoring.
• Automotive Buck-boost Converter Providing 8V @ 1.5A Reference Design
  PMP8635: This design is a buck-boost converter for automotive applications covering an input voltage range of 2..20V. It provides an output voltage of 8.0V @ 1.5A continuous / 2.5A peak.
• Automotive Power Supply with Pre-Boost Reference Design
  PMP10223.1: The PMP10223 automotive power reference design provides 5.0V @ 1.1A, 3.3V @ 0.6A and 1.3V at 1.0A. A pre-boost provides 9.0V @ 1.7A to ensure proper operation even during startup of the engine. A synchronous buck converters generates 6.0V @ 2.2A as an intermediate rail for the following buck converters.
• 40W Synchronous ZETA Converter with Two Inductors Reference Design
  PMP9581_REVC: This dual-inductor, 13.2V at 4A, synchronous ZETA converter achieves greater than 93% efficiency at full load. It is capable of 5A out for Vin greater than 10V. It utilizes all surface mount components, maintains a low temperature rise and is capable of high peak load transients. See PMP9581 REVB for this design with a coupled inductor.
• 220W Synchronous 4 Switch Buck-Boost Converter
  PMP9490: PMP9490 is a 225W four Switch Buck –Boost Design utilizing best in Class Synchronous Buck Boost Converter LM5175. The design accepts an input voltage of 9.5Vin to 20Vin and provides the outputs of 15V@15 A for Constant Voltage Output Application such as Voltage stabilizer or as Power amplifier SMPS, 10.8V to 15V@12.5A for CC/CV Battery Charger application, and 12.5 A for Constant Current LED Drive application. It features an inexpensive and more efficient solution to using discrete Buck and boost converters. The average current regulation loop of the IC at the output is used for Battery Charging profiling with no external circuit being involved.
• Wi-Fi System Powered by 2 AA Batteries Extends Life By Using Long Power Off Periods Reference Design - TIDA-00372 - TI Tool Folder
  TIDA-00372?SYS-null-null-findchips-refdes-rd-null-wwe: TIDA-00372 is a power supply design for use with the CC3200 SimpleLink ™ wireless MCU. This design includes a boost power supply that enables the use of analog circuits such as sensor products that cannot operate at voltages available from two series connected AA Batteries. A nano-power timer enables long power-off cycles and increases battery life.
• High Input Voltage Synchronous Buck Provides Two Independent Outputs of 28V at 2A and 16V at 4A - PMP9227 - TI Tool Folder
  PMP9227?SYS-null-null-findchips-refdes-rd-null-wwe: The LM5119 controller allows the user to have two separate regulated outputs or the capability to combine the outputs (of the same voltage) into a two-phase regulator. This design operates from a 36V - 51V input and regulates 28V@2A (with transients up to 7A) and 16V@4A (with transients up to 6A).
• Linear Regulator as a Dynamic Voltage Scaling Power Supply Reference Design
  TIDA-00531: The TIDA-00531 reference design features dynamic voltage scaling (DVS) as a power management solution to power CPU/DSP core voltages.
• 1-kW/36-V Power Stage for Brushless Motor in Battery Powered Garden and Power Tools Reference Design
  TIDA-00285: This reference design is a power stage for brushless motors in battery-powered garden and power tools rated up to 1 kW. The power stage operates from a 10-cell lithium-ion battery with a voltage range from 36 to 42 V. The design uses CSD18540Q5B NexFETs featuring a very low drain-to-source resistance (RDS_ON ) of 1.8 mΩ in a SON5x6 SMD package, which results in a very small form factor of 57 × 59 mm. The three-phase gate-driver DRV8303 is used to drive the three-phase MOSFET bridge, which can operate from 6 to 60 V and support programmable gate current with maximum setting of 2.3-A sink / 1.7-A source. The power stage can be configured for a single-shunt or three-shunt current sensing. The design supports sensorless control for brushless DC (BLDC) and permanent magnet synchronous motors (PMSM) using trapezoidal control or field oriented control (FOC). The C2000™ Piccolo™ LaunchPad™ is used with the power stage to implement InstaSPIN™-FOC using the motor current and voltage feedback. The corresponding test report evaluates the thermal performance of the board and overcurrent protection features such as cycle-by-cycle control and latch control of the DRV8303.
• Four-Output, Flybuck and Buck Converter for High Performance Computing Reference Design - PMP10837.4 - TI Tool Folder
  PMP10837: The PMP10837 reference design offers dual output rails for use in enterprise computing. This design implements an isolated step down design, with non-isolated converters on both the primary and secondary side.
• 432W High-Efficiency Single-Phase Synchronous Buck Converter Reference Design - PMP10509 - TI Tool Folder
  PMP10509?SYS-null-null-findchips-refdes-rd-null-wwe: PMP10509 is a High-Efficiency Single-Phase Synchronous Buck Converter using the LM25117 controller IC. The design accepts an input voltage of 30.4Vin to 33.6Vin (32Vin Nominal) and provides an output of 24Vout capable of supplying 18A of continuous current to the load.
• Two-Switch Buck-Boost Converter for 24W Wide Input
  PMP7995: PMP7995 is a buck-boost converter rated for 12V output at 2A from an input voltage of 5V to 60V. This design uses the LM5118 buck-boost controller at a switching frequency of 300 kHz. To minimize cost the layout was done for a 2 layer printed circuit board.
• Clocking Solution Reference Design for GSPS ADCs - TIDA-00359 - TI Tool Folder
  TIDA-00359?SYS-null-null-findchips-refdes-rd-null-wwe: Low cost, high performance clocking solution for GSPS data converters. This reference design discusses the use of a TRF3765, a low noise frequency synthesizer, generating the sampling clock for a 4 GSPS analog-to-digital converter (ADC12J4000). Experiments demonstrate data sheet comparable SNR and SFDR performance.
• 310W PSU Using Transition Mode Bridgeless PFC and LLC-SRC - Reference Design
  PMP9640: High efficiency, high power factor and reliable power supply are the main focus of the PMP9640 design for motor driver applications. Low cost analog transition mode (TM) PFC controller UCC28051 has been used for bridgeless PFC as the first conversion stage of the PMP9640. LLC series resonant converter (SRC) with UCC25600 is applied as the second stage of the PMP9640. In addition, a high-side buck converter with UCC28710 is applied here as the bias supply. In this design, bridgeless PFC efficiency can go up to 98.5%.
• 192W Dual-Phase Synchronous Boost Converter Reference Design - PMP9403 - TI Tool Folder
  PMP9403?SYS-null-null-findchips-refdes-rd-null-wwe: PMP9403 is a high-efficiency dual-phase synchronous boost converter using the LM5122 controller ICs. The design accepts an input voltage of 9Vin to 15Vin (12Vin Nominal) and provides an output of 48Vout capable of supplying 4A of continuous current to the load.
• 48Vin, 300W 1/8brick Digital Module with GaN FET Reference Design
  PMP4435.2: The PMP4435 is a DC-DC isolated digital module with GaN mosfet reference design targeted for industrial and telecom applications. The DC input range is 36V-60V, with 12V typical and the output is 12V/5A. An digital controller UCD3138A is used in the design. The efficiency is up to 95.8% with good thermal performance.
• Brushless DC Propeller Controller Reference Design - TIDA-00735 - TI Tool Folder
  TIDA-00735?SYS-null-null-findchips-refdes-rd-null-wwe: The TIDA-00735 reference design is a 10.8V to 25.2V brushless DC motor controller for high power propeller, fan, and pump applications. It uses the Texas Instruments' DRV8303 brushless DC motor gate driver, CSD17573Q5B 30V NexFET™ power MOSFETs, MSP430 16-bit low power MCU, and TPS70933 30V ultra-low IQ LDO. It controls motor with trapezoidal sensor-less control algorithm and commands the motor speed through an external reference signal from a central controller. This design is focused on demonstrating a highly efficient and high power BLDC motor system.
• Ten Output QR Flyback and Buck Converter Reference Design
  PMP10822.1: The PMP10822 reference design utilizes two QR flyback, and four buck converters. The efficiency for the 12V and 24V flyback approaches 87%, while the 16V buck converter has efficiency greater than 89%.
• CISPR 25 Class 5 Multi-Output Power Supply Reference Design for Rear Camera, Automotive ADAS Systems - PMP9492.1 - TI Tool Folder
  PMP9492: PMP9492 is a conducted EMI optimized (CISPR 25 Class 5) 9 W Multi output Design for Wide Range Vin automotive ADAS application that supports Cold –Cranking Conditions . The design uses an LM53603 regulator IC (used as Buck), LM26420 (used as dual Buck) and TPS60150 regulator IC (used as Charge pump for 5V output). The design accepts an input voltage of 4.5Vin to 20Vin and provides the outputs of 3.3V @ 1.0A, 2.5V @ 1.0A, 1.8V @ 1.0A, and 5V @ 100mA. It features a small size and is an inexpensive and more efficient solution customized for ADAS and other Automotive related applications. The Board dimension of PMP9492 PCB is 2600mil × 4000mil. Four layer PCB was used for the design.
• Compact Size Dual 2.5A USB Car Charger Reference Design - PMP9402 - TI Tool Folder
  PMP9402?SYS-null-null-findchips-refdes-rd-null-wwe: PMP9402 is a dual USB car charger. This design utilizes the LM3150, TPS2561 Dual Channel Power Switch and a TPS2513 USB Dedicated Charging Port Controller. This design operates from 6 to 40V in. The output is set to 5V; both channels have a 2.5A current limit. This design has a switching frequency of 300 kHz. This design is intended for after-market automotive applications.
• Universal AC Input 5V/10A/50W PSR Flyback Power Supply With Over 89% Avg Efficiency Reference Design - PMP10974 - TI Tool Folder
  PMP10974?SYS-null-null-findchips-refdes-rd-null-wwe: PMP10974 is a quasi-resonant Flyback power suppy based on the UCC28730 primary side regulation (PSR) controller. The elimination of optocoupler using PSR topology promises higher reliability and lower system cost. The design achieves less than 40mW standby power losses and over 89% average efficiency. The design also features UCC2463x synchronous rectification controller.
• Xilinx Virtex Ultrascale FPGA Multi-Gigabit Transceiver (MGT) Power Reference Design with PMBus - PMP9408 - TI Tool Folder
  PMP9408?SYS-null-null-findchips-refdes-rd-null-wwe: The PMP9408 reference design provides all the power supply rails necessary to power the multi-gigabit transcievers (MGT) in Xilinx's Virtex® Ultrascale™ FPGAs. It utilizes a PMBus interface for current and voltage monitoring and meets Xilinx's low output voltage ripple requirement. This design uses a 5V input and offers a low cost discrete solution.
• Universal AC Input, Dual 12V, -8.5V Output Quasi-Resonant Flyback Converter Reference Design
  PMP10150.2: The PMP10150 reference design uses the UCC28600 quasi-resonant flyback controller to generate a 12V and a -8.5V output from an universal AC input. An optocoupler is used to regulate the 12V output.
• High-Efficiency 4 Phase Synchronous Boost Conv for Automotive Trunk Amplifier App Reference Design - PMP7969 - TI Tool Folder
  PMP7969?SYS-null-null-findchips-refdes-rd-null-wwe: PMP7969 is a very high efficiency 4 phase boost controller synchronizable to external clock. Light load efficiency is excellent due to phase shedding capability. Synchronous rectifier also improves efficiency. High effective switching frequency obtained with multiphase over single phase, and current sharing accuracy of ±10%. Bypass mode capable when Vin > Vout.
• Non-Synchronous Boost with Triple Outputs (3.3V@.03A) - PMP7833.3 - TI Tool Folder
  PMP7833: This is a non-synchronous boost converter with an input voltage range of 4.5V-to-5.5Vin and three regulated outputs: 12Vout @ 0.15A, 10.6Vout @ 0.1A, and 3.3Vout @ 0.03A
• Zero drift PGA based Analog Front End Design for Circuit Breakers (ACB/MCCB-ETU) - TIDA-00130 - TI Tool Folder
  TIDA-00130?SYS-null-null-findchips-refdes-rd-null-wwe: This reference design is intended for use in molded case circuit breakers (MCCB) electronic trip units. The programmable gain amplifier based design acts as the current monitoring for over-current earth fault relays. Utilizing a zero drift programmable amplifier, this design provides a ±10 % pick-up (A) accuracy and time delay (s) accuracy of 0 to -20%. Additionally, this solution was designed to handle harsh environment conditions by including features such as ambient insensitivity from -10 to 70 ⁰C and high electromagnetic immunity. Finally the analog front end of this design interfaces seemlessly with the TI MSP430 MCU for quicker evaluation and faster time-to-market.
• High Power Density 12Vin, 100W Synchronous DC/DC Step-Down Buck Converter with Inductor-On-Top
  TIDA-00510.1: The TPS53355 Inductor-On-Top step-down buck converter design enables high power density through reduction of X-Y PCB area by placing the output inductor on top of the IC. This results in 92% minimum efficiency for 66W and 100W output power designs (3.3V and 5V output) requiring only 4x100µF ceramic output caps.
• High-Efficiency Adjustable Output Synchronous Boost Converter Reference Design - PMP10538 - TI Tool Folder
  PMP10538?SYS-null-null-findchips-refdes-rd-null-wwe: PMP10538 is a Single-Phase Synchronous Boost Converter using the LM5122 controller IC. The design accepts an input voltage of 18Vin to 20Vin and provides an output of 30Vout to 54Vout, capable of supplying 1.7A of continuous current to the load or 0A to 3.4A Max. The output voltage can be adjusted between 30Vout and 54Vout by driving the Vadj. input of the Op-Amp circuit between 0V and 3V.
• System Level Power Reference Design for A13 Automotive Wireless Charger Transmitter - PMP10709 - TI Tool Folder
  PMP10709?SYS-null-null-findchips-refdes-rd-null-wwe: PMP10709 is a system optimized 50 W power designs for A13 Wireless Charger Transmitter used in automotive system. The design has various front end automotive protections such as Load dump through TVS (ISO pulse testing), Reverse Voltage (Through PFET’s body diode), Battery Disconnect Switch with OVP protection (PFET). PMP10709 is primarily four Switch synchronous Buck – Boost design, which supports wide Input voltage range (7V-20V) and delivers any output from 1V-10V based on DAC output of the A13 Wireless Charger. The DAC output changes from 1V to 3.3V which in turn changes the output voltage from 10V to 1V (on the fly) as needed by the algorithm of A13 wireless charger’s transmitter. This design utilizes best in Class Synchronous four Switch Buck Boost Controller LM5175. The design accepts an input voltage of 7Vin to 20Vin and provides the output of 1V- 10V@5 A. Output current never exceeds 5A to protect the charging Coil. The average current regulation loop of the IC at the output is used for this protection.
• Automotive Digitally Controlled Boost Power Supply
  TIDA-00282: This TI reference design is an automotive voltage boost converter module. The purpose of this module is to supply a steady voltage to vehicle electronics by boosting during voltage droop events such as engine crank. The design is based on the C2000 Real-Time Microcontroller, and will provide up to 400 Watts of power from a 12V automotive battery system. This solution supports continuous operational input voltage of 6V-16V with protection against 36V load dump to provide a stable 12V output supply with reverse battery protection.
• High Efficiency 15V@1.5A Synchronous Boost Converter Powers Solar Panel Controller Reference Design
  PMP9052: This synchronous boost converter operates from 4.5V to 15V input and achieves a peak efficiency of 99% at full load. Two size options for the inductor allow for high efficiency or reduced size.
• 4-Switch Buck-Boost Delivers High Transient Power for Wireless Base Station Reference Design - PMP9104 - TI Tool Folder
  PMP9104?SYS-null-null-findchips-refdes-rd-null-wwe: This four switch buck-boost converter functions as both a buck or a boost, with a smooth transition between modes. It delivers a 28V (typical) output voltage at 2-3A continuous (4.5A peak) from a 22V-32V input.
• 33W Offline QR Flyback Converter with Multiple Outputs Reference Design
  PMP10020.1: This design uses the UCC28610 quasi-resonant flyback controller to generate 3 isolated outputs from an universal input (90VAC - 290VAC). It was built on a low cost single layer PCB. The regulated output provides 12V@1.89A and the maximum output power is 33W.
• System Level Power Reference Design for 20W ADAS system with Automotive Protections - PMP10750 - TI Tool Folder
  PMP10750?SYS-null-null-findchips-refdes-rd-null-wwe: PMP10750 is a System optimized (CISPR 25 Class 5) 20W design for upstream converter used in ADAS system with automotive protection. The design has various protections such as Load dump through TVS (ISO pulse testing), Reverse Voltage (Innovative Smart diode with very low Iq), Battery Disconnect Switch with OVP protection (PFET) and is EMI optimized to meet Conductive EMI limits of CISPR25 Class5. Input voltage range is between 4.5V to 30V with OVP at 20V and hence will operate in wide input voltage conditions. LM74610 is used for Battery reverse protection which utilizes a charge pump to drive an N-channel FET to provide a resistive path for the bypass current to flow. LM53603Q1 is used as front end DC/DC Buck converter which is 2.2MHz switching, Synchronous rectified Wide Vin Buck Converter which can take transient up to 42V.
• Universal Digital Interface to Absolute Position Encoders Reference Design
  TIDA-00179: The TIDA-00179 reference design is an EMC compliant universal digital interface to connect to absolute position encoders, like EnDat 2.2, BiSS®, SSI or HIPERFACE DSL®. The design supports a wide input voltage range from 15-60V (24V nom). A connector with 3.3V logic I/O signals allows for direct interface to the host processor to run the master protocol. The design allows the host processor to select between a 4-wire encoder interface like EnDat 2.2 and BiSS or a 2-wire interface with power over RS485 like HIPERFACE DSL. To meet the selected encoder's supply range, the design offers a programmable output voltage with either 5.25V or 11V. This design’s power supply offers protection against over-voltage and short circuit according to the selected encoder’s voltage range to prevent damage during a cable short. TIDA-00179 has been tested up to 100m cable length with EnDat 2.2 and 2-wire HIPERFACE DSL encoders.
• High Power Density 12Vin, 12.6W Buck Converter with Integrated Inductor - TIDA-00471 - TI Tool Folder
  TIDA-00471?SYS-null-null-findchips-refdes-rd-null-wwe: The TPS53355 Inductor-On-Top step-down buck converter design enables high power density through reduction of X-Y PCB area and results in >86% efficiency with only 1.8W of power loss and 6mV of output voltage ripple requiring only 5x100uF ceramic output caps.
• 2.2MHz Switching, Synchronous Split Supply Reference Design for 12V Battery with all Protections
  PMP10651.3: PMP10651 is a low noise, multi-output SMPS design where LM53603 is used in Inverting Buck-Boost Fly buck topology to generate positive and negative supply needed in multiple noise sensitive applications such as powering High Speed Video Amplifier, RF amplifier, Precision Low noise amplifier etc. The design accepts an input voltage of 7Vin to 15 Vin DC (from 12V Lead Acid Battery) and provides outputs of +12V@500mA, -12v@500mA, 5V @400mA and 3.3V@150mA. It features a small size and is an inexpensive and more efficient solution to using Flyback or Pushpull converters .
• Hercules Safety MCU Industrial Power Solution Reference Design
  PMP10189.3: This reference design is a complete power solution for the Hercules™ Safety MCU. The input voltage can be in the range of 48..60V and it provides five different output rails with 12.0V @ 30mA, 5.0V @ 240mA, 3.3V @ 620mA, 3.3V @ 230mA and 1.2V @ 700mA.
• Battery Powered Boost Converter Delivers 120Vdc @ 10mA Reference Design - PMP8956 - TI Tool Folder
  PMP8956?SYS-null-null-findchips-refdes-rd-null-wwe: This design is driven by the LM3481. The LM3481 is a versatile Low-Side N-FET high performance controller for switching regulators. The switching frequency of the LM3481 can be adjusted to any value between 100 kHz and 1 MHz by using a single external resistor or by synchronizing it to an external clock. The LM3481 has built in protection features such as thermal shutdown, short-circuit protection and over voltage protection. Power saving shutdown mode reduces the total supply current to 5µA and allows power supply sequencing.
• Quad Output Isolated Synchoronous Fly-Buckboost Converter Reference Design - PMP10545 - TI Tool Folder
  PMP10545?SYS-null-null-findchips-refdes-rd-null-wwe: PMP10545 is an Isolated Flyback Converter with the primary configured as a buck-boost inverter, using the LM5160 regulator IC. The design accepts an input voltage of 9Vin to 30Vin and provides four isolated outputs of +5.7Vout, each capable of supplying 350mA. The design uses an easily available off-the-shelf transformer, making it a more cost effective design solution.
• Ten Output QR Flyback and Buck Converter Reference Design - PMP10822.10 - TI Tool Folder
  PMP10822: The PMP10822 reference design utilizes two QR flyback, and four buck converters. The efficiency for the 12V and 24V flyback approaches 87%, while the 16V buck converter has efficiency greater than 89%.
• CISPR 25 Class 5 Rated Multi-Output Power Supply with Pre-Boost for Automotive Cluster Unit - PMP9477 - TI Tool Folder
  PMP9477?SYS-null-null-findchips-refdes-rd-null-wwe: The PMP9477 design is a conducted EMI optimized multi-output power supply for automotive cluster units. The power supply has a pre-boost stage for cold crank and start-stop operation and two buck regulators. The pre-boost stage features the LM3481 boost controller and will start to operate and regulate a 9.5V output when the input voltage drops below 9.5V. It makes the design a wide input voltage range of 4.5V to 38V suitable for 12V automotive battery systems. The design has two buck regulators following the pre-boost to generate 3 output voltages: the first stage buck generates a 5V, 2A output using the LM26003, and the second stage generates two outputs of 2.8V, 2A and 1.8V, 2A using the LM26420 (the max output power is 15W). The LM26003 is a wide Vin non-synchronous buck regulator, and the LM26420 is a 5V input dual 2A, high frequency synchronous buck regulator. All three ICs are available in automotive grade versions, qualified in AEC-Q100 Grade 1. The board layout is optimized for improved conducted EMI performance. The power inductor in the pre-boost stage is utilized as an input EMI filter, and thus no additional filter components are required. The board is tested under the automotive EMC standard, CISPR 25, and its conducted emissions are in compliance with the CISPR 25 Class 5 requirements.
• 350W PSU with Universal AC Input and 28V Output - Reference Design - PMP9531 - TI Tool Folder
  PMP9531?SYS-null-null-findchips-refdes-rd-null-wwe: High efficiency, high power factor and reliable power supply are the main focus of the PMP9531 design for motor driver applications. Transition mode (TM) power factor correction (PFC) with UCC28051 and LLC series resonant converter (SRC) with UCC25600 are applied in PMP9531. In addition, a high-side buck converter with UCC28710 is applied here as the bias supply. 93% converter efficiency is achieved at high line while still obtaining 90% converter efficiency at low line.
• Isolated Fly-Buck Power Module for PoE Application Reference Design
  PMP10572: The PMP10572 reference design is an single output isolated Fly-Buck power supply for PoE application. It takes 48V nominal input and provides 12V 1A output. The board is designed with TPS2378(PD controller) to provide 40V-57V input votlage and 12V 1SA output power. The design features the LM5160A synchronous buck converter configured as a Fly-Buck regulator. With the benefit of primary side regulation, the supply has the outputs regulated without the opto-coupler or additional transformer winding. The LM5160A has a wide Vin range of 4.5V to 65V and 1.5A output current capability with integrated switch FETs. The input voltage to the reference board can be loosely regulated with a range of 40V to 57V.
• High-Efficiency Low Vin 30W Boost Converter for Automotive Applications (E-Call) Reference Design - PMP9382 - TI Tool Folder
  PMP9382?SYS-null-null-findchips-refdes-rd-null-wwe: PMP9382 is a low Vin boost converter utilizing the automotive grade LM3478Q-Q1 controller. This design starts at a diode drop above the minimum input voltage of 2.97V (~3.4V) to a maximum of 6V in. Once the power supply is enabled and output is present, this design will work down to 2V input minimum, supplying an output voltage of 10V at 3A. The Switching frequency is set to 400 kHz.
• Ten Output QR Flyback and Buck Converter Reference Design
  PMP10822.9: The PMP10822 reference design utilizes two QR flyback, and four buck converters. The efficiency for the 12V and 24V flyback approaches 87%, while the 16V buck converter has efficiency greater than 89%.
• Electric Toothbrush Controller Reference Design - TIDA-00602 - TI Tool Folder
  TIDA-00602?SYS-null-null-findchips-refdes-rd-null-wwe: This TI Design uses Texas Instruments’ low-voltage H-Bridge motor driver with an integrated LDO voltage regulator and an ultra-low-power microcontroller (MCU) to demonstrate a full implementation of a battery powered electric toothbrush.
• Dual Phase Synchronous Buck
  PMP7884: This is a dual-phase, synchronous buck converter with an input voltage range of 30.6V-to-37.4Vin and an output of 9Vout @ 15A.
• 12V/400W Dual-Phase 1/4 Brick Buck Converter Reference Design Delivers 97% Peak Efficiency - PMP7819 - TI Tool Folder
  PMP7819?SYS-null-null-findchips-refdes-rd-null-wwe: This 400W ¼ brick DC/DC converter leverages the LM5119’s dual-phase capability to drive a 33A load in an industry-standard ¼ brick module footprint. This compact design delivers 97% peak efficiency while maintaining balanced current through each phase, which reduces thermal stress and enables lower system cost by eliminating the need to over-design the surrounding power components.
• 36V, 32A Power Stage for BLDC Motor with Cycle by Cycle Stall Current Limiter
  TIDA-00436: This reference design is a power stage for brushless motors in battery-powered garden and power tools rated up to 1 kW, operating from a 10-cell lithium-ion battery with a voltage range from 36 to 42 V. The design uses 60V, N-channel NexFETsTM featuring a very low drain-to-source resistance (RDS_ON ) of 1.8 mΩ in a SON5x6 SMD package, which results in a very small PCB form factor of 57 × 59 mm. The three-phase gate-driver is used to drive a three-phase MOSFET bridge, which can operate from 6 to 60 V and supports programmable gate current with maximum setting of 2.3-A sink / 1.7-A source. The C2000™ Piccolo™ LaunchPad™ LAUNCHXL-F28027 is used along with this power stage and 120 degree trapezoidal control of BLDC motor with Hall sensors is implemented in software. The cycle by cycle current limit feature in the gate-driver protects the board from excessive current that is caused during motor stalls, by limiting the maximum current allowed in the power stage to a safe level.
• System Level reference design for 30W ADAS system with required Automotive Protections - PMP10652.7 - TI Tool Folder
  PMP10652: PMP10652 is a System optimized (CISPR 25 Class 3) 30W design for Surround View ADAS system. The design has various protections such as Load dump through TVS (ISO pulse testing), Reverse Voltage (Innovative Smart diode with very low Iq), Battery Disconnect Switch with OVP protection (PFET) and is EMI optimized to meet Conductive EMI limits of CISPR25 Class3 (overall) and Class5 upto 30MHz Range. Input voltage range is between 4.5V to 30V with OVP at 20V and hence will operate in most Cold Cranking conditions. LM74610 is used for Battery reverse protection which utilizes a charge pump to drive an N-channel FET to provide a resistive path for the bypass current to flow. LM53603Q1 is used as front end DC/DC Buck converter which is 2.2MHz switching, Synchronous rectified Wide Vin Buck Converter which can take transient upto 42V. TPS57114Q1 is used to provide power to the cores and it is a high current 2,2MHz switching buck converter. LM26420 is a dual 2.2MHz switching buck converter which is used for generating other required supplies. LM3880 sequencer is used for all the power up and power down sequencing requirements.
• 6-12V Input to 1.5V/1.5A Output Reference Design with CC/CV Controls - PMP10928 - TI Tool Folder
  PMP10928?SYS-null-null-findchips-refdes-rd-null-wwe: The PMP10928 reference design uses the TPS5402 non-synchronous Buck controller along with INA213 current shunt monitor to achieve CC/CV control for an 1.5V/1.5A output from 6-12V input voltage. +/-5% voltage regulation in CV mode and +/-5% in CC mode is achieved in this design. It is notable that this design allow the output voltage as low as 0.4V in CC mode.
• Wi-Fi System Powered by 2 AA Batteries Extends Life By Using Long Power Off Periods Reference Design
  TIDA-00372: TIDA-00372 is a power supply design for use with the CC3200 SimpleLink ™ wireless MCU. This design includes a boost power supply that enables the use of analog circuits such as sensor products that cannot operate at voltages available from two series connected AA Batteries. A nano-power timer enables long power-off cycles and increases battery life.
• MOSFET Integrated PSR Flyback Reference Design for Universal AC Input and 5V/1.4A Output - PMP10467 - TI Tool Folder
  PMP10467?SYS-null-null-findchips-refdes-rd-null-wwe: The PMP10467 reference design uses the UCC28911 primary-side regulated flyback controller with integrated MOSFET to generate a 5V/1.4A output from an univeral AC input with safety isolation rated transformer on a single layer board. About 50degC temperature rise on UCC28911 is observed at full load. It is notable that the power consumption at no load is less than 40mW.
• 85V - 265V AC in, 12V/3.3A AC/DC Open Frame Power Supply Based on PSR Flyback Reference Design - PMP9576 - TI Tool Folder
  PMP9576?SYS-null-null-findchips-refdes-rd-null-wwe: This reference design provides an isolated 12V/3.3A output from a universal 85V-265V AC input. This design achieves efficiencies greater than 84%. Employing the UCC28710D Primary Side Regulation (PSR) Flyback controller eliminates the opto-coupler and secondary side regulation components. The energy saving features of the UCC28710D allow this design to consume less than 75mW when plugged into the wall with no device attached to the output.
• 40W SEPIC Conv w/Coupled-Inductor Hi Efficiency Operating w/Automotive Input Range Reference Design - PMP9184B - TI Tool Folder
  PMP9184B?SYS-null-null-findchips-refdes-rd-null-wwe: This coupled-inductor 13.2V@3A SEPIC converter achieves 94.5% efficiency. It utilizes all surface mount components, maintains a low temperature rise and is capable of high peak load transients.
• 24V 65W Nominal 130W Surge Offline Flyback Power Supply for Industrial Rails Reference Design - PMP9643 - TI Tool Folder
  PMP9643?SYS-null-null-findchips-refdes-rd-null-wwe: 24V Output, Constant Voltage / Constant Current, 65W Flyback power supply with 130W surge capability. Primary side regulation eliminates feedback opto-coupler and provides 1% regulation down to no-load. Average efficiency of > 89% and no load power of < 70mW are achieved. Voltage input range is 85VAC-265VAC Input.
• Single Supply Analog Input Module Reference Design with 16-Bit, 8-Channel ADC for PLC
  TIPD166: This design is for a 16-bit, 8-channel analog input module for industrial programmable logic controller (PLC) systems. The circuit is realized with an 8-channel, 16-bit, successive-approximation-register (SAR), analog-to-digital converter (ADC) with an integrated precision reference and analog front-end (AFE) circuit.
• Isolated Flyback Converter for Industrial Bias Supply - Reference Design
  PMP7932: PMP7932 is an isolated flyback converter which accepts an input voltage of 12Vin to 24Vin and provides dual polarity ouputs of +12Vout @ 0.25A and -12V @ 0.25A.
• Isolated Flyback Converter for Industrial Bias Supply - Reference Design - PMP7932 - TI Tool Folder
  PMP7932?SYS-null-null-findchips-refdes-rd-null-wwe: PMP7932 is an isolated flyback converter which accepts an input voltage of 12Vin to 24Vin and provides dual polarity ouputs of +12Vout @ 0.25A and -12V @ 0.25A.
• AC Offline Converter Providing 5VDC or 12VDC Output at 2A
  PMP7883.1: The following design, driven by the LM5023, takes an AC input, like the ones located in the common US power outlet, and generates 5V/12V out, 2A DC signal, outputs commonly used for USB connections.
• High Efficiency, 24Vin, Synchronous Buck Converter with PMBus for Industrial Bus POL Applications - PMP11220 - TI Tool Folder
  PMP11220?SYS-null-null-findchips-refdes-rd-null-wwe: The PMP11220 reference design is a high efficiency, high power density, PMBus synchronous buck converter design for programming, and margining the power supply including output voltage. With a nominal input of 24V meant for industrial bus applications, this design allows for programmable output voltages and minimal power loss, all in a small board space. DCAP2 control mode requires no loop compensation, enabling ease of design, while offering ultra-fast load transient response and use with all MLCC output caps.
• Non-Isolated Synchronous Buck used for Transportation and Automotive Applications
  PMP7858: This is a synchronous buck converter with an input voltage range of 8V-to-16Vin (40Vin max) and a regulated output at 5Vout @ 1.5A.
• 200W Natural Interleaving Transition-Mode PFC Flyback LED Driver Reference Design - PMP10116 - TI Tool Folder
  PMP10116?SYS-null-null-findchips-refdes-rd-null-wwe: This design uses the UCC28063A transition-mode pfc controller to drive LEDs up to 700mA current from an AC input. This flyback pfc topology provides isolation and uses quasi-resonant mode control. It supports analog dimming on the output side.
• Automotive TFT LCD Display Solution
  TIDA-00169: This reference design implements a video over LVDS solution for automotive infotainment applications.It highlights the support of multi-touch with haptic feedback, LCD backlight control, and ambient light sensing, without the introduction of dedicated support lines back to the host processor. This design is implemented using two boards. The main electronics board, SAT0059 is where the deserializer, microProcessor, backlight controller, haptics drivers and power supply are located. The LCD interface board, SAT0096, is a physical and electrical interface to a specific LCD panel. It connects to the SAT0059 through a Samtec board to board connector and provides connection points for the LCD panel, touchscreen, backlight connections and haptic drivers. The SAT0096 is designed for a Microtips UMSH-8596MD-20T display. If a different display is to be used, a new LCD Interface board would likely need to be designed.
• 40W Synchronous ZETA Converter with Coupled-Inductor Reference Design
  PMP9581_REVB: This coupled-inductor, 13.2V at 4A, synchronous ZETA converter achieves greater than 95% efficiency at full load. It is capable of 5A out for Vin greater than 10V. It utilizes all surface mount components, maintains a low temperature rise and is capable of high peak load transients. See PMP9581 REVC for this design with seperate inductors.
• 2.2MHz Switching, Synchronous Split Supply Reference Design for 12V Battery with all Protections
  PMP10651.2: PMP10651 is a low noise, multi-output SMPS design where LM53603 is used in Inverting Buck-Boost Fly buck topology to generate positive and negative supply needed in multiple noise sensitive applications such as powering High Speed Video Amplifier, RF amplifier, Precision Low noise amplifier etc. The design accepts an input voltage of 7Vin to 15 Vin DC (from 12V Lead Acid Battery) and provides outputs of +12V@500mA, -12v@500mA, 5V @400mA and 3.3V@150mA. It features a small size and is an inexpensive and more efficient solution to using Flyback or Pushpull converters .
• Xilinx Virtex® UltraScale™ FPGA Multi-Gigabit Transceiver (MGT) Power Solution
  PMP10520.3: The PMP10520 reference design provides all the power supply rails (1V/20A, 1.2V/30A, 1.8V/4A) necessary to power the multi-gigabit transceivers (MGT) in Xilinx's Virtex® UltraScale™ FPGAs. This design uses a 5V input and has a PMBus interface for current and voltage monitoring, margining, timing delays, and fault monitoring. It uses both TPS544C20 and TPS544B20 which feature internal current sensing and eliminate the need for an external current sense resistor. This design also meets Xilinx's low output voltage ripple requirements of the MGT rails.
• Complete Front End Automotive Reverse Polarity and Series Fault Protection Reference Design
  PMP10748: PMP10748 is a complete automotive front end protection TIDesign that highlights TI's zero IQ Smart Diode Controller and High-Side Protection Controller. This design uses two LM74610-Q1 IC's to drive 40V MOSFETs in OR-ing Configuration for reverse polarity protection. The LM74610-Q1 is highly effective zero IQ replacement of lossy diodes and less effective PFET solutions for revere polarity protection. This design also includes programmable OVP, UVLO and OCP with LM5060-Q1 high side protection controller. This device also provides controlled rise time for safe connection and programmable fault detection delay time with LM5060-Q1
• Automotive Emergency Call (eCall) Audio Subsystem Reference Design - TIDA-00724 - TI Tool Folder
  TIDA-00724?SYS-null-null-findchips-refdes-rd-null-wwe: The efficiency and diagnostics necessary for automotive emergency call (eCall) systems generate unique requirements for the audio subsystem, such as speaker diagnostics, and low power consumption. This TI Design shows how to use TI's automotive two-channel audio codec (TLV320AIC3104-Q1) and a class-D audio amplifier (TAS5411-Q1) for eCall applications.
• LP5910 and TPS61221 as Power Reference Design for devices Interacting with Ultra-Low Voltage MSP430 - TIDA-00599 - TI Tool Folder
  TIDA-00599?SYS-null-null-findchips-refdes-rd-null-wwe: The MSP430X09X can operate form ultra-low voltages (ULV) in the range of 0.9V to 1.65V; however most of the devices in the system requires higher voltages. TIDA-00599 provides a solution for those companion devices that requires 1.8V and 3.3V input voltages. A 3.3V voltage rail is generated from a 0.9V to 1.65 V batteries using the TPS61221 boost converter and a 1.8V voltage rail is generated using a high PSRR LDO (LP5910) connected in series with the boost converter output voltage rail. The combine output current is 100 mA at 1.65V input voltage and 50 mA at 0.90 V input voltage. This power solution is deal to power sensors and peripherals from the same ultra-low voltage source powering the MSP430 family line.
• 40W Synchronous ZETA Converter with Two Inductors Reference Design - PMP9581_REVC - TI Tool Folder
  PMP9581_REVC?SYS-null-null-findchips-refdes-rd-null-wwe: This dual-inductor, 13.2V at 4A, synchronous ZETA converter achieves greater than 93% efficiency at full load. It is capable of 5A out for Vin greater than 10V. It utilizes all surface mount components, maintains a low temperature rise and is capable of high peak load transients. See PMP9581 REVB for this design with a coupled inductor.
• High and Wide AC Vin Quasi-Resonant Isolated Flyback Reference Design
  PMP7991.2: PMP7991 is a quasi-resonant isolated flyback using the LM5023 controller IC. The design accepts an input voltage of 85VAC to 265VAC and provides a selectable output of 12Vout or 5Vout capable of supplying 2A of current to the load. The quasi-resonant switching scheme helps to reduce EMI.
• 33W Offline QR Flyback Converter with Multiple Outputs Reference Design - PMP10020 - TI Tool Folder
  PMP10020?SYS-null-null-findchips-refdes-rd-null-wwe: This design uses the UCC28610 quasi-resonant flyback controller to generate 3 isolated outputs from an universal input (90VAC - 290VAC). It was built on a low cost single layer PCB. The regulated output provides 12V@1.89A and the maximum output power is 33W.
• High Efficiency Synchronous Flyback with 36-72Vin to 5Vout@2A Reference Design - PMP8917 - TI Tool Folder
  PMP8917?SYS-null-null-findchips-refdes-rd-null-wwe: PMP8917 has been designed as a competitive open-frame alternative for the communications market with 36-72Vin to 5V/2A. The product is supplied in the industry standard footprint of 2.0 x 1.0 x 0.394 inches. PMP8917 has a basic insulation system from input to output making it suitable for a wide variety of applications. LM5020 is used as synchronous Flyback converter controller for PMP8917 with 92.9% converter efficiency.
• 300W High-Efficiency Single-Phase Synchronous Buck Converter Reference Design
  PMP10514: PMP10514 is a High-Efficiency Single-Phase Synchronous Buck Converter using the LM25117 controller IC. The design accepts an input voltage of 30.4Vin to 33.6Vin (32Vin Nominal) and provides an output of 20 Vout capable of supplying 15A of continuous current to the load.
• Power Reduction Using Dynamic Switching Reference Design - TIDA-00675 - TI Tool Folder
  TIDA-00675?SYS-null-null-findchips-refdes-rd-null-wwe: This design shows the power reduction benefits of dynamically switching a load on/off using a load switch. The design guide shows how frequency of switching, duty cycle, and the use of a discharge resistor can have an impact on power consumption.
• High Power Density 12Vin, 100W Synchronous DC/DC Step-Down Buck Converter with Inductor-On-Top - TIDA-00510.1 - TI Tool Folder
  TIDA-00510: The TPS53355 Inductor-On-Top step-down buck converter design enables high power density through reduction of X-Y PCB area by placing the output inductor on top of the IC. This results in 92% minimum efficiency for 66W and 100W output power designs (3.3V and 5V output) requiring only 4x100µF ceramic output caps.
• High Eff 2Stage Univ Input Power Supply-Transition Mode PFC LLC Resonant Conv Reference Design - PMP8911 - TI Tool Folder
  PMP8911?SYS-null-null-findchips-refdes-rd-null-wwe: Low EMI, high efficiency, high power factor and reliable power supply are main focus of the PMP8911 design for telecom applications. Transient mode (TM) power factor correction (PFC) with UCC28051 and LLC series resonant converter (SRC) with UCC25600 are applied in PMP8911. Low EMI is expected with zero voltage switching on TM-PFC and LLC-SRC switches. An overall 92% efficiency is achieved at 100W full load. In addition, several protections are embedded into this design which includes input under-voltage protection, input over-voltage protection, output over-voltage protection, and output hic-cup over-power protection.
• Universal Line Power Supply for PLC using PSR Flyback and Compact DC/DC Stages Reference Design
  PMP9185.1: The PMP9185 reference design uses the UCC28710 primary-side regulated flyback controller to generate a 15V output from a univeral AC input with maximum 20W output power followied by DC/DC and LDO stages using TPS54229 and TPS650250, and 5V, 3.3V, 1.8V and 1.2V are provided. A switch on the PCB provides the freedom of supplying DC/DC and LDO from AC input or DC input.
• 20W 3-Phase E-Meter Flyback Reference Design
  PMP10129.1: The PMP10129 has been designed especially for E-meters. It uses the LM5021 flyback controller to provide two isolated outputs (6V and 24V) from an 3-phase input. The input voltage range is between 90VAC and 460VAC.
• 60Vin 12Vout @ 4A Buck Reference Design
  PMP9333: The circuit has an operating input voltage range of 50V to 60V max. The output is set at 12V at 4A continuous, with a 7A peak transient.
• 230V AC input to 23V,0.42A Flyback LED Driver - PMP7752 - TI Tool Folder
  PMP7752?SYS-null-null-findchips-refdes-rd-null-wwe: It is a TRAIC dimmable offline flyback LED driver using LM3445. It has an adaptive constant off-time AC/DC constant current controller feature. It can be used with input supply of 230V AC and can light 7 LEDs in string supplying 420mA of current.
• High Efficiency 400W AC/DC Power Supply Reference Design - PMP11064.1 - TI Tool Folder
  PMP11064: PMP11064 is a high-efficiency AC/DC power supply reference design with universal AC input and 20V/20A output. Interleaved transition mode PFC and LLC series resonant converter is applied for 20V/20A main power. A PSR Flyback with MOSFET integrated controller is applied as the auxiliary supply. 91.2% efficiency is achieved at low line and full load. 93.1% efficiency is achieved at high line and full load.
• Automotive low voltage boost stage converts 4V…9Vin to 9Vout@3.3A Reference Design
  PMP10130: This small boost converter is meant to increase the output voltage to 9V during cranking phase. Vin = Vout - Vf in nominal conditions. During cranking, the input voltage can reach vaules as low as 4V. Extensive testing with a source generator has been performed.
• Ten Output QR Flyback and Buck Converter Reference Design
  PMP10822.6: The PMP10822 reference design utilizes two QR flyback, and four buck converters. The efficiency for the 12V and 24V flyback approaches 87%, while the 16V buck converter has efficiency greater than 89%.
• Small Form Factor 12W Ultra Wide Range Power Supply for Protection Relays - Reference Design
  TIDA-00227: This small form factor, 12W power supply solution for protection relays handles an ultra-wide range of both AC and DC inputs making it a suitable platform to power a variety of lower power protection relays that need to be placed in a small housing. The power supply is designed to output industry standard voltages required in protection relays while also providing excellent line and load regulation. This solution has been engineered for high wattage with good efficiency and has also been pre-compliance tested for IEC61000-4 (EFT and Surge) and CISPR 11 Class A (Interference).
• Altera Stratix Vgx Reference Design
  PMP9284: Reference Design for the Stratix Vgx. This design takes into account sequencing needs. Applicable for 25W applications
• Analog Input Module for Industrial Outputs and Temperature Sensors Reference Design - TIPD164 - TI Tool Folder
  TIPD164?SYS-null-null-findchips-refdes-rd-null-wwe: This TI Designs, Precision Verified design implements an analog input module for industrial voltages, currents, and temperature sensors. For industrial outputs, the possible input ranges include: 4-20 mA, 0-20 mA, +/-25 mA, 0-5 V, 0-10 V, +/-5 V, +/-10 V. The design includes conditioning and level-shift circuitry which converts the large industrial outputs into a proper input range for a +5V delta-sigma ADC. The ADC has features to directly acquire information from the RTD and thermocouple sensors over their full temperature range.
• 17.5W Dual USB Car Charger Reference Design
  PMP9367: PMP9367 is a dual USB car charger reference design intended for use in aftermarket automotive application. This design utilizes the LM3150, TPS2561 Dual Channel Power Switch and a TPS2513 USB Dedicated Charging Port Controller. This design operates from 6 to 40V in. The outputs is set to 5V, channel one has a 1A current limit and channel two has a 2.1A current limit. This design has a switching frequency of 300 kHz.
• 50-Ohm 2-GHz Oscilloscope Front-end Reference Design - TIDA-00826 - TI Tool Folder
  TIDA-00826?SYS-null-null-findchips-refdes-rd-null-wwe: This reference design is part of an analog front-end for 50Ω-input oscilloscope application. System designers can readily use this evaluation platform to process input signals from DC to 2 GHz in both frequency-domain and time-domain applications.
• High Power Density 12Vin, 100W Synchronous DC/DC Step-Down Buck Converter with Inductor-On-Top
  TIDA-00510: The TPS53355 Inductor-On-Top step-down buck converter design enables high power density through reduction of X-Y PCB area by placing the output inductor on top of the IC and results in 92% minimum efficiency for 66W and 100W output power designs (3.3V and 5V output) requiring only 4x100µF ceramic output caps.
• Backlight and Smart Lighting Control by Ambient Light and Proximity Sensor Reference Design
  TIDA-00373: This system conserves power and extends backlight life by dynamically adjusting the backlight brightness relative to the environment's ambient light. A capacitive proximity sensor wakes up the system when a user is close to save even more power. This reference design uses the HDC1000. This reference design can also be used with the HDC1008. Watch related videos about Sensing NOW.
• AC Offline Converter Providing 5VDC or 12VDC Output at 2A
  PMP7883.2: The following design, driven by the LM5023, takes an AC input, like the ones located in the common US power outlet, and generates a 5V/12V out, 2A DC signal, an output commonly used for USB connections.
• 48Vin, 300W 1/8brick Digital Module with GaN FET Reference Design - PMP4435.3 - TI Tool Folder
  PMP4435: The PMP4435 is a DC-DC isolated digital module with GaN mosfet reference design targeted for industrial and telecom applications. The DC input range is 36V-60V, with 12V typical and the output is 12V/5A. An digital controller UCD3138A is used in the design. The efficiency is up to 95.8% with good thermal performance.
• 40W SEPIC Conv w/Coupled-Inductor Hi Efficiency Operating w/Automotive Input Range Reference Design
  PMP9184B: This coupled-inductor 13.2V@3A SEPIC converter achieves 94.5% efficiency. It utilizes all surface mount components, maintains a low temperature rise and is capable of high peak load transients.
• 20W 3-Phase E-Meter Flyback Reference Design
  PMP10129.2: The PMP10129 has been designed especially for E-meters. It uses the LM5021 flyback controller to provide two isolated outputs (6V and 24V) from an 3-phase input. The input voltage range is between 90VAC and 460VAC.
• Non-Synchronous Flyback Converter with Dual-Output
  PMP7901: PMP7901 is a Non-Synchronous Flyback converter with an input of 8 volts to 18 volts. It has an Isolated dual-output of 5 volts and negative 5 volts at 0.25 Amps.
• 432W High-Efficiency Single-Phase Synchronous Buck Converter Reference Design
  PMP10509: PMP10509 is a High-Efficiency Single-Phase Synchronous Buck Converter using the LM25117 controller IC. The design accepts an input voltage of 30.4Vin to 33.6Vin (32Vin Nominal) and provides an output of 24Vout capable of supplying 18A of continuous current to the load.
• Triple Output Isolated Fly-Buck Power Supply for Industrial Application Reference Design
  PMP10516: PMP10516 is an Isolated Flybuck Converter using the LM25017 regulator IC. The design accepts an input voltage of 20.4Vin to 28.8Vin (40Vin Max. Peak) and provides three isolated outputs. The +5Vout rail is regulated for precision using the LP2951 linear regulator.
• Reverse Power Supply - Eight Inputs One Output Reference Design - PMP10099 - TI Tool Folder
  PMP10099?SYS-null-null-findchips-refdes-rd-null-wwe: This reference design is a power solution for reverse-powered telecom applications. Up to eight isolated inputs provide one common output; the load is shared equally between all active converters.
• System Level reference design for 30W ADAS system with required Automotive Protections
  PMP10652.2: PMP10652 is a System optimized (CISPR 25 Class 3) 30W design for Surround View ADAS system. The design has various protections such as Load dump through TVS (ISO pulse testing), Reverse Voltage (Innovative Smart diode with very low Iq), Battery Disconnect Switch with OVP protection (PFET) and is EMI optimized to meet Conductive EMI limits of CISPR25 Class3 (overall) and Class5 upto 30MHz Range. Input voltage range is between 4.5V to 30V with OVP at 20V and hence will operate in most Cold Cranking conditions. LM74610 is used for Battery reverse protection which utilizes a charge pump to drive an N-channel FET to provide a resistive path for the bypass current to flow. LM53603Q1 is used as front end DC/DC Buck converter which is 2.2MHz switching, Synchronous rectified Wide Vin Buck Converter which can take transient upto 42V. TPS57114Q1 is used to provide power to the cores and it is a high current 2,2MHz switching buck converter. LM26420 is a dual 2.2MHz switching buck converter which is used for generating other required supplies. LM3880 sequencer is used for all the power up and power down sequencing requirements.
• Sepic with Adjustable Output Voltage and Input Current Limit Reference Design
  PMP10151: This reference design provides an adjustable output voltage between 20V and 25V and an input voltage range of 10V to 14V. It also provides the functionality to limit the input current of the converter between 70mA and 135mA. The adjustable values are set by a VID interface which is either discrete or integrated.
• Automotive Cluster Telltale Driver Reference Design - TIDA-00278 - TI Tool Folder
  TIDA-00278?SYS-null-null-findchips-refdes-rd-null-wwe: This TI reference design is an automotive cluster telltale solution that includes a monolithic, medium-voltage, low-current power 12-bit shift register designed for use in systems that require relatively moderate load power, such as LEDs found in automotive clusters. This design is one part of an entire automotive cluster system solution optimized for the mid-end cluster market. The entire solution supports 4.5-40V system capabilities that can withstand cold crank, start stop, and load dump conditions.
• Power Solution for 450W Automotive Audio Amplifier - PMP7837 - TI Tool Folder
  PMP7837?SYS-null-null-findchips-refdes-rd-null-wwe: The PMP7837 is a 4-phase synchronous boost converter that can take a 6-17V input and put out 24V at 450W. It is used for powering up to eight 50W automotive trunk amplifiers. The 4-phase synchronous design with 450kHz switching frequency per phase results in a compact and efficient circuit well suited for such applications.
• Four-Output, Flybuck and Buck Converter for High Performance Computing Reference Design
  PMP10837.4: The PMP10837 reference design offers dual output rails for use in enterprise computing. This design implements an isolated step down design, with non-isolated converters on both the primary and secondary side.
• Reverse Power Supply - Eight Inputs One Output Reference Design
  PMP10099: This reference design is a power solution for reverse-powered telecom applications. Up to eight isolated inputs provide one common output; the load is shared equally between all active converters.
• Sepic with Adjustable Output Voltage and Input Current Limit Reference Design - PMP10151 - TI Tool Folder
  PMP10151?SYS-null-null-findchips-refdes-rd-null-wwe: This reference design provides an adjustable output voltage between 20V and 25V and an input voltage range of 10V to 14V. It also provides the functionality to limit the input current of the converter between 70mA and 135mA. The adjustable values are set by a VID interface which is either discrete or integrated.
• 144W Single-Phase Synchronous Boost Converter With DCR Current Sensing - PMP9393 - TI Tool Folder
  PMP9393?SYS-null-null-findchips-refdes-rd-null-wwe: PMP9393 is a Single-Phase Synchronous Boost Converter which utilizes the LM5122 controller IC. The design accepts an input voltage of 18Vin to 20Vin and provides an output of 48Vout capable of supplying a maximum of 3A of current to the load. DCR current sensing has been implemented in order to reduce the BOM cost associated with using a high power current sense resistor.
• High Efficiency 350W AC/DC Power Supply Reference Design
  PMP11303.1: PMP11303 is high-efficiency AC/DC power supply reference design with universal AC input and 25V/13.5A and 12V/1A outputs. LLC+PFC combo IC UCC29950 is applied for the main power stages with 25V/13.5A output while UCC28730 is applied for the auxiliary power with 12V/1A output. This design has low no load power comsumption (152mW@230VAC) and over 93% peak efficiency. This design also meet 80PLUS Gold requirement for 115VAC Internal power supplies.
• UART to Wi-Fi Bridge with 24 VAC Power Reference Design - TIDA-00375 - TI Tool Folder
  TIDA-00375?SYS-null-null-findchips-refdes-rd-null-wwe: The TIDA-00375 TI Design uses Texas Instruments SimpleLink Wi-Fi CC3200 Internet-on-a-chip Wireless MCU module to create a data bridge between existing hardware with a logic-level UART interface and a Wi-Fi network. The design also contains a Simple Switcher power supply with a wide input range suitable for 24 volt HVAC systems. The UART interface has buffers to allow this design to interface with equipment that has logic levels between 3.3 volts and 5 volts.
• Single Phase Brushless DC (BLDC) with Brushed Motor Driver Reference Design - TIDA-00875 - TI Tool Folder
  TIDA-00875?SYS-null-null-findchips-refdes-rd-null-wwe: TIDA-00875 demonstrates how to reconfigure existing brushed motor drivers to control single phase brushless (BLDC) motors. The DRV8801 and DRV8701 are used to control a single phase BLDC motor. The DRV8801 design controls the motor at 100% duty cycle. When the device is powered up, the motor runs. The DRV8701 design controls the motor using a PWM input to allow speed control. The designs operates from 12V up to 24V, with full scale current of 2.8A peak (DRV8801) or 20A peak (DRV8701).
• UPOE High-Efficiency Flyback Converter (19V/2.3A) for Forced 4-Pair PoE PD Apps Reference Design
  TIDA-00539: TIDA-00539 uses two TPS2378 PD controllers for a forced 4-pair UPOE solution to 51W non-standard PoE PD applications. It incorportates the UCC2897A controller in a high-efficiency, great transient response (driven) synch flyback converter capble of 19V at 2.3A.
• EN55011 Compliant, Industrial Temperature, 10/100Mbps Ethernet PHY Brick Reference Design - TIDA-00207 - TI Tool Folder
  TIDA-00207?SYS-null-null-findchips-refdes-rd-null-wwe: This Ethernet PHY Brick reference design enables Texas Instruments customers to quickly design systems and release them to market, using TI industrial Ethernet PHY transceiver devices, fully compliant to EN5501 Class A EMI requirements. A 50 Pin Interface has been provided to interface with 32-Bit Cortex M4 processor based Controller board. The board has been designed in a small form factor (2 inches x 3 inches) which makes it easy to fit into existing products. This reference design demonstrates the advanced performance of the DP83848K Ethernet PHY transceiver devices, supports 10/100 Base-T and is compliant with IEEE 802.3 standard. The entire reference design operates from a single power supply (5V with On-Board regulator or 3.3V). All other voltages required for the Ethernet PHY transceiver are internally generated.
• 12V/400W Dual-Phase 1/4 Brick Buck Converter Reference Design Delivers 97% Peak Efficiency
  PMP7819: This 400W ¼ brick DC/DC converter leverages the LM5119’s dual-phase capability to drive a 33A load in an industry-standard ¼ brick module footprint. This compact design delivers 97% peak efficiency while maintaining balanced current through each phase, which reduces thermal stress and enables lower system cost by eliminating the need to over-design the surrounding power components.
• Non-Isolated Synchronous Buck (3.3V@6.4A) - PMP7828.3 - TI Tool Folder
  PMP7828: This is a synchronous buck converter design with an input voltage range of 10.8V-to-13.2Vin and four regulated outputs: 1Vout@24A, 1.5Vout@30A, 3.3Vout@6.4A, and 1.8Vout@8A.
• Single-Supply Strain Gauge in a Bridge Configuration Reference Design - TIPD170 - TI Tool Folder
  TIPD170?SYS-null-null-findchips-refdes-rd-null-wwe: This strain gauge reference design accurately measures the resistance of a strain gauge by being placed in a bridge configuration. The differential voltage of the bridge produced by variation in strain gauge resistance is amplified using the INA333. The bridge excitation voltage and INA333 reference voltage is supplied using the REF5025.
• Dual-Channel Full-Bridge Converter (54V @ 30A) for PoE Power Sourcing (PSE)
  PMP6712: PMP6712 is a phase-shifted full-bridge converter capable of delivering 1600W of isolated output power and achieving efficiency of greater than 96%. This design uses the UCC28950 controller in a dual phase master-slave configuration. An LM5017 constant on-time synchronous buck regulator provides bias power to primary and secondary-side circuits using a coupled inductor with isolated flyback winding. The isolation voltage is specified as 2250VDC, allowing this design to be used as a system supply for Power Over Ethernet and other telecommunications applications.
• 335W Single Stage LLC-SRC Converter Reference Design - PMP10375.2 - TI Tool Folder
  PMP10375: The PMP10375 reference design is a single stage LLC series resonant converter (SRC), producing up to a 335W output using UCC25600 resonant controller. With the use of single stage LLC-SRC, the converter efficiency goes up to 90% at 335W full output power with 120VAC input.
• High Efficiency 15V@1.5A Synchronous Boost Converter Powers Solar Panel Controller Reference Design - PMP9052 - TI Tool Folder
  PMP9052?SYS-null-null-findchips-refdes-rd-null-wwe: This synchronous boost converter operates from 4.5V to 15V input and achieves a peak efficiency of 99% at full load. Two size options for the inductor allow for high efficiency or reduced size.
• SMBus 1- to 4-cell Hybrid Power Boost Mode Battery Charge Controller Reference Design - TIDA-00657 - TI Tool Folder
  TIDA-00657?SYS-null-null-findchips-refdes-rd-null-wwe: The TIDA-00657 reference design enables high efficiency (90+% @1-2A) and faster charge with high charging current up to 3A. The design uses TI's BQ24780 Industrial Innovative Charge Controlller with Hybrid Power Boost Mode and also features power and processor hot monitoring capability.
• Analog Front End for Motor Electronic Overload Relays with Enhanced Current Range - TIDA-00191 - TI Tool Folder
  TIDA-00191?SYS-null-null-findchips-refdes-rd-null-wwe: This reference design is the analog front end (AFE) for an electronic overload relay, used for monitoring and protecting motors from overcurrent or undercurrent events. It is an ideal tool for developers creating overload relays for sensitive AC motors in industrial applications. This programmable gain amplifier (PGA) based analog front end is intended to be an easy evaluation platform for an accurate, industry-leading 10:1 full load ampere (FLA) range and is repeatable over a -10 to +70°C temperature range.
• Integrated 1-3S Standalone Battery Charger with EMI Compliance Reference Design - PMP4397 - TI Tool Folder
  PMP4397?SYS-null-null-findchips-refdes-rd-null-wwe: The PMP4397 is a battery charger module reference design suitable for 2-cell battery applications with a DC input of 4.5V – 15V. Detailed data for radiated emissions compliance is provided. The cell number could be trimmed by resistors over a range from 1-cell to 3-cells. A typical application is for 2-cells (8.4V/2000mAH).
• Electric Toothbrush Controller Reference Design
  TIDA-00602: This TI Design uses Texas Instruments’ low-voltage H-Bridge motor driver with an integrated LDO voltage regulator and an ultra-low-power microcontroller (MCU) to demonstrate a full implementation of a battery powered electric toothbrush.
• Self or Dual-Powered Supply for Protection Relay, MCCBs & ACBs Ref Design - TIDA-00229 - TI Tool Folder
  TIDA-00229?SYS-null-null-findchips-refdes-rd-null-wwe: This power supply solution for Protection Relays & MCCBs handles both the current input from a Current Transformer (CT) or input from an Auxillary (Aux) source. The "self-powered" capability comes from being able to harness the power available in the grid through the CT. The flexibility of this solution's "dual-power" input comes from the ability to also handle the Aux input - which is often a battery source.
• Xilinx Zynq 7000 Series (XC7Z045) 20W Reference Design - PMP10613.2 - TI Tool Folder
  PMP10613: The PMP10613 reference design provides all the power supply rails necessary to power Xilinx® Zynq® 7000 series (XC7Z045) FPGA. This design uses several LMZ3 series modules, LDOs, and a DDR termination regulator to provide all the necessary rails to power the FPGA. It also features one LM3880 for power up and power down sequencing. This design uses a 12V input.
• 7.5Vin to 10Vin; 11.5Vout @ 65A; 4-Phase Synchronous Boost Converter - PMP7937 - TI Tool Folder
  PMP7937?SYS-null-null-findchips-refdes-rd-null-wwe: A 4-phase synchronous boost converter that accepts an input voltage of 7.5Vin to 10Vin and provides an output of 11.5Vout capable of delivering 65A.
• Ultrasonic Water Flow Meter Design using Time to Digital Conversion
  TIDM-ULTRASONIC-FLOW-TDC: The TIDM-ULTRASONIC-FLOW-TDC is a reference design for an ultrasonic flow meter (water, gas or heat meter) with LCD built using a Time-to-Digital converter and an ultra-low power MCU. Solution includes optimized leakage detection, low power consumption, and a small form factor that are important requirements for water, heat and gas meter applications. This design also includes a high efficiency DC-DC converter for system power.
• High-Eff 2Stage Univ Input Pwr Supply Using Trans Mode PFC/LLC Resonant Conv Reference Design
  PMP8920: Low EMI, high efficiency, high power factor and reliable power supply are main focus of the PMP8920 design for telecom applications. Transient mode (TM) power factor correction (PFC) with UCC28051 and LLC series resonant converter (SRC) with UCC25600 are applied in PMP8911. In addition, synchronous rectifier (SR) IC UCC24610 is applied to LLC output rectifier stage. Low EMI is expected with zero voltage switching on TM-PFC and LLC-SRC switches. An overall 91% efficiency is achieved at 100W full load. In addition, several protections are embedded into this design which includes input under-voltage protection, input over-voltage protection, output over-voltage protection, and output hic-cup over-power protection.
• Automotive Digitally Controlled Boost Power Supply - TIDA-00282 - TI Tool Folder
  TIDA-00282?SYS-null-null-findchips-refdes-rd-null-wwe: This TI reference design is an automotive voltage boost converter module. The purpose of this module is to supply a steady voltage to vehicle electronics by boosting during voltage droop events such as engine crank. The design is based on the C2000 Real-Time Microcontroller, and will provide up to 400 Watts of power from a 12V automotive battery system. This solution supports continuous operational input voltage of 6V-16V with protection against 36V load dump to provide a stable 12V output supply with reverse battery protection.
• 20W Industrial Power Supply
  PMP10559: PMP10559 is a non-sync isolated Flybuck-boost converter with a negative primary voltage. The power supply has a synchronous buck regulator, LM5160, and a versa pack transformer. The design accepts an input voltage of 18V to 30V, and outputs 30V, capable of providing 0.67A of current to the load, making it suitable for 24V input industrial application. The Fly-Buck topology can regulate the secondary side outputs without opto-coupler or aux winding, and is capable of achieving good regulation within ±5%. With LM5160's Constan On-Time control, no loop compensation is required, which simplifies the design and helps reducing the external part count and BOM cost.
• TPS92310 Universal 18W
  PMP8006: The main purpose of this reference design is to demonstrate a high efficiency offline LED driver with PFC based on TPS92310. This LED driver is designed for converting an AC input to a regulated LED current.The operating conditions and performance of the reference design are as follows: 1.90VAC to 264VAC, 60/50HZ Input voltage;2.55V to 65V LED Forward Voltage;3.275mA Regulated LED Current;4.System Efficiency ≥ 90%;5.High Power Factor > 0.9;6.Output Short-Circuit and Open-Circuit Protection.
• 6.5V/2A Boost Converter Reference Design
  PMP10026: This reference design provides an output voltage of 6.5V from an input voltage range of 3V to 6.5V.
• BeagleBone Cape for Programmable Logic Controller Reference Design
  TIDA-00312: The BeagleBone Black (BBB) Cape for the PLC I/O module is a platform for evaluation of the PLC I/O reference designs (ex. TIDA-00236). The platform showcases TI’s system solution that can be used in a PLC signal chain and allows evaluation of the signal chain performance. The cape connects the PLC I/O reference design daughter card (ex. TIDA-00236) to the BBB board. The BBB board runs the evaluation software for the I/O card and a webserver, allowing the user to view the performance from a PC. The highlight of this design is the simple hardware and minimal software installation requirements on the PC for evaluation. TI’s PLC I/O module reference designs have complete signal chain for the PLC I/O modules. Evaluating the signal chain requires examination of the critical performance parameters of the hardware. Data collection, processing, and display are the typical functions required for evaluation. The easy-to-use GUI accelerates the performance of the I/O module evaluation process and reduces time to market.
• 12.5Vin to 15.5Vin, 24Vout @ 8A Synchronous Boost Converter Reference Design - PMP9385 - TI Tool Folder
  PMP9385?SYS-null-null-findchips-refdes-rd-null-wwe: PMP9385 is a Single-Phase Synchronous Boost Converter which accepts an input voltage of 12.5Vin to 15.5Vin and provides an output of 24Vout capable of supplying a maximum of 8A of current to the load. Design uses an LM5122 Synchronous Boost controller and CSD18531Q5A FETs.
• Triple Output Isolated Fly-Buck Power Supply for Industrial Application Reference Design
  PMP10516.2: PMP10516 is an Isolated Flybuck Converter using the LM25017 regulator IC. The design accepts an input voltage of 20.4Vin to 28.8Vin (40Vin Max. Peak) and provides three isolated outputs. The +5Vout rail is regulated for precision using the LP2951 linear regulator.
• Reference Design - High Efficiency Two-Phase Synchronous Buck Delivers 300W - PMP9700 - TI Tool Folder
  PMP9700?SYS-null-null-findchips-refdes-rd-null-wwe: This two-phase synchronous buck operates from 24VDC and supplies an output of 15V@20A. Operation at 300KHz (per phase) delivers small size and greater than 96% efficiency.
• Three Output, 7W, Isolated Fly-back Reference Design
  PMP10866.1: This compact design is intended for use as a 14V bias. It can connect to the secondary side of an LLC and acts as a bias for 2 separate PFCs.
• Hercules Safety MCU Industrial Power Solution Reference Design
  PMP10189.4: This reference design is a complete power solution for the Hercules™ Safety MCU. The input voltage can be in the range of 48..60V and it provides five different output rails with 12.0V @ 30mA, 5.0V @ 240mA, 3.3V @ 620mA, 3.3V @ 230mA and 1.2V @ 700mA.
• Backlight and Smart Lighting Control by Ambient Light and Proximity Sensor Reference Design - TIDA-00373 - TI Tool Folder
  TIDA-00373?SYS-null-null-findchips-refdes-rd-null-wwe: This system conserves power and extends backlight life by dynamically adjusting the backlight brightness relative to the environment's ambient light. A capacitive proximity sensor wakes up the system when a user is close to save even more power. This reference design uses the HDC1000. This reference design can also be used with the HDC1008. Watch related videos about Sensing NOW.
• Xilinx Virtex Ultrascale FPGA Multi-Gigabit Transceiver (MGT) Power Reference Design with PMBus - PMP9407 - TI Tool Folder
  PMP9407?SYS-null-null-findchips-refdes-rd-null-wwe: The PMP9407 reference design provides all the power supply rails necessary to power the multi-gigabit transcievers (MGT) in Xilinx's Virtex® Ultrascale™ FPGAs. This design uses a 5V input and has a PMBus interface for current and voltage monitoring, margining, timing delays, and fault monitoring. It uses two TPS544B20's which feature internal current sensing and eliminate the need for an external current sense resistor. This design also meets Xilinx's low output voltage ripple requirements of the MGT rails.
• 8V-40V Input 5V/10A Synchronous Buck for Automotive Applications - PMP7872 - TI Tool Folder
  PMP7872?SYS-null-null-findchips-refdes-rd-null-wwe: PMP7872 is a synchronous buck converter capable of 50W output power. This design uses the LM25117QPSQ emulated current-mode synchronous buck controller and AUIRLR2905Z MOSFETs for automotive applications.
• Noise-immune Capacitive Proximity Sensor System Reference Design - TIDA-00466 - TI Tool Folder
  TIDA-00466?SYS-null-null-findchips-refdes-rd-null-wwe: The FDC2214 proximity and capacitive sensing design demonstrates the use of TI's capacitive sensing technology to sense and detect the presence of various objects. The design is a complete hardware and firmware solution. The firmware processes the data from one proximity sensor and two capacitive touch buttons via the FDC2214 to determine whether an object is in the intended sensing area. Dedicated colored LEDs light up once the device detects a target in close proximity to the board or detects a press on the buttons. The design is powered by one AA-battery.
• Isolated RS-485 to Wi-Fi Bridge with 24 VAC Power Reference Design - TIDA-00486 - TI Tool Folder
  TIDA-00486?SYS-null-null-findchips-refdes-rd-null-wwe: The TIDA-00486 TI Design uses Texas Instruments SimpleLink Wi-Fi CC3200 Internet-on-a-chip Wireless MCU module to create a data bridge between an RS-485 network and a Wi-Fi network. An ISO15 transceiver provides an isolated RS-485 interface with up to 2500 VRMS of isolation. The LM5160 Fly-Buck™ power supply provides both isolated and non-isolated 3.3 V outputs for the two portions of the circuit. The design can be powered with AC or DC power up to 30 VRMS or 48 V peak A version of this design with a non-isolated RS-485 interface is presented in TIDA-00485.
• Power Solution for an Engineering Equipment Fuel Injector - PMP7967 - TI Tool Folder
  PMP7967?SYS-null-null-findchips-refdes-rd-null-wwe: The PMP7967 converts a DC input of 6V-42V to an output of 90V at 1.5A. The design uses four interleaved LM5122 boost controllers with each controller switching at 100kHz. The resulting 4-phase boost converter has a ripple frequency of 400kHz. Freqeucny can also be synchronized to an external signal. Four 330μF aluminum electrolytic capacitors are used at the output to support sudden load current demands in the fuel injector solenoids.
• 12- to 24-V, 27-A Brushed DC Motor Reference Design - TIDA-00620 - TI Tool Folder
  TIDA-00620?SYS-null-null-findchips-refdes-rd-null-wwe: Brushed motors are a relatively popular option for motor designs because of their low price and simple control scheme. A brushed motor has a wire-wound rotor and permanent magnet stator. The commutation of the motor is achieved using conductive rings that are connected to the rotor using brushes that scrape against the commutator rings. This allows the direction of current through the motor to change based on the orientation of the brushes and different commutation rings. Utilizing an H-Bridge allows for easy direction and speed control changes to be applied quickly and efficiently to the brushed DC motor. An electronic drive is required to control the motor currents in a brushed DC motor. The electronic drive circuit consists of a power stage with two-phase inverter meeting the required power capability, a microcontroller to implement the motor speed commands and fault handling, current sensing for motor startup / stall protection, gate driver for controlling the two-phase inverter, and a power supply for microcontroller and other low voltage devices.
• Automotive Power Supply with Pre-Boost Reference Design
  PMP10223.4: The PMP10223 automotive power reference design provides 5.0V @ 1.1A, 3.3V @ 0.6A and 1.3V at 1.0A. A pre-boost provides 9.0V @ 1.7A to ensure proper operation even during startup of the engine. A synchronous buck converters generates 6.0V @ 2.2A as an intermediate rail for the following buck converters.
• 335W Single Stage LLC-SRC Converter Reference Design - PMP10375.1 - TI Tool Folder
  PMP10375: The PMP10375 reference design is a single stage LLC series resonant converter (SRC), producing up to a 335W output using UCC25600 resonant controller. With the use of single stage LLC-SRC, the converter efficiency goes up to 90% at 335W full output power with 120VAC input.
• Automotive Range SEPIC Converter Delivers 12V@1A Reference Design
  PMP8937: This wide input voltage range SEPIC operates from an input of 6V - 48V and produces greater than 89% efficiency. Its compact size and low cost make it idea for automotive and telecom applications.
• Non-Synchronous Boost with Triple Outputs (3.3V@.03A)
  PMP7833.3: This is a non-synchronous boost converter with an input voltage range of 4.5V-to-5.5Vin and three regulated outputs: 12Vout @ 0.15A, 10.6Vout @ 0.1A, and 3.3Vout @ 0.03A
• Non-Isolated Synchronous Buck (1.8V@8A) - PMP7828.4 - TI Tool Folder
  PMP7828: This is a synchronous buck converter design with an input voltage range of 10.8V-to-13.2Vin and four regulated outputs: 1Vout@24A, 1.5Vout@30A, 3.3Vout@6.4A, and 1.8Vout@8A.
• 90 - 134VAc input with isolated Flyback, dual output USB chargers, and LDO Reference Design - PMP10878.2 - TI Tool Folder
  PMP10878: The PMP10878 is an isolated dual port USB charger powered from an AC source. This design allows for up to 36W of power delivery through both USB chargers and the secondary side of a flyback.
• High and Wide AC Vin Quasi-Resonant Isolated Flyback Reference Design
  PMP7991.1: PMP7991 is a quasi-resonant isolated flyback using the LM5023 controller IC. The design accepts an input voltage of 85VAC to 265VAC and provides a selectable output of 12Vout or 5Vout capable of supplying 2A of current to the load. The quasi-resonant switching scheme helps to reduce EMI.
• CISPR 25 Class 5 Rated Multi-Output Power Supply with Pre-Boost for Automotive Cluster Unit - PMP9477.1 - TI Tool Folder
  PMP9477: The PMP9477 design is a conducted EMI optimized multi-output power supply for automotive cluster units. The power supply has a pre-boost stage for cold crank and start-stop operation and two buck regulators. The pre-boost stage features the LM3481 boost controller and will start to operate and regulate a 9.5V output when the input voltage drops below 9.5V. It makes the design a wide input voltage range of 4.5V to 38V suitable for 12V automotive battery systems. The design has two buck regulators following the pre-boost to generate 3 output voltages: the first stage buck generates a 5V, 2A output using the LM26003, and the second stage generates two outputs of 2.8V, 2A and 1.8V, 2A using the LM26420 (the max output power is 15W). The LM26003 is a wide Vin non-synchronous buck regulator, and the LM26420 is a 5V input dual 2A, high frequency synchronous buck regulator. All three ICs are available in automotive grade versions, qualified in AEC-Q100 Grade 1. The board layout is optimized for improved conducted EMI performance. The power inductor in the pre-boost stage is utilized as an input EMI filter, and thus no additional filter components are required. The board is tested under the automotive EMC standard, CISPR 25, and its conducted emissions are in compliance with the CISPR 25 Class 5 requirements.
• CISPR 25 Class 5 Rated 10 W Reference Design for Automotive USB Charger System - PMP9496.2 - TI Tool Folder
  PMP9496: The PMP9496 reference design is a conducted EMI-optimized (CISPR 25 Class 5) 10 W design for efficient automotive USB charger application utilizing the LM53603 regulator IC (2.1MHz fully-integrated synchronous buck for automotive application ) and TPS2549 USB switch(TPS2549-Q1 Automotive USB Charging Port Controller with Integrated Power Switch & Cable Compensation). The design accepts wide input voltage range of 7Vin to 25Vin and provides the outputs of 5V@2.1A. It features a small size and is an inexpensive and more efficient solution customized for automotive USB charger application. The board dimension of the PMP9496 PCB is 2800mil * 4000mil. Four layer PCB was used for the design.
• Universal AC Input, 5V/10A/50W PSR Flyback Power Supply W/Rapid Load Transient Response Ref Design - PMP10407 - TI Tool Folder
  PMP10407?SYS-null-null-findchips-refdes-rd-null-wwe: PMP10407 is a quasi-resonant Flyback power suppy based on the UCC28730 primary side regulation (PSR) controller demonstrating the use of wake up device UCC24650 to achieve rapid load transient response from light load condition when the system is under low frequency operation. The elimination of optocoupler using PSR topology promises higher reliability and lower system cost. The design achieves less than 50mW standby power losses and over 86% efficiency at 25% load. The design also features UCC24610 synchronous rectification controller and demonstrates the use of UCC24650's ENS pin output to enforce diode rectification at light load conditions to reduce stand-by power losses.
• Triple Output Isolated Fly-Buck Power Supply for Industrial Application Reference Design - PMP10516.1 - TI Tool Folder
  PMP10516: PMP10516 is an Isolated Flybuck Converter using the LM25017 regulator IC. The design accepts an input voltage of 20.4Vin to 28.8Vin (40Vin Max. Peak) and provides three isolated outputs. The +5Vout rail is regulated for precision using the LP2951 linear regulator.
• Dual, BDC Motor System with independently controlled motors - TIDA-00116 - TI Tool Folder
  TIDA-00116?SYS-null-null-findchips-refdes-rd-null-wwe: This Mutli-motor BDC motor system implements an MSP430, a DRV8816, and an Anaheim Automation motor. It's suitable for applications requiring 1A to 2A of motor current to 20KRPM. Motor voltage support is 8V to 32V, and max current is 2.5A. The PWM scheme allows speed control and current regulation. The H-bridge FET supports during current decay, the time interval of current decay, and current deglitch time. The motor drive stage has integrated protection from short-circuit, shoot-through, under-voltage, and over-temperature.
• CISPR 22 Class-B Compliant Synchronous Wide Vin Buck Converter Reference Design - PMP9457 - TI Tool Folder
  PMP9457?SYS-null-null-findchips-refdes-rd-null-wwe: This CISPR 22 Class-B compliant reference design features LM46002 in a 75x86mm board size. The synchronous buck regulator, LM46002, is used to generate 3.3V. The input voltage range is 4.5V to 45V and is suitable for 24V industrial supply.
• 30W Isolated Synchronous Flyback Converter Reference Design
  PMP10506: PMP10506 is an isolated synchronous flyback converter using the LM5122 controller IC. The design accepts an input voltage of 9Vin to 60Vin and provides an isolated output of 5Vout capable of supplying 6A of continuous current to the load.
• 36Vin to 60Vin; 15Vout @ 0.05A (Non-Isolated) and 15Vout @ 0.35A (Isolated); Flybuck Converter
  PMP7953.2: A flybuck converter using the LM5017 synchronous buck regulator, which accepts an input voltage of 36Vin to 60Vin and provides two outputs: one non-isolated output of 15Vout capable of supplying 0.05A and an isolated output of 15Vout capable of supplying 0.35A.
• 300-W PFC plus Resonant LLC Half-Bridge controller off-line AC/DC PSU Module - TIDA-00520 - TI Tool Folder
  TIDA-00520?SYS-null-null-findchips-refdes-rd-null-wwe: This is a high efficiency 300-W AC/DC reference design. The design can be biased from external supply or configured for Self-Bias Auxillary mode for operation directly off the AC mains. The PFC is fully internally compensated, reducing design complexity and pcb design. Protections include 3-level OCP, line brown-out, PFC Bulk OVP plus UVP and OTP.
• 14Vin to 15.5Vin, 24Vout @ 8A Synchronous Boost Converter Reference Design
  PMP9386: PMP9385 is a synchronous dual-phase boost converter accepts an input voltage of 14V to 15.5V, and outputs 24V, capable of providing 8A of current to the load.
• Universal Line Power Supply for PLC using PSR Flyback and Compact DC/DC Stages Reference Design - PMP9185.1 - TI Tool Folder
  PMP9185: The PMP9185 reference design uses the UCC28710 primary-side regulated flyback controller to generate a 15V output from a univeral AC input with maximum 20W output power followied by DC/DC and LDO stages using TPS54229 and TPS650250, and 5V, 3.3V, 1.8V and 1.2V are provided. A switch on the PCB provides the freedom of supplying DC/DC and LDO from AC input or DC input.
• Xilinx Kintex UltraScale FPGA Power Solution Reference Design with PMBus - PMP9444 - TI Tool Folder
  PMP9444?SYS-null-null-findchips-refdes-rd-null-wwe: The PMP9444 reference design provides all the power supply rails necessary to power Xilinx's Kintex UltraScale family of FPGAs. It features two UCD90120A's for flexible power up and power down sequencing as well as voltage monitoring, current monitoring, and voltage margining through the PMBus interface. This design uses a 12V input.
• 56W Active Clamp for Telecom Apps Reference Design - PMP10202 - TI Tool Folder
  PMP10202?SYS-null-null-findchips-refdes-rd-null-wwe: This reference design provides 28V out of 48V input voltage to supply noise sensitive loads
• Automotive Power Supply with Pre-Boost Reference Design - PMP10223.2 - TI Tool Folder
  PMP10223: The PMP10223 automotive power reference design provides 5.0V @ 1.1A, 3.3V @ 0.6A and 1.3V at 1.0A. A pre-boost provides 9.0V @ 1.7A to ensure proper operation even during startup of the engine. A synchronous buck converters generates 6.0V @ 2.2A as an intermediate rail for the following buck converters.
• DAC Sample and Hold Glitch Reduction Reference Design
  TIPD142: DAC R-2R architectures display great performance in regards to noise and accuracy, but at a cost of large glitch area. This design focuses on the reduction of major-carry glitches that occur from code specific transitions in DAC R-2R architectures. This design reduces this glitch area, making it suitable for glitch-sensitive applications such as waveform generation.
• 30W Isolated Synchronous Flyback Converter Reference Design - PMP10506 - TI Tool Folder
  PMP10506?SYS-null-null-findchips-refdes-rd-null-wwe: PMP10506 is an isolated synchronous flyback converter using the LM5122 controller IC. The design accepts an input voltage of 9Vin to 60Vin and provides an isolated output of 5Vout capable of supplying 6A of continuous current to the load.
• Small Solution Size Multi Rail Reference Design for Server Line Card - TIDA-00596 - TI Tool Folder
  TIDA-00596?SYS-null-null-findchips-refdes-rd-null-wwe: The TIDA-00596 shows small solution size and high curren density power rails. Supports Internal Sequencing and high output voltage accuracy.
• Ten Output QR Flyback and Buck Converter Reference Design
  PMP10822.10: The PMP10822 reference design utilizes two QR flyback, and four buck converters. The efficiency for the 12V and 24V flyback approaches 87%, while the 16V buck converter has efficiency greater than 89%.
• Small Solution Size Multi Rail Reference Design for Server Line Card
  TIDA-00596: The TIDA-00596 shows small solution size and high curren density power rails. Supports Internal Sequencing and high output voltage accuracy.
• 192W Dual-Phase Synchronous Boost Converter Reference Design
  PMP9403: PMP9403 is a high-efficiency dual-phase synchronous boost converter using the LM5122 controller ICs. The design accepts an input voltage of 9Vin to 15Vin (12Vin Nominal) and provides an output of 48Vout capable of supplying 4A of continuous current to the load.
• TPS92310 - 220VAC, 13W Isolated Flyback LED driver with PFC - PMP8004 - TI Tool Folder
  PMP8004?SYS-null-null-findchips-refdes-rd-null-wwe: The main purpose of this reference design is to demonstrate a high performance offline flyback LED driver with PFC based on TPS92310. This LED driver is designed for converting an AC input to a regulated LED current. The operating conditions and performance of the reference design are as follows: ● 198VAC to 264VAC, 50Hz Input Voltage ● 28V to 34V LED Voltage ● 400mA Regulated LED Current ● 87% Typical System Efficiency ● High Power Factor > 0.9 ● Output Short-Circuit and Open-Circuit Protection
• Hand-to-Hand Body Composition Meter Reference Design with BLE Connectivity
  TIDA-00008: This reference design is for a complete hand-held body composition or fat loss monitor end equipment featuring TI signal chain, power, and connectivity components. With TI's AFE4300 body composition AFE, you can accelerate your body composition design to develop more quickly. This reference design also includes the full BLE connectivity design for easy interface to BLE enabled smartphones, tablets, etc.
• High and Wide AC Vin Quasi-Resonant Isolated Flyback Reference Design - PMP7991.2 - TI Tool Folder
  PMP7991: PMP7991 is a quasi-resonant isolated flyback using the LM5023 controller IC. The design accepts an input voltage of 85VAC to 265VAC and provides a selectable output of 12Vout or 5Vout capable of supplying 2A of current to the load. The quasi-resonant switching scheme helps to reduce EMI.
• 90 - 134VAc input with isolated Flyback, dual output USB chargers, and LDO Reference Design
  PMP10878.3: The PMP10878 is an isolated dual port USB charger powered from an AC source. This design allows for up to 36W of power delivery through both USB chargers and the secondary side of a flyback.
• Ultra-Small 1W, 12V-36V Iso Power Supply for Analog Prog Logic Controller Modules Reference Design
  TIDA-00237: Analog input and output modules are a standard component in Programmable Logic Controllera (PLC) or Distributed Control Systems (DCS). More channels per module and slimmer modules bring design challenges to the isolated power supply in those modules. Anyone facing those challenges will benefit from TIDA-00237, as the total design foot print is less than 2.54x2.54mm and less than 5mm height. It uses a fly-buck approach which means no optocoupler feedback with wide input voltage range of 12V-36V. The design provides +/-15V and 5V isolated, low noise outputs optimal for driving a data converter or analog front end.
• 15W Isolated Downlight / light bulb LED Driver (32V @ 0.4A)
  PMP8011: The main purpose of this reference design is to demonstrate a high performance offline flyback LED driver with PFC based on TPS92314A (220VAC with PFC) . This LED driver is designed for converting an AC input to a regulated LED current. The operating conditions and performance of the reference design are as follows: 198VAC to 264VAC, 50Hz Input Voltage, 28V to 34V LED Voltage, 400mA Regulated LED Current , 87% Typical System Efficiency, High Power Factor > 0.9, Output Short-Circuit and Open-Circuit Protection.
• Analog Front End for Motor Electronic Overload Relays with Enhanced Current Range
  TIDA-00191: This reference design is the analog front end (AFE) for an electronic overload relay, used for monitoring and protecting motors from overcurrent or undercurrent events. It is an ideal tool for developers creating overload relays for sensitive AC motors in industrial applications. This programmable gain amplifier (PGA) based analog front end is intended to be an easy evaluation platform for an accurate, industry-leading 10:1 full load ampere (FLA) range and is repeatable over a -10 to +70°C temperature range.
• Non-Synchronous Flyback converter with dual-output (-5V@.25A) - PMP7901.2 - TI Tool Folder
  PMP7901: PMP7901 is a Non-Synchronous Flyback converter with an input of 8 volts to 18 volts. It has an isolated dual-output of 5 volts and negitive 5 volts at 0.25 Amps.
• 48V Vin Nominal, 100V Vout @ 1A Single-Phase Synchronous Boost Converter
  PMP7933: PMP7933 is a single-phase synchronous boost converter using the LM5122 controller IC. The design accepts an input voltage of 48Vin +/-5% and provides an output voltage of 100Vout capable of supplying a maximum of 1A of current to the load. The design was built on the PMP7896 revB PCB.
• 17.5W Dual USB Car Charger Reference Design - PMP9367 - TI Tool Folder
  PMP9367?SYS-null-null-findchips-refdes-rd-null-wwe: PMP9367 is a dual USB car charger reference design intended for use in aftermarket automotive application. This design utilizes the LM3150, TPS2561 Dual Channel Power Switch and a TPS2513 USB Dedicated Charging Port Controller. This design operates from 6 to 40V in. The outputs is set to 5V, channel one has a 1A current limit and channel two has a 2.1A current limit. This design has a switching frequency of 300 kHz.
• 20W SEPIC Low-Cost Lead Acid Battery Charger Reference Design
  PMP10081: The PMP10081 reference design shows a simple and low-cost solution of a lead acid battery charger. The input voltage range is from 9V to 36V and the maximum output voltage is 13.8V, which is sufficient for a six-cell lead acid battery with a charge current up to 1.5A.
• Automotive Power Supply with Pre-Boost Reference Design
  PMP10223.2: The PMP10223 automotive power reference design provides 5.0V @ 1.1A, 3.3V @ 0.6A and 1.3V at 1.0A. A pre-boost provides 9.0V @ 1.7A to ensure proper operation even during startup of the engine. A synchronous buck converters generates 6.0V @ 2.2A as an intermediate rail for the following buck converters.
• Synchronous Buck Converter for POL DC to DC Module Application Reference Design - PMP9350 - TI Tool Folder
  PMP9350?SYS-null-null-findchips-refdes-rd-null-wwe: PMP9350 is a Constant On-Time synchronous buck regulator utilizing the LM5017 wide-vin with integrated HS and LS MOSFETs for industrial/automotive applications. This board was developed to fit into space-constrained applications. It also uses an external SS circuit for a reduced start-up time.
• TPS92310 - 220VAC, 8W Isolated Flyback LED Driver with PFC
  PMP8005: The main purpose of this reference design is to demonstrate a high performance and compact size offline flyback LED driver with PFC based on TPS92310. This LED driver is designed for converting an AC input to a regulated LED current. The operating conditions and performance of the reference design are as follows: ●198VAC to 264VAC, 50Hz Input Voltage ●18V to 22V LED Voltage ●350mA Regulated LED Current ●84% Typical System Efficiency ●0.9 Typical Power Factor ●Output Short-Circuit and Open-Circuit Protection
• Three Output, 7W, Isolated Fly-back Reference Design
  PMP10866.3: This compact design is intended for use as a 14V bias. It can connect to the secondary side of an LLC and acts as a bias for 2 separate PFCs.
• Positive 12V to -4.35V/15A Buck-Boost Converter Reference Design
  PMP8928: This reference design uses the TPS40170 sync buck controller to generate a -4.35V/15A output from a +12V input voltage. This circuit achieves greater than 94% efficiency at full load.
• Wide Bandwidth Optical Front-end Reference Design
  TIDA-00725: This reference design implements and measures a complete 120MHz wide bandwidth optical front end comprising a high speed transimpedance amplifier, fully differential amplifier, and high speed 14-bit 160MSPS ADC with JESD204B interface. Hardware and software are provided to evaluate the performance of the system in response to high speed optical pulses generated from the included laser driver and diode for applications including optical time domain reflectrometry (OTDR).
• System Level reference design for 30W ADAS system with required Automotive Protections
  PMP10652.6: PMP10652 is a System optimized (CISPR 25 Class 3) 30W design for Surround View ADAS system. The design has various protections such as Load dump through TVS (ISO pulse testing), Reverse Voltage (Innovative Smart diode with very low Iq), Battery Disconnect Switch with OVP protection (PFET) and is EMI optimized to meet Conductive EMI limits of CISPR25 Class3 (overall) and Class5 upto 30MHz Range. Input voltage range is between 4.5V to 30V with OVP at 20V and hence will operate in most Cold Cranking conditions. LM74610 is used for Battery reverse protection which utilizes a charge pump to drive an N-channel FET to provide a resistive path for the bypass current to flow. LM53603Q1 is used as front end DC/DC Buck converter which is 2.2MHz switching, Synchronous rectified Wide Vin Buck Converter which can take transient upto 42V. TPS57114Q1 is used to provide power to the cores and it is a high current 2,2MHz switching buck converter. LM26420 is a dual 2.2MHz switching buck converter which is used for generating other required supplies. LM3880 sequencer is used for all the power up and power down sequencing requirements.
• Highly Integrated Power Reference Design for SSD - TIDA-00719 - TI Tool Folder
  TIDA-00719?SYS-null-null-findchips-refdes-rd-null-wwe: The TIDA-00719 shows small highly integrated power reference solution size for SSD. This reference design supports internal sequencing and high output voltage accuracy.
• 5V/10W Off-Line DCM Flyback Converter Optimized for Zero-Power at No-Load - Reference Design - PMP9561 - TI Tool Folder
  PMP9561?SYS-null-null-findchips-refdes-rd-null-wwe: This design features the UCC28730 flyback controller in conjunction with the UCC24650 wake-up monitor to provide CV, CC regulated output with ultra-low stand-by power that exceeds Level VI and CoC Tier 2 specifications for average efficiency and 10% load efficiency. Wake-up signal detection provides fast transient response to large load steps.
• Automotive Buck-Boost Power Solution Reference Design
  PMP10170: PMP10170 provides a constant output voltage of 5.0V @ 500mA from an wide input voltage range of 4.0V up to 39.0V. It is working with a fixed switching frequency of 380 kHz but provides also the possibility to modulate the switching frequency to reduce the EMI.
• Dual Phase Synchronous Buck (30Vout@10A)
  PMP7885: This is a dual-phase, synchronous buck converter with an input voltage range of 30.6V-to-37.4Vin and providing an output of 30Vout @ 10A.
• Ten Output QR Flyback and Buck Converter Reference Design
  PMP10822.3: The PMP10822 reference design utilizes two QR flyback, and four buck converters. The efficiency for the 12V and 24V flyback approaches 87%, while the 16V buck converter has efficiency greater than 89%.
• 4.5Vin to 5.5Vin; 4Vout @ 0.7A; Flyback
  PMP7964: A Flyback design accepting an input voltage of 4.5Vin to 5.5Vin and providing an isolated output of 4Vout that can deliver 0.7A.
• High Power Density 12Vin, 12.6W Buck Converter with Integrated Inductor
  TIDA-00471: The TPS53355 Inductor-On-Top step-down buck converter design enables high power density through reduction of X-Y PCB area and results in >86% efficiency with only 1.8W of power loss and 6mV of output voltage ripple requiring only 5x100uF ceramic output caps.
• 200W Natural Interleaving Transition-Mode PFC Flyback LED Driver Reference Design
  PMP10116: This design uses the UCC28063A transition-mode pfc controller to drive LEDs up to 700mA current from an AC input. This flyback pfc topology provides isolation and uses quasi-resonant mode control. It supports analog dimming on the output side.
• Ten Output QR Flyback and Buck Converter Reference Design
  PMP10822.8: The PMP10822 reference design utilizes two QR flyback, and four buck converters. The efficiency for the 12V and 24V flyback approaches 87%, while the 16V buck converter has efficiency greater than 89%.
• Non-Isolated Synchronous Buck
  PMP7882: This is a synchronous buck converter with an input voltage range of 10.8V-to-13.2Vin and provinding an output of 1.2Vout @ 3A.
• Non-Isolated Synchronous Buck - PMP7882 - TI Tool Folder
  PMP7882?SYS-null-null-findchips-refdes-rd-null-wwe: This is a synchronous buck converter with an input voltage range of 10.8V-to-13.2Vin and provinding an output of 1.2Vout @ 3A.
• CISPR 25 Class 5 Rated 6.6W Automotive Power Reference Design - PMP9398 - TI Tool Folder
  PMP9398?SYS-null-null-findchips-refdes-rd-null-wwe: The PMP9398 reference design is a conducted EMI optimized 6.6W power supply design for automotive application. It features the SIMPLE SWITCHER® LM46002 synchronous buck regulator and provides a 3.3V, max 2A output. The input voltage range is 4.5V to 60V suitable for 12V automotive battery supply. The reference design has the input EMI filter stage, and the conducted EMI is tested under the CISPR 25 automotive EMC standard. The design is compliant with the Class 5 conducted emissions standard.
• Universal Line Power Supply for PLC using PSR Flyback and Compact DC/DC Stages Reference Design - PMP9185.4 - TI Tool Folder
  PMP9185: The PMP9185 reference design uses the UCC28710 primary-side regulated flyback controller to generate a 15V output from a univeral AC input with maximum 20W output power followied by DC/DC and LDO stages using TPS54229 and TPS650250, and 5V, 3.3V, 1.8V and 1.2V are provided. A switch on the PCB provides the freedom of supplying DC/DC and LDO from AC input or DC input.
• Ten Output QR Flyback and Buck Converter Reference Design
  PMP10822.2: The PMP10822 reference design utilizes two QR flyback, and four buck converters. The efficiency for the 12V and 24V flyback approaches 87%, while the 16V buck converter has efficiency greater than 89%.
• Positive 12V to -4.35V/15A Buck-Boost Converter Reference Design - PMP8928 - TI Tool Folder
  PMP8928?SYS-null-null-findchips-refdes-rd-null-wwe: This reference design uses the TPS40170 sync buck controller to generate a -4.35V/15A output from a +12V input voltage. This circuit achieves greater than 94% efficiency at full load.
• 2.5 A Integrated Sensored BLDC Motor Controller Reference Design - TIDA-00827 - TI Tool Folder
  TIDA-00827?SYS-null-null-findchips-refdes-rd-null-wwe: The TIDA-00827 is an integrated, sensored BLDC motor controller reference design suitable for low-powered, battery operated, brushless DC motor applications. An 8- to 35-V operating voltage range supports 3S to 6S LiPo battery supplies. Specific applications include camera gimbals, low power fans and robotics. The motor controller is composed of the MSP430G2353 16-bit, ultra-low-power microcontroller and the DRV8313 highly integrated, 2.5 A triple half-bridge driver. The MSP430G2353 utilizes Hall sensor-based commutation feedback to provide the correct drive voltages to the motor through the DRV8313. An onboard potentiometer and push button provide a simple interface to control the motor.
• 38V@2A Synchronous Boost Reference Design - PMP10324 - TI Tool Folder
  PMP10324?SYS-null-null-findchips-refdes-rd-null-wwe: The PMP10324 sync-boost reference design provides 38V @ 2A over a wide input range covering the 24V rail. It uses dual external FETs to achieve a full load efficiency of 97% at 24Vin. This design uses minimal footprint parts with all ceramic capacitors.
• Ten Output QR Flyback and Buck Converter Reference Design
  PMP10822.4: The PMP10822 reference design utilizes two QR flyback, and four buck converters. The efficiency for the 12V and 24V flyback approaches 87%, while the 16V buck converter has efficiency greater than 89%.
• Integrated 1-3S Standalone Battery Charger with EMI Compliance Reference Design
  PMP4397: The PMP4397 is a battery charger module reference design suitable for 2-cell battery applications with a DC input of 4.5V – 15V. Detailed data for radiated emissions compliance is provided. The cell number could be trimmed by resistors over a range from 1-cell to 3-cells. A typical application is for 2-cells (8.4V/2000mAH).
• Universal 85VAC-264VAC Input, 24V 1A Output, PSR Flyback Reference Design
  PMP10468: This design uses low-cost primary side regulation (PSR) IC UCC28700 for universal 85VAC-264VAC input range. A 24V output is generated with maximum 24W rating.
• LP5910 and TPS61221 as Power Reference Design for devices Interacting with Ultra-Low Voltage MSP430
  TIDA-00599: The MSP430X09X can operate form ultra-low voltages (ULV) in the range of 0.9V to 1.65V; however most of the devices in the system requires higher voltages. TIDA-00599 provides a solution for those companion devices that requires 1.8V and 3.3V input voltages. A 3.3V voltage rail is generated from a 0.9V to 1.65 V batteries using the TPS61221 boost converter and a 1.8V voltage rail is generated using a high PSRR LDO (LP5910) connected in series with the boost converter output voltage rail. The combine output current is 100 mA at 1.65V input voltage and 50 mA at 0.90 V input voltage. This power solution is deal to power sensors and peripherals from the same ultra-low voltage source powering the MSP430 family line.
• High Density Efficient Solution for Main Aux as well as Back up Aux Power in Drones
  PMP10650.2: PMP10650 is a high power density 40W Buck Converter design optimized for Wide Vin Drone Design using the LM3150 controller IC (Used for Drone’s Backup Power) and LM53603. The design accepts an input voltage of 7Vin to 36Vin and provides the outputs of 5V@5A for Drone’s Backup power and 5V@3A for Drone’s manpower. It features a small size and is an inexpensive and more efficient solution.
• AC Offline Converter Providing 5VDC or 12VDC Output at 2A - PMP7883.2 - TI Tool Folder
  PMP7883: The following design, driven by the LM5023, takes an AC input, like the ones located in the common US power outlet, and generates a 5V/12V out, 2A DC signal, an output commonly used for USB connections.
• 7.5Vin to 10Vin; 11.5Vout @ 65A; 4-Phase Synchronous Boost Converter
  PMP7937: A 4-phase synchronous boost converter that accepts an input voltage of 7.5Vin to 10Vin and provides an output of 11.5Vout capable of delivering 65A.
• Universal Line Power Supply for PLC using PSR Flyback and Compact DC/DC Stages Reference Design
  PMP9185: The PMP9185 reference design uses the UCC28710 primary-side regulated flyback controller to generate a 15V output from a univeral AC input with maximum 20W output power followied by DC/DC and LDO stages using TPS54229 and TPS650250, and 5V, 3.3V, 1.8V and 1.2V are provided. A switch on the PCB provides the freedom of supplying DC/DC and LDO from AC input or DC input.
• 9 to 42Vin 5V/12V/20V @ 5A Synchronous 4-Switch Buck-Boost Converter Reference Design - PMP10698.3 - TI Tool Folder
  PMP10698: PMP10698 is a synchronous 4-switch buck-boost converter which utilizes the LM5175 controller for USB type C applications. The output voltage can be selected for 5V, 12V or 20V at 5A using jumpers or open drain control switches. The LM5175 average current loop sets a maximum output current of 6.25A.
• EN55011 Compliant, Industrial Temperature, 10/100Mbps Ethernet PHY Brick Reference Design
  TIDA-00207: This Ethernet PHY Brick reference design enables Texas Instruments customers to quickly design systems and release them to market, using TI industrial Ethernet PHY transceiver devices, fully compliant to EN5501 Class A EMI requirements. A 50 Pin Interface has been provided to interface with 32-Bit Cortex M4 processor based Controller board. The board has been designed in a small form factor (2 inches x 3 inches) which makes it easy to fit into existing products. This reference design demonstrates the advanced performance of the DP83848K Ethernet PHY transceiver devices, supports 10/100 Base-T and is compliant with IEEE 802.3 standard. The entire reference design operates from a single power supply (5V with On-Board regulator or 3.3V). All other voltages required for the Ethernet PHY transceiver are internally generated.
• Zero drift PGA based Analog Front End Design for Circuit Breakers (ACB/MCCB-ETU)
  TIDA-00130: This reference design is intended for use in molded case circuit breakers (MCCB) electronic trip units. The programmable gain amplifier based design acts as the current monitoring for over-current earth fault relays. Utilizing a zero drift programmable amplifier, this design provides a ±10 % pick-up (A) accuracy and time delay (s) accuracy of 0 to -20%. Additionally, this solution was designed to handle harsh environment conditions by including features such as ambient insensitivity from -10 to 70 ⁰C and high electromagnetic immunity. Finally the analog front end of this design interfaces seemlessly with the TI MSP430 MCU for quicker evaluation and faster time-to-market.
• Non-Isolated Synchronous Buck (3.3V@6.4A)
  PMP7828.3: This is a synchronous buck converter design with an input voltage range of 10.8V-to-13.2Vin and four regulated outputs: 1Vout@24A, 1.5Vout@30A, 3.3Vout@6.4A, and 1.8Vout@8A.
• 20W SEPIC Low-Cost Lead Acid Battery Charger Reference Design - PMP10081 - TI Tool Folder
  PMP10081?SYS-null-null-findchips-refdes-rd-null-wwe: The PMP10081 reference design shows a simple and low-cost solution of a lead acid battery charger. The input voltage range is from 9V to 36V and the maximum output voltage is 13.8V, which is sufficient for a six-cell lead acid battery with a charge current up to 1.5A.
• System Level reference design for 30W ADAS system with required Automotive Protections - PMP10652.2 - TI Tool Folder
  PMP10652: PMP10652 is a System optimized (CISPR 25 Class 3) 30W design for Surround View ADAS system. The design has various protections such as Load dump through TVS (ISO pulse testing), Reverse Voltage (Innovative Smart diode with very low Iq), Battery Disconnect Switch with OVP protection (PFET) and is EMI optimized to meet Conductive EMI limits of CISPR25 Class3 (overall) and Class5 upto 30MHz Range. Input voltage range is between 4.5V to 30V with OVP at 20V and hence will operate in most Cold Cranking conditions. LM74610 is used for Battery reverse protection which utilizes a charge pump to drive an N-channel FET to provide a resistive path for the bypass current to flow. LM53603Q1 is used as front end DC/DC Buck converter which is 2.2MHz switching, Synchronous rectified Wide Vin Buck Converter which can take transient upto 42V. TPS57114Q1 is used to provide power to the cores and it is a high current 2,2MHz switching buck converter. LM26420 is a dual 2.2MHz switching buck converter which is used for generating other required supplies. LM3880 sequencer is used for all the power up and power down sequencing requirements.
• Xilinx Virtex Ultrascale FPGA Multi-Gigabit Transceiver (MGT) Power Reference Design with PMBus
  PMP9408: The PMP9408 reference design provides all the power supply rails necessary to power the multi-gigabit transcievers (MGT) in Xilinx's Virtex® Ultrascale™ FPGAs. It utilizes a PMBus interface for current and voltage monitoring and meets Xilinx's low output voltage ripple requirement. This design uses a 5V input and offers a low cost discrete solution.
• Class 3, COT Buck Converter for PoE Application Reference Design - PMP9416 - TI Tool Folder
  PMP9416?SYS-null-null-findchips-refdes-rd-null-wwe: The PMP9416 reference design is a single output non-isolated buck power supply for PoE applications. It accepts a 48V nominal input and provides a 5V 1A output. The input can be varied from 33V to 57V. The design features the LM5160 synchronous buck converter with the benefit of diode emulated mode which can improve the light load efficiency as compared to FPWM (forced pulse width modulation) mode. The LM5160’s integrated MOSFETs and constant on time control minimize the external component count and enables a small power dense layout.
• Indoor Light Energy Harvesting Reference Design for Bluetooth Low Energy (BLE) Beacon Subsystem
  TIDA-00100: The Indoor Light Energy Harvesting Reference Design for Bluetooth Low Energy (BLE) Beacon Subsystem provides a solution where by with just the power of the typical indoor lighting in a retail environment (greater than 250 LUX) the Bluetooth Low Energy chip can broadcast BLE beacons. This subsystem reference design is highly differentiated over existing solutions as it incorporates no batteries, thus eliminating the hassle of battery replacement, battery charging, and saving costs associated with battery maintenance. This solution also ensures that there are no constraints around installation as long as there is typical indoor lighting available. There is also no ON/OFF switch; the entire load connection and disconnection is handled by the power management IC therefore ensuring that the solution is self managing.
• 36Vin to 60Vin; 15Vout @ 0.05A (Non-Isolated) and 15Vout @ 0.35A (Isolated); Flybuck Converter - PMP7953.1 - TI Tool Folder
  PMP7953: A flybuck converter using the LM5017 synchronous buck regulator, which accepts an input voltage of 36Vin to 60Vin and provides two outputs: one non-isolated output of 15Vout capable of supplying 0.05A and an isolated output of 15Vout capable of supplying 0.35A.
• 24-V, 50-W BLDC Motor Sinusoidal Drive Reference Design for Air Purifier Fans
  TIDA-00656: The TIDA-00656 reference design is a cost-effective, small form-factor (SFF), three-phase sinusoidal motor drive for brushless DC (BLDC) motor up to a power of 50 W at 24 V. The board accepts 24 V at the input and provides three motor outputs to drive the BLDC motor sinusoidally. By using a microcontroller (MCU), in this case the MSP430G2303, the speed loop is closed externally after accepting the speed command over IR (infra-red) sensor.
• High Fidelity 175W Class-D Audio Amplifier with Digital Inputs and Processing Reference Design - TIDA-00874 - TI Tool Folder
  TIDA-00874?SYS-null-null-findchips-refdes-rd-null-wwe: This design turns the extremely high performance analog input TPA3251D2 Class-D amplifier into a digital input system with audio processing using the highly versatile PCM5242 differential output DAC. Now the full performance of TPA3251D2 amplifier can be realized with a variety of digital input sources. The analog differential output and high SNR of the PCM5242 DAC is a perfect match to the fully differential analog input of the TPA3251D2 amplifier achieving outstanding noise performance and extremely low distortion. With the miniDSP on the PCM5242, audio processing and filtering can be added to further enhance audio performance in the end equipment.
• Hand-to-Hand Body Composition Meter Reference Design with BLE Connectivity - TIDA-00008 - TI Tool Folder
  TIDA-00008?SYS-null-null-findchips-refdes-rd-null-wwe: This reference design is for a complete hand-held body composition or fat loss monitor end equipment featuring TI signal chain, power, and connectivity components. With TI's AFE4300 body composition AFE, you can accelerate your body composition design to develop more quickly. This reference design also includes the full BLE connectivity design for easy interface to BLE enabled smartphones, tablets, etc.
• 860W Dual Phase Synchronous Buck Converter in Quarter Brick Footprint
  PMP9260: PMP9260 is a dual-phase synchronous buck converter utilizing the LM5119 dual synchronous buck controller I.C. The design accepts an input voltage of 33V to 60V and provides a 28V output capable of supplying 30A of current to the load. This represents a maximum power density design of 860W in a quarter brick footprint. The maximum component height is set by the Coilcraft VER2923-103 inductors at 0.875 in.
• Two-switch buck-boost converter with 28.0V @ 2.5A and an input voltage range of 10..32V - PMP8570 - TI Tool Folder
  PMP8570?SYS-null-null-findchips-refdes-rd-null-wwe: This design is a two-switch buck boost converter which generates an output voltage of 28.0V @ 2.5A from an input voltage range of 10..32V.
• CISPR 25 Class 5 Rated Multi-Output Power Supply with Pre-Boost for Automotive Cluster Unit
  PMP9477.2: The PMP9477 design is a conducted EMI optimized multi-output power supply for automotive cluster units. The power supply has a pre-boost stage for cold crank and start-stop operation and two buck regulators. The pre-boost stage features the LM3481 boost controller and will start to operate and regulate a 9.5V output when the input voltage drops below 9.5V. It makes the design a wide input voltage range of 4.5V to 38V suitable for 12V automotive battery systems. The design has two buck regulators following the pre-boost to generate 3 output voltages: the first stage buck generates a 5V, 2A output using the LM26003, and the second stage generates two outputs of 2.8V, 2A and 1.8V, 2A using the LM26420 (the max output power is 15W). The LM26003 is a wide Vin non-synchronous buck regulator, and the LM26420 is a 5V input dual 2A, high frequency synchronous buck regulator. All three ICs are available in automotive grade versions, qualified in AEC-Q100 Grade 1. The board layout is optimized for improved conducted EMI performance. The power inductor in the pre-boost stage is utilized as an input EMI filter, and thus no additional filter components are required. The board is tested under the automotive EMC standard, CISPR 25, and its conducted emissions are in compliance with the CISPR 25 Class 5 requirements. As seen at APEC
• Universal AC Input, Dual 12V, -8.5V Output Quasi-Resonant Flyback Converter Reference Design - PMP10150.2 - TI Tool Folder
  PMP10150: The PMP10150 reference design uses the UCC28600 quasi-resonant flyback controller to generate a 12V and a -8.5V output from an universal AC input. An optocoupler is used to regulate the 12V output.
• 36V, 32A Power Stage for BLDC Motor with Cycle by Cycle Stall Current Limiter - TIDA-00436 - TI Tool Folder
  TIDA-00436?SYS-null-null-findchips-refdes-rd-null-wwe: This reference design is a power stage for brushless motors in battery-powered garden and power tools rated up to 1 kW, operating from a 10-cell lithium-ion battery with a voltage range from 36 to 42 V. The design uses 60V, N-channel NexFETsTM featuring a very low drain-to-source resistance (RDS_ON ) of 1.8 mΩ in a SON5x6 SMD package, which results in a very small PCB form factor of 57 × 59 mm. The three-phase gate-driver is used to drive a three-phase MOSFET bridge, which can operate from 6 to 60 V and supports programmable gate current with maximum setting of 2.3-A sink / 1.7-A source. The C2000™ Piccolo™ LaunchPad™ LAUNCHXL-F28027 is used along with this power stage and 120 degree trapezoidal control of BLDC motor with Hall sensors is implemented in software. The cycle by cycle current limit feature in the gate-driver protects the board from excessive current that is caused during motor stalls, by limiting the maximum current allowed in the power stage to a safe level.
• Automotive Reverse Battery Protection Reference Design with Overcurrent and Overvoltage Shutoff
  PMP9498: The PMP9498 reference design is a complete front-end protection solution for automotive systems needing reverse voltage, over-voltage, and over-current protection. Load switch capability is also implemented to digitally control the connection and disconnection of the load to the input supply. The design meets the low Iq requirements for automotive applications during shutoff and features a strong gate current source (typ 30 mA) to drive high power MOSFETs for high current applications.
• Power Reduction Using Dynamic Switching Reference Design
  TIDA-00675: This design shows the power reduction benefits of dynamically switching a load on/off using a load switch. The design guide shows how frequency of switching, duty cycle, and the use of a discharge resistor can have an impact on power consumption.
• 9 to 42Vin 5V/9V/12V @ 3A Synchronous 4-Switch Buck-Boost Converter Reference Design - PMP10624.3 - TI Tool Folder
  PMP10624: PMP10624 is a synchronous 4-switch buck-boost converter which utilizes the LM5175 controller for USB type C applications. The output voltage can be selected for 5V, 9V or 12V at 3A using jumpers or open drain control switches. The LM5175 average current loop sets a maximum output current of 4A.
• Universal 85VAC-264VAC Input, 24V 1A Output, PSR Flyback Reference Design - PMP10468 - TI Tool Folder
  PMP10468?SYS-null-null-findchips-refdes-rd-null-wwe: This design uses low-cost primary side regulation (PSR) IC UCC28700 for universal 85VAC-264VAC input range. A 24V output is generated with maximum 24W rating.
• Xilinx Kintex UltraScale FPGA Power Solution Reference Design with PMBus
  PMP9444: The PMP9444 reference design provides all the power supply rails necessary to power Xilinx's Kintex UltraScale family of FPGAs. It features two UCD90120A's for flexible power up and power down sequencing as well as voltage monitoring, current monitoring, and voltage margining through the PMBus interface. This design uses a 12V input.
• Isolated Flyback Converter for Industrial Bias Supply - Reference Design
  PMP7932.1: PMP7932 is an isolated flyback converter which accepts an input voltage of 12Vin to 24Vin and provides dual polarity ouputs of +12Vout @ 0.25A and -12V @ 0.25A.
• Ten Output QR Flyback and Buck Converter Reference Design - PMP10822.2 - TI Tool Folder
  PMP10822: The PMP10822 reference design utilizes two QR flyback, and four buck converters. The efficiency for the 12V and 24V flyback approaches 87%, while the 16V buck converter has efficiency greater than 89%.
• Non-Isolated Synchronous Buck (1.5V@30A)
  PMP7828.2: This is a synchronous buck converter design with an input voltage range of 10.8V-to-13.2Vin and four regulated outputs: 1Vout@24A, 1.5Vout@30A, 3.3Vout@6.4A, and 1.8Vout@8A.
• 40W Buck Converter Powered out of 48V Reference Design
  PMP10135: PMP10035 is a sycnchronous buck converter with 48V input voltage and 31V output voltage. Due to ceramic capacitors only this design is suitable for automotive applications (48V bus). With switching frequency of 400kHz, the efficiency is higher than 96% at full load.
• Low Power Flyback with Ultra Wide Input Voltage Range Reference Design - PMP10098 - TI Tool Folder
  PMP10098?SYS-null-null-findchips-refdes-rd-null-wwe: This reference design has an ultra-wide input voltage range from 19-375V DC / 19-265V AC, and provides an isolated output of 12.0V/40mA. A linear regulator provides a second output of 5.0V/15mA.
• Biometric Steering Wheel Reference Design - TIDA-00292 - TI Tool Folder
  TIDA-00292?SYS-null-null-findchips-refdes-rd-null-wwe: This reference design is for a concept demonstration of how a driver's pulse rate, respiration rate, and ECG based heart rate can be obtained from a vehicle steering wheel. AFE4400 and AFE4300 from TI's biometric family of analog front-ends (AFE), enables acquisition of all three parameters via simple hand contacts on the steering wheel. This reference design also includes a full BLE connectivity design for easy interface to BLE enabled smartphones, tablets, etc
• 3 LED Driver - PMP7866 - TI Tool Folder
  PMP7866?SYS-null-null-findchips-refdes-rd-null-wwe: This is an LED driver/converter that can power up to three high output LEDs. It has an input voltage range of 9V-to-16Vin and an output of 10.5Vout @ 1A.
• 3-42Vin, 5V at 3A Buck-Boost Optimized for Automotive Cold Crank Reference Design
  PMP10681: This is a modified LM5118 2 switch buck-boost single inductor evaluation module (EVM) optimized to operate through automitive transients such as cold-crank. It is designed to provide 15W (5V, 3A) of output power with an input voltage range of 3V to 42V.
• CISPR 25 Class 5 Rated Multi-Output Power Supply with Pre-Boost for Automotive Cluster Unit - PMP9477.2 - TI Tool Folder
  PMP9477: The PMP9477 design is a conducted EMI optimized multi-output power supply for automotive cluster units. The power supply has a pre-boost stage for cold crank and start-stop operation and two buck regulators. The pre-boost stage features the LM3481 boost controller and will start to operate and regulate a 9.5V output when the input voltage drops below 9.5V. It makes the design a wide input voltage range of 4.5V to 38V suitable for 12V automotive battery systems. The design has two buck regulators following the pre-boost to generate 3 output voltages: the first stage buck generates a 5V, 2A output using the LM26003, and the second stage generates two outputs of 2.8V, 2A and 1.8V, 2A using the LM26420 (the max output power is 15W). The LM26003 is a wide Vin non-synchronous buck regulator, and the LM26420 is a 5V input dual 2A, high frequency synchronous buck regulator. All three ICs are available in automotive grade versions, qualified in AEC-Q100 Grade 1. The board layout is optimized for improved conducted EMI performance. The power inductor in the pre-boost stage is utilized as an input EMI filter, and thus no additional filter components are required. The board is tested under the automotive EMC standard, CISPR 25, and its conducted emissions are in compliance with the CISPR 25 Class 5 requirements. As seen at APEC
• 9 to 42Vin 5V/9V/12V @ 3A Synchronous 4-Switch Buck-Boost Converter Reference Design
  PMP10624.3: PMP10624 is a synchronous 4-switch buck-boost converter which utilizes the LM5175 controller for USB type C applications. The output voltage can be selected for 5V, 9V or 12V at 3A using jumpers or open drain control switches. The LM5175 average current loop sets a maximum output current of 4A.
• High Efficiency 350W AC/DC Power Supply Reference Design
  PMP11303.2: PMP11303 is high-efficiency AC/DC power supply reference design with universal AC input and 25V/13.5A and 12V/1A outputs. LLC+PFC combo IC UCC29950 is applied for the main power stages with 25V/13.5A output while UCC28730 is applied for the auxiliary power with 12V/1A output. This design has low no load power comsumption (152mW@230VAC) and over 93% peak efficiency. This design also meet 80PLUS Gold requirement for 115VAC Internal power supplies.
• Xilinx Virtex Ultrascale FPGA Multi-Gigabit Transceiver (MGT) Power Reference Design with PMBus
  PMP9407: The PMP9407 reference design provides all the power supply rails necessary to power the multi-gigabit transcievers (MGT) in Xilinx's Virtex® Ultrascale™ FPGAs. This design uses a 5V input and has a PMBus interface for current and voltage monitoring, margining, timing delays, and fault monitoring. It uses two TPS544B20's which feature internal current sensing and eliminate the need for an external current sense resistor. This design also meets Xilinx's low output voltage ripple requirements of the MGT rails.
• CISPR 25 Class 5 Multi-Output Power Supply Reference Design for Rear Camera, Automotive ADAS Systems
  PMP9492.1: PMP9492 is a conducted EMI optimized (CISPR 25 Class 5) 9 W Multi output Design for Wide Range Vin automotive ADAS application that supports Cold –Cranking Conditions . The design uses an LM53603 regulator IC (used as Buck), LM26420 (used as dual Buck) and TPS60150 regulator IC (used as Charge pump for 5V output). The design accepts an input voltage of 4.5Vin to 20Vin and provides the outputs of 3.3V @ 1.0A, 2.5V @ 1.0A, 1.8V @ 1.0A, and 5V @ 100mA. It features a small size and is an inexpensive and more efficient solution customized for ADAS and other Automotive related applications. The Board dimension of PMP9492 PCB is 2600mil × 4000mil. Four layer PCB was used for the design.
• RF Sampling 4-GSPS ADC Reference Design with 8-GHz DC-Coupled Differential Amplifier - TIDA-00431 - TI Tool Folder
  TIDA-00431?SYS-null-null-findchips-refdes-rd-null-wwe: Wideband radio frequency (RF) receivers allow greatly increased flexibility in radio designs. The wide instantaneous bandwidth allows flexible tuning without changing hardware and the ability to capture multiple channels at widely separated frequencies. This reference design describes a wideband RF receiver utilizing a 4-GSPS analog-to-digital converter (ADC), with an 8-GHz, DC-coupled, fully differential amplifier front end. The amplifier front end provides signal gain and allows capture of signals down to DC, which is not possible with a balun-coupled input.
• Inverting Buck Boost Power Module Reference Design - PMP10638 - TI Tool Folder
  PMP10638?SYS-null-null-findchips-refdes-rd-null-wwe: The PMP10638 reference design is a -5.2V 4A output power supply using SIMPLE SWITCHER® LMZ31710 Power Module. The reference design takes advantage of the small package and high level integration of LMZ31710 to achieve small solution size. It can support -5.2V 4A output power from 3.1V-3.3V input range. The working frequency is set to 1Mhz and very small ripple voltage.
• Altera Stratix Vgx Reference Design - PMP9284 - TI Tool Folder
  PMP9284?SYS-null-null-findchips-refdes-rd-null-wwe: Reference Design for the Stratix Vgx. This design takes into account sequencing needs. Applicable for 25W applications
• 9 to 42Vin 5V/12V/20V @ 5A Synchronous 4-Switch Buck-Boost Converter Reference Design
  PMP10698.3: PMP10698 is a synchronous 4-switch buck-boost converter which utilizes the LM5175 controller for USB type C applications. The output voltage can be selected for 5V, 12V or 20V at 5A using jumpers or open drain control switches. The LM5175 average current loop sets a maximum output current of 6.25A.
• Four-Switch Buck-Boost Converter with Adjustable Output Voltage for Military Radio Applications - PMP10612 - TI Tool Folder
  PMP10612?SYS-null-null-findchips-refdes-rd-null-wwe: The PMP10612 reference design is 4-switch buck-boost converter optimized for military radio applications. The design offers up to 40W output power from 7.5V to 18V input. The design offers an adjustable output voltage range from 5V to 40V, and very low output voltage ripple.
• Class 3, COT Buck Converter for PoE Application Reference Design
  PMP9416: The PMP9416 reference design is a single output non-isolated buck power supply for PoE applications. It accepts a 48V nominal input and provides a 5V 1A output. The input can be varied from 33V to 57V. The design features the LM5160 synchronous buck converter with the benefit of diode emulated mode which can improve the light load efficiency as compared to FPWM (forced pulse width modulation) mode. The LM5160’s integrated MOSFETs and constant on time control minimize the external component count and enables a small power dense layout.
• TPS92310 - 220VAC, 22W Non-isolated LED Driver with PFC for T8 Tube Application - PMP8002 - TI Tool Folder
  PMP8002?SYS-null-null-findchips-refdes-rd-null-wwe: The main purpose of this reference design is to demonstrate a high performance and low component count offline LED driver with PFC based on TPS92310. This LED driver is designed for converting an AC input to a regulated LED current. The operating conditions and performance of the reference design are as follows:●198VAC to 264VAC, 50Hz Input Voltage ●65V to 75V LED Voltage ●280mA Regulated LED Current ●88% Typical System Efficiency ●High Power Factor>0.9 ●Output Short-Circuit and Open-Circuit Protection.
• UART to Wi-Fi Bridge with 24 VAC Power Reference Design
  TIDA-00375: The TIDA-00375 TI Design uses Texas Instruments SimpleLink Wi-Fi CC3200 Internet-on-a-chip Wireless MCU module to create a data bridge between existing hardware with a logic-level UART interface and a Wi-Fi network. The design also contains a Simple Switcher power supply with a wide input range suitable for 24 volt HVAC systems. The UART interface has buffers to allow this design to interface with equipment that has logic levels between 3.3 volts and 5 volts.
• Automotive Boost Converter with Reverse Battery Protection - PMP7936 - TI Tool Folder
  PMP7936?SYS-null-null-findchips-refdes-rd-null-wwe: PMP7936 is a boost converter capable of 138W output power and targeted for automotive appli-cations. This design uses the LM5122 synchronous boost current-mode PWM controller. The circuit will start at a minimum input of 6.5V and has an operating input voltage range of 4.5V to 42V. The output is 13.8V at 8A continuous, 10A peak. The LM5122 incorporates bypass mode operation, so that when VIN > 13.8V, VOUT is approximately equal to VIN. Reverse battery protection is provided by the LM5050-1 high side OR-ing FET controller.
• System Level reference design for 30W ADAS system with required Automotive Protections
  PMP10652.1: PMP10652 is a System optimized (CISPR 25 Class 3) 30W design for Surround View ADAS system. The design has various protections such as Load dump through TVS (ISO pulse testing), Reverse Voltage (Innovative Smart diode with very low Iq), Battery Disconnect Switch with OVP protection (PFET) and is EMI optimized to meet Conductive EMI limits of CISPR25 Class3 (overall) and Class5 upto 30MHz Range. Input voltage range is between 4.5V to 30V with OVP at 20V and hence will operate in most Cold Cranking conditions. LM74610 is used for Battery reverse protection which utilizes a charge pump to drive an N-channel FET to provide a resistive path for the bypass current to flow. LM53603Q1 is used as front end DC/DC Buck converter which is 2.2MHz switching, Synchronous rectified Wide Vin Buck Converter which can take transient upto 42V. TPS57114Q1 is used to provide power to the cores and it is a high current 2,2MHz switching buck converter. LM26420 is a dual 2.2MHz switching buck converter which is used for generating other required supplies. LM3880 sequencer is used for all the power up and power down sequencing requirements.
• 48Vin, 300W 1/8brick Digital Module with GaN FET Reference Design
  PMP4435.4: The PMP4435 is a DC-DC isolated digital module with GaN mosfet reference design targeted for industrial and telecom applications. The DC input range is 36V-60V, with 12V typical and the output is 12V/5A. An digital controller UCD3138A is used in the design. The efficiency is up to 95.8% with good thermal performance.
• 24V 65W Nominal 130W Surge Offline Flyback Power Supply for Industrial Rails Reference Design
  PMP9643: 24V Output, Constant Voltage / Constant Current, 65W Flyback power supply with 130W surge capability. Primary side regulation eliminates feedback opto-coupler and provides 1% regulation down to no-load. Average efficiency of > 89% and no load power of < 70mW are achieved. Voltage input range is 85VAC-265VAC Input.
• Automotive Power Supply with Pre-Boost Reference Design
  PMP10223.5: The PMP10223 automotive power reference design provides 5.0V @ 1.1A, 3.3V @ 0.6A and 1.3V at 1.0A. A pre-boost provides 9.0V @ 1.7A to ensure proper operation even during startup of the engine. A synchronous buck converters generates 6.0V @ 2.2A as an intermediate rail for the following buck converters.
• Universal AC Input, 5V/10A/50W PSR Flyback Power Supply W/over 88% Avg Efficiency Reference Design - PMP11281 - TI Tool Folder
  PMP11281?SYS-null-null-findchips-refdes-rd-null-wwe: PMP11281 is a quasi-resonant Flyback power suppy based on the UCC28730 primary side regulation (PSR) controller. The elimination of optocoupler using PSR topology promises higher reliability and lower system cost. The design achieves less than 40mW standby power losses and over 88% average efficiency. The design also features UCC2463x synchronous rectification controller.
• Biometric Steering Wheel Reference Design
  TIDA-00292: This reference design is for a concept demonstration of how a driver's pulse rate, respiration rate, and ECG based heart rate can be obtained from a vehicle steering wheel. AFE4400 and AFE4300 from TI's biometric family of analog front-ends (AFE), enables acquisition of all three parameters via simple hand contacts on the steering wheel. This reference design also includes a full BLE connectivity design for easy interface to BLE enabled smartphones, tablets, etc
• Universal Line Power Supply for PLC using PSR Flyback and Compact DC/DC Stages Reference Design
  PMP9185.3: The PMP9185 reference design uses the UCC28710 primary-side regulated flyback controller to generate a 15V output from a univeral AC input with maximum 20W output power followied by DC/DC and LDO stages using TPS54229 and TPS650250, and 5V, 3.3V, 1.8V and 1.2V are provided. A switch on the PCB provides the freedom of supplying DC/DC and LDO from AC input or DC input.
• CISPR 25 Class 5 Rated Multi-Output Power Supply with Pre-Boost for Automotive Cluster Unit
  PMP9477.1: The PMP9477 design is a conducted EMI optimized multi-output power supply for automotive cluster units. The power supply has a pre-boost stage for cold crank and start-stop operation and two buck regulators. The pre-boost stage features the LM3481 boost controller and will start to operate and regulate a 9.5V output when the input voltage drops below 9.5V. It makes the design a wide input voltage range of 4.5V to 38V suitable for 12V automotive battery systems. The design has two buck regulators following the pre-boost to generate 3 output voltages: the first stage buck generates a 5V, 2A output using the LM26003, and the second stage generates two outputs of 2.8V, 2A and 1.8V, 2A using the LM26420 (the max output power is 15W). The LM26003 is a wide Vin non-synchronous buck regulator, and the LM26420 is a 5V input dual 2A, high frequency synchronous buck regulator. All three ICs are available in automotive grade versions, qualified in AEC-Q100 Grade 1. The board layout is optimized for improved conducted EMI performance. The power inductor in the pre-boost stage is utilized as an input EMI filter, and thus no additional filter components are required. The board is tested under the automotive EMC standard, CISPR 25, and its conducted emissions are in compliance with the CISPR 25 Class 5 requirements.
• 300W High-Efficiency Single-Phase Synchronous Buck Converter Reference Design - PMP10514 - TI Tool Folder
  PMP10514?SYS-null-null-findchips-refdes-rd-null-wwe: PMP10514 is a High-Efficiency Single-Phase Synchronous Buck Converter using the LM25117 controller IC. The design accepts an input voltage of 30.4Vin to 33.6Vin (32Vin Nominal) and provides an output of 20 Vout capable of supplying 15A of continuous current to the load.
• Dual, BDC Motor System with independently controlled motors
  TIDA-00116: This Mutli-motor BDC motor system implements an MSP430, a DRV8816, and an Anaheim Automation motor. It's suitable for applications requiring 1A to 2A of motor current to 20KRPM. Motor voltage support is 8V to 32V, and max current is 2.5A. The PWM scheme allows speed control and current regulation. The H-bridge FET supports during current decay, the time interval of current decay, and current deglitch time. The motor drive stage has integrated protection from short-circuit, shoot-through, under-voltage, and over-temperature.
• 200VAC-400VAC Input, 24V 50W Output, PSR Flyback with SiC-FET Reference Design - PMP10416 - TI Tool Folder
  PMP10416?SYS-null-null-findchips-refdes-rd-null-wwe: This design uses low-cost primary side regulation (PSR) IC UCC28700 with a SiC-FET for 200VAC-400VAC input range. A 24V output is generated with maximum 50W rating.
• 40W Synchronous ZETA Converter with Coupled-Inductor Reference Design - PMP9581_REVB - TI Tool Folder
  PMP9581_REVB?SYS-null-null-findchips-refdes-rd-null-wwe: This coupled-inductor, 13.2V at 4A, synchronous ZETA converter achieves greater than 95% efficiency at full load. It is capable of 5A out for Vin greater than 10V. It utilizes all surface mount components, maintains a low temperature rise and is capable of high peak load transients. See PMP9581 REVC for this design with seperate inductors.
• Dual Phase Synchronous Buck (30Vout@10A) - PMP7885 - TI Tool Folder
  PMP7885?SYS-null-null-findchips-refdes-rd-null-wwe: This is a dual-phase, synchronous buck converter with an input voltage range of 30.6V-to-37.4Vin and providing an output of 30Vout @ 10A.
• System Level reference design for 30W ADAS system with required Automotive Protections
  PMP10652.4: PMP10652 is a System optimized (CISPR 25 Class 3) 30W design for Surround View ADAS system. The design has various protections such as Load dump through TVS (ISO pulse testing), Reverse Voltage (Innovative Smart diode with very low Iq), Battery Disconnect Switch with OVP protection (PFET) and is EMI optimized to meet Conductive EMI limits of CISPR25 Class3 (overall) and Class5 upto 30MHz Range. Input voltage range is between 4.5V to 30V with OVP at 20V and hence will operate in most Cold Cranking conditions. LM74610 is used for Battery reverse protection which utilizes a charge pump to drive an N-channel FET to provide a resistive path for the bypass current to flow. LM53603Q1 is used as front end DC/DC Buck converter which is 2.2MHz switching, Synchronous rectified Wide Vin Buck Converter which can take transient upto 42V. TPS57114Q1 is used to provide power to the cores and it is a high current 2,2MHz switching buck converter. LM26420 is a dual 2.2MHz switching buck converter which is used for generating other required supplies. LM3880 sequencer is used for all the power up and power down sequencing requirements.
• Automotive eCall Power Supply Reference Design with Low Intermediate Voltage - PMP9769.2 - TI Tool Folder
  PMP9769: This reference design includes a complete power management solution for a standalone emergency call (eCall) system in an automotive environment. The circuit is supplied directly from the car battery rail. It also manages a backup battery to power the eCall system while the car battery rail is not available. It includes power path management which routes the available power rail directly to four DC/DC converters which are supplying the required functional blocks of the eCall system. The solution is optimized to operate at maximum efficiency while powered from the backup battery.
• TPS92310 - 220VAC, 13W Isolated Flyback LED driver with PFC
  PMP8004: The main purpose of this reference design is to demonstrate a high performance offline flyback LED driver with PFC based on TPS92310. This LED driver is designed for converting an AC input to a regulated LED current. The operating conditions and performance of the reference design are as follows: ● 198VAC to 264VAC, 50Hz Input Voltage ● 28V to 34V LED Voltage ● 400mA Regulated LED Current ● 87% Typical System Efficiency ● High Power Factor > 0.9 ● Output Short-Circuit and Open-Circuit Protection
• 48Vin, 300W 1/8brick Digital Module with GaN FET Reference Design
  PMP4435.3: The PMP4435 is a DC-DC isolated digital module with GaN mosfet reference design targeted for industrial and telecom applications. The DC input range is 36V-60V, with 12V typical and the output is 12V/5A. An digital controller UCD3138A is used in the design. The efficiency is up to 95.8% with good thermal performance.
• Two-switch buck-boost converter with 28.0V @ 2.5A and an input voltage range of 10..32V
  PMP8570: This design is a two-switch buck boost converter which generates an output voltage of 28.0V @ 2.5A from an input voltage range of 10..32V.
• 85V - 265V AC in, 12V/3.3A AC/DC Open Frame Power Supply Based on PSR Flyback Reference Design
  PMP9576: This reference design provides an isolated 12V/3.3A output from a universal 85V-265V AC input. This design achieves efficiencies greater than 84%. Employing the UCC28710D Primary Side Regulation (PSR) Flyback controller eliminates the opto-coupler and secondary side regulation components. The energy saving features of the UCC28710D allow this design to consume less than 75mW when plugged into the wall with no device attached to the output.
• Flyback with Universal Input (85 - 264Vac), Dual Output 12V/2A and 3.3V/0.5A
  PMP9638: The PMP9638 reference design uses the UCC28740 Flyback with resonant-ring valley-switching controller to generate dual DC output 12V/2A and 3.3V/0.5A from a universal AC input. This design minimize switching loss in FET to provide high efficiency. The current regulation feature of the UCC28740 provides accurate current limit protection.
• High Power Density 12Vin, 100W Synchronous DC/DC Step-Down Buck Converter with Inductor-On-Top - TIDA-00510 - TI Tool Folder
  TIDA-00510?SYS-null-null-findchips-refdes-rd-null-wwe: The TPS53355 Inductor-On-Top step-down buck converter design enables high power density through reduction of X-Y PCB area by placing the output inductor on top of the IC and results in 92% minimum efficiency for 66W and 100W output power designs (3.3V and 5V output) requiring only 4x100µF ceramic output caps.
• Four-Output, Flybuck and Buck Converter for High Performance Computing Reference Design
  PMP10837.3: The PMP10837 reference design offers dual output rails for use in enterprise computing. This design implements an isolated step down design, with non-isolated converters on both the primary and secondary side.
• High Eff 2Stage Univ Input Power Supply-Transition Mode PFC LLC Resonant Conv Reference Design
  PMP8911: Low EMI, high efficiency, high power factor and reliable power supply are main focus of the PMP8911 design for telecom applications. Transient mode (TM) power factor correction (PFC) with UCC28051 and LLC series resonant converter (SRC) with UCC25600 are applied in PMP8911. Low EMI is expected with zero voltage switching on TM-PFC and LLC-SRC switches. An overall 92% efficiency is achieved at 100W full load. In addition, several protections are embedded into this design which includes input under-voltage protection, input over-voltage protection, output over-voltage protection, and output hic-cup over-power protection.
• Body Weight Scale Reference Design with Body Composition capability and BLE Connectivity - TIDA-00009 - TI Tool Folder
  TIDA-00009?SYS-null-null-findchips-refdes-rd-null-wwe: This reference design is for a complete body weight scale end equipment with body composition capability featuring TI signal chain, power, and connectivity components. With TI's AFE4300 weigh scale/body composition AFE, you can accelerate your body weight scale design or quickly add body composition measurement features to your existing platform. This reference design also includes the full BLE connectivity design for easy interface to BLE enabled smartphones, tablets, etc.
• Ten Output QR Flyback and Buck Converter Reference Design - PMP10822.9 - TI Tool Folder
  PMP10822: The PMP10822 reference design utilizes two QR flyback, and four buck converters. The efficiency for the 12V and 24V flyback approaches 87%, while the 16V buck converter has efficiency greater than 89%.
• Isolated offline LED driver with 120V AC and driving 4X4 LED string at 1.5A
  PMP7753: 120Vac Isolated Offline Flyback AC to DC converter with constant current Feedback for driving 4 LEDs at 1.5A. Also implemented is a simple circuit to decode a dimming signal from a TRIAC, This dimming decoder circuit, controls the dimming level of the LEDs.
• Single-Supply Strain Gauge in a Bridge Configuration Reference Design
  TIPD170: This strain gauge reference design accurately measures the resistance of a strain gauge by being placed in a bridge configuration. The differential voltage of the bridge produced by variation in strain gauge resistance is amplified using the INA333. The bridge excitation voltage and INA333 reference voltage is supplied using the REF5025.
• UPOE High-Efficiency Flyback Converter (19V/2.3A) for Forced 4-Pair PoE PD Apps Reference Design - TIDA-00539 - TI Tool Folder
  TIDA-00539?SYS-null-null-findchips-refdes-rd-null-wwe: TIDA-00539 uses two TPS2378 PD controllers for a forced 4-pair UPOE solution to 51W non-standard PoE PD applications. It incorportates the UCC2897A controller in a high-efficiency, great transient response (driven) synch flyback converter capble of 19V at 2.3A.
• PoE PSE Type 2 (30W) IEEE 802.3at Fully Autonomous Quad Port Solution.
  TIDA-00290: A fully autonomous IEEE802.3at, Type 2 (30W) Power-over-Ethernet (PoE) 4 Port Power Sourcing Equipment (PSE) solution. An additional configuration of two non-standard, high power ports (<60W) is provided. Both configurations support Gigabit Ethernet data pass through in 1000BASE-T ports. This reference design is made up of two boards: Motherboard (TPS23861EVM-612) and Daughter board (TPS23861EVM-613). The daughter board features two TPS23861 IEEE 802.3at PoE PSE controller devices. The motherboard provides a multi-port base platform interface for the daughter board. Additionally, the motherboard provides interfaces for two optional boards: MSP-EXP430G2 LaunchPad™ (if custom Power Management programmability is desired) and USB-TO-GPIO Interface Adapter (if PC GUI based Power Management configuration is desired). The complete solution has undergone exhaustive PoE testing and passes all industry-recognized conformance/interoperability test suites allowing customers to copy/paste the design without concern. The 2-layer PCB, daughter card, design delivers all of this on a low cost platform.
• Two-Wire Interface to a HIPERFACE DSL Encoder Reference Design - TIDA-00177 - TI Tool Folder
  TIDA-00177?SYS-null-null-findchips-refdes-rd-null-wwe: The TIDA-00177 reference design is an EMC compliant industrial interface to a two-wire HIPERFACE DSL encoder. Applications include industrial servo drives. The design features a 3.3-V supply RS485 transceiver and line termination and coupling for encoder power over RS485 as per HIPERFACE DSL specification. The design has been tested up to 100m cable length with an integrated cable, where the encoder’s two-wire twisted pair was integrated in the same motor cable. The encoder connector output is protected against over-voltage and short circuit to prevent damage to an encoder or during a cable short. The design features an industrial compliant 24-V input with wide range from 18-36V. A 3.3V I/O connector with logic signals for easy interface to a host processor with HIPERFACE DSL Master IP Core is made available.
• 9 to 60Vin 12Vout @ 5A Single-Phase Isolated Synchronous Flyback Converter Reference Design - PMP9256 - TI Tool Folder
  PMP9256?SYS-null-null-findchips-refdes-rd-null-wwe: PMP9256 is an isolated synchronous flyback converter utilizing the LM5122 for industrial applications. The benefit of using a synchronous flyback is higher efficiency compared to a non-synchronous flyback.
• 335W Single Stage LLC-SRC Converter Reference Design
  PMP10375.1: The PMP10375 reference design is a single stage LLC series resonant converter (SRC), producing up to a 335W output using UCC25600 resonant controller. With the use of single stage LLC-SRC, the converter efficiency goes up to 90% at 335W full output power with 120VAC input.
• CISPR 25 Class 5 Rated 10 W Reference Design for Automotive USB Charger System
  PMP9496.1: The PMP9496 reference design is a conducted EMI-optimized (CISPR 25 Class 5) 10 W design for efficient automotive USB charger application utilizing the LM53603 regulator IC (2.1MHz fully-integrated synchronous buck for automotive application ) and TPS2549 USB switch(TPS2549-Q1 Automotive USB Charging Port Controller with Integrated Power Switch & Cable Compensation). The design accepts wide input voltage range of 7Vin to 25Vin and provides the outputs of 5V@2.1A. It features a small size and is an inexpensive and more efficient solution customized for automotive USB charger application. The board dimension of the PMP9496 PCB is 2800mil * 4000mil. Four layer PCB was used for the design.
• Single Supply Analog Input Module Reference Design with 16-Bit, 8-Channel ADC for PLC - TIPD166 - TI Tool Folder
  TIPD166?SYS-null-null-findchips-refdes-rd-null-wwe: This design is for a 16-bit, 8-channel analog input module for industrial programmable logic controller (PLC) systems. The circuit is realized with an 8-channel, 16-bit, successive-approximation-register (SAR), analog-to-digital converter (ADC) with an integrated precision reference and analog front-end (AFE) circuit.
• 9 to 42Vin 5V/9V/12V @ 3A Synchronous 4-Switch Buck-Boost Converter Reference Design
  PMP10624.1: PMP10624 is a synchronous 4-switch buck-boost converter which utilizes the LM5175 controller for USB type C applications. The output voltage can be selected for 5V, 9V or 12V at 3A using jumpers or open drain control switches. The LM5175 average current loop sets a maximum output current of 4A.
• Xilinx Zynq 7000 Series (XC7Z045) 20W Reference Design
  PMP10613.2: The PMP10613 reference design provides all the power supply rails necessary to power Xilinx® Zynq® 7000 series (XC7Z045) FPGA. This design uses several LMZ3 series modules, LDOs, and a DDR termination regulator to provide all the necessary rails to power the FPGA. It also features one LM3880 for power up and power down sequencing. This design uses a 12V input.
• 10.8Vin to 13.2Vin; 48Vout @ 7.3A; 4-Phase Synchronous Boost Converter
  PMP7944: A 4-phase synchronous boost converter that accepts an input voltage of 10.8Vin to 13.2Vin providing an output of 48Vout capable of delivering 7.3A.
• UPOE High-Efficiency Flyback Converter (12V/3.8A) Reference Design for PoE PD Applications - TIDA-00741 - TI Tool Folder
  TIDA-00741?SYS-null-null-findchips-refdes-rd-null-wwe: TIDA-00741 uses two TPS2378 PD controllers for a forced 4-pair UPOE solution to 51W non-standard PoE PD applications. It incorportates the UCC2897A controller in a high-efficiency, great transient response (driven) synch flyback converter capble of 12V at 3.8A.
• CISPR 25 Class 5 Multi-Output Power Supply Reference Design for Rear Camera, Automotive ADAS Systems
  PMP9492.2: PMP9492 is a conducted EMI optimized (CISPR 25 Class 5) 9 W Multi output Design for Wide Range Vin automotive ADAS application that supports Cold –Cranking Conditions . The design uses an LM53603 regulator IC (used as Buck), LM26420 (used as dual Buck) and TPS60150 regulator IC (used as Charge pump for 5V output). The design accepts an input voltage of 4.5Vin to 20Vin and provides the outputs of 3.3V @ 1.0A, 2.5V @ 1.0A, 1.8V @ 1.0A, and 5V @ 100mA. It features a small size and is an inexpensive and more efficient solution customized for ADAS and other Automotive related applications. The Board dimension of PMP9492 PCB is 2600mil × 4000mil. Four layer PCB was used for the design.
• 3 LED Driver
  PMP7866: This is an LED driver/converter that can power up to three high output LEDs. It has an input voltage range of 9V-to-16Vin and an output of 10.5Vout @ 1A.
• Four-Switch Buck-Boost Converter with Adjustable Output Voltage for Military Radio Applications
  PMP10612: The PMP10612 reference design is 4-switch buck-boost converter optimized for military radio applications. The design offers up to 40W output power from 7.5V to 18V input. The design offers an adjustable output voltage range from 5V to 40V, and very low output voltage ripple.
• Single LED with High Current 20A Application using TPS92641 - PMP8016 - TI Tool Folder
  PMP8016?SYS-null-null-findchips-refdes-rd-null-wwe: The main purpose of this reference design is to demonstrate a high performance, high current and easy to use, synchronous buck LED driver based on TPS92641. This LED driver is designed for application with using high power single LED within 20A.The operating conditions and performance of the reference design are as follows:
• 38V@2A Synchronous Boost Reference Design
  PMP10324: The PMP10324 sync-boost reference design provides 38V @ 2A over a wide input range covering the 24V rail. It uses dual external FETs to achieve a full load efficiency of 97% at 24Vin. This design uses minimal footprint parts with all ceramic capacitors.
• Non-Synchronous Flyback Converter with Dual-Output (5V@.25A) - PMP7901.1 - TI Tool Folder
  PMP7901: PMP7901 is a Non-Synchronous Flyback converter with an input of 8 volts to 18 volts. It has an Isolated dual-output of 5 volts and negitive 5 volts at 0.25 Amps.
• Four-Output, Flybuck and Buck Converter for High Performance Computing Reference Design
  PMP10837.1: The PMP10837 reference design offers dual output rails for use in enterprise computing. This design implements an isolated step down design, with non-isolated converters on both the primary and secondary side.
• Current Controlled Driver for 230V AC Solenoids Reference Design
  TIDA-00284: TIDA-00284 proposes to integrate current control and plunger movement detection into an AC solenoid coil. This reference design provides a solution to control the solenoid current using a PWM-based controller along with a Hall sensor to detect plunger movement and switch from peak current to hold current mode Various applications in the field of industrial automation and material processing will benefit from up-to 70% reduced power consumption, accelerated process time, greatly simplified usage and enhanced monitoring capabilities.
• Automotive Cluster Telltale Driver Reference Design
  TIDA-00278: This TI reference design is an automotive cluster telltale solution that includes a monolithic, medium-voltage, low-current power 12-bit shift register designed for use in systems that require relatively moderate load power, such as LEDs found in automotive clusters. This design is one part of an entire automotive cluster system solution optimized for the mid-end cluster market. The entire solution supports 4.5-40V system capabilities that can withstand cold crank, start stop, and load dump conditions.
• Noise-immune Capacitive Proximity Sensor System Reference Design
  TIDA-00466: The FDC2214 proximity and capacitive sensing design demonstrates the use of TI's capacitive sensing technology to sense and detect the presence of various objects. The design is a complete hardware and firmware solution. The firmware processes the data from one proximity sensor and two capacitive touch buttons via the FDC2214 to determine whether an object is in the intended sensing area. Dedicated colored LEDs light up once the device detects a target in close proximity to the board or detects a press on the buttons. The design is powered by one AA-battery.
• Dual-Channel Full-Bridge Converter (54V @ 30A) for PoE Power Sourcing (PSE) - PMP6712 - TI Tool Folder
  PMP6712?SYS-null-null-findchips-refdes-rd-null-wwe: PMP6712 is a phase-shifted full-bridge converter capable of delivering 1600W of isolated output power and achieving efficiency of greater than 96%. This design uses the UCC28950 controller in a dual phase master-slave configuration. An LM5017 constant on-time synchronous buck regulator provides bias power to primary and secondary-side circuits using a coupled inductor with isolated flyback winding. The isolation voltage is specified as 2250VDC, allowing this design to be used as a system supply for Power Over Ethernet and other telecommunications applications.
• 36Vin to 60Vin; 15Vout @ 0.05A (Non-Isolated) and 15Vout @ 0.35A (Isolated); Flybuck Converter
  PMP7953.1: A flybuck converter using the LM5017 synchronous buck regulator, which accepts an input voltage of 36Vin to 60Vin and provides two outputs: one non-isolated output of 15Vout capable of supplying 0.05A and an isolated output of 15Vout capable of supplying 0.35A.
• System Level reference design for 30W ADAS system with required Automotive Protections
  PMP10652.3: PMP10652 is a System optimized (CISPR 25 Class 3) 30W design for Surround View ADAS system. The design has various protections such as Load dump through TVS (ISO pulse testing), Reverse Voltage (Innovative Smart diode with very low Iq), Battery Disconnect Switch with OVP protection (PFET) and is EMI optimized to meet Conductive EMI limits of CISPR25 Class3 (overall) and Class5 upto 30MHz Range. Input voltage range is between 4.5V to 30V with OVP at 20V and hence will operate in most Cold Cranking conditions. LM74610 is used for Battery reverse protection which utilizes a charge pump to drive an N-channel FET to provide a resistive path for the bypass current to flow. LM53603Q1 is used as front end DC/DC Buck converter which is 2.2MHz switching, Synchronous rectified Wide Vin Buck Converter which can take transient upto 42V. TPS57114Q1 is used to provide power to the cores and it is a high current 2,2MHz switching buck converter. LM26420 is a dual 2.2MHz switching buck converter which is used for generating other required supplies. LM3880 sequencer is used for all the power up and power down sequencing requirements.
• Single LED with High Current 20A Application using TPS92641
  PMP8016: The main purpose of this reference design is to demonstrate a high performance, high current and easy to use, synchronous buck LED driver based on TPS92641. This LED driver is designed for application with using high power single LED within 20A.The operating conditions and performance of the reference design are as follows:
• Reference Design - High Efficiency Two-Phase Synchronous Buck Delivers 300W
  PMP9700: This two-phase synchronous buck operates from 24VDC and supplies an output of 15V@20A. Operation at 300KHz (per phase) delivers small size and greater than 96% efficiency.
• CISPR 25 Class 5 Rated 6.6W Automotive Power Reference Design
  PMP9398: The PMP9398 reference design is a conducted EMI optimized 6.6W power supply design for automotive application. It features the SIMPLE SWITCHER® LM46002 synchronous buck regulator and provides a 3.3V, max 2A output. The input voltage range is 4.5V to 60V suitable for 12V automotive battery supply. The reference design has the input EMI filter stage, and the conducted EMI is tested under the CISPR 25 automotive EMC standard. The design is compliant with the Class 5 conducted emissions standard.
• Current Controlled Driver for 24-V DC Solenoid with Plunger Fault Detection Reference Design
  TIDA-00289: The TI Design TIDA-00289 proposes to integrate current control and plunger movement detection into the solenoid coil. Various applications in the field of industrial automation and material processing will benefit from up-to 70% reduced power consumption, accelerated process time, greatly simplified usage and enhanced monitoring capabilities.
• 350W PSU with Universal AC Input and 28V Output - Reference Design
  PMP9531: High efficiency, high power factor and reliable power supply are the main focus of the PMP9531 design for motor driver applications. Transition mode (TM) power factor correction (PFC) with UCC28051 and LLC series resonant converter (SRC) with UCC25600 are applied in PMP9531. In addition, a high-side buck converter with UCC28710 is applied here as the bias supply. 93% converter efficiency is achieved at high line while still obtaining 90% converter efficiency at low line.
• 65W High-efficiency CoC-5 tier2/DOE Level VI AC Adapter
  TIDA-00519: This is a high efficiency 65W AC/DC design for a Universal input (85Vac to 265Vac) to 19.5V @3.33A output exceeding CoC-5 Tier2 and DOE Level VI requirements for external power supplies using the LM5023 Quasi-Resontant Flyback Controller with UCC24630 Synchronous Rectification Controller and CSD19531Q5A MOSFET. Additionally the LM8364 reset controller is used to provide input line AC UVLO protection. As seen at APEC
• High-Efficiency Adjustable Output Synchronous Boost Converter Reference Design
  PMP10538: PMP10538 is a Single-Phase Synchronous Boost Converter using the LM5122 controller IC. The design accepts an input voltage of 18Vin to 20Vin and provides an output of 30Vout to 54Vout, capable of supplying 1.7A of continuous current to the load or 0A to 3.4A Max. The output voltage can be adjusted between 30Vout and 54Vout by driving the Vadj. input of the Op-Amp circuit between 0V and 3V.
• 33W Offline QR Flyback Converter with Multiple Outputs Reference Design
  PMP10020: This design uses the UCC28610 quasi-resonant flyback controller to generate 3 isolated outputs from an universal input (90VAC - 290VAC). It was built on a low cost single layer PCB. The regulated output provides 12V@1.89A and the maximum output power is 33W.
• Universal Line Power Supply for PLC using PSR Flyback and Compact DC/DC Stages Reference Design
  PMP9185.2: The PMP9185 reference design uses the UCC28710 primary-side regulated flyback controller to generate a 15V output from a univeral AC input with maximum 20W output power followied by DC/DC and LDO stages using TPS54229 and TPS650250, and 5V, 3.3V, 1.8V and 1.2V are provided. A switch on the PCB provides the freedom of supplying DC/DC and LDO from AC input or DC input.
• Universal AC Input, Dual 12V, -8.5V Output Quasi-Resonant Flyback Converter Reference Design - PMP10150.1 - TI Tool Folder
  PMP10150: The PMP10150 reference design uses the UCC28600 quasi-resonant flyback controller to generate a 12V and a -8.5V output from an universal AC input. An optocoupler is used to regulate the 12V output.
• 24Vdc Input (Double Car Battery) Automotive Multiphase Sync-Buck Reference Design - PMP10260 - TI Tool Folder
  PMP10260?SYS-null-null-findchips-refdes-rd-null-wwe: This high-efficiency, high-power reference design uses the LM5119 two-phase synchronous-buck controller to regulate 14.4V at 60A. This design can be used to supply single car battery power from a double battery system, often found in trucks. Features include input EMI filtering, output hot swap protection, input/output current monitoring and temperature monitoring.
• 360W Phase Shift Full Bridge Resonant LLC with High Side Low Side Driver Reference Design - TIDA-00381 - TI Tool Folder
  TIDA-00381?SYS-null-null-findchips-refdes-rd-null-wwe: The power supply employs Full Bridge Resonant LLC with phase shift operating at ramp up, light load, low output voltage. This operating mode can replace PWM operating mode in LLC, which can improve efficiency signficantly in light load.
• CISPR 22 Class-B Compliant Synchronous Wide Vin Buck Converter Reference Design
  PMP9457: This CISPR 22 Class-B compliant reference design features LM46002 in a 75x86mm board size. The synchronous buck regulator, LM46002, is used to generate 3.3V. The input voltage range is 4.5V to 45V and is suitable for 24V industrial supply.
• 2.2MHz Switching, Synchronous Split Supply Reference Design for 12V Battery with all Protections - PMP10651.2 - TI Tool Folder
  PMP10651: PMP10651 is a low noise, multi-output SMPS design where LM53603 is used in Inverting Buck-Boost Fly buck topology to generate positive and negative supply needed in multiple noise sensitive applications such as powering High Speed Video Amplifier, RF amplifier, Precision Low noise amplifier etc. The design accepts an input voltage of 7Vin to 15 Vin DC (from 12V Lead Acid Battery) and provides outputs of +12V@500mA, -12v@500mA, 5V @400mA and 3.3V@150mA. It features a small size and is an inexpensive and more efficient solution to using Flyback or Pushpull converters .
• Xilinx Virtex® UltraScale™ FPGA Multi-Gigabit Transceiver (MGT) Power Solution
  PMP10520.2: The PMP10520 reference design provides all the power supply rails (1V/20A, 1.2V/30A, 1.8V/4A) necessary to power the multi-gigabit transceivers (MGT) in Xilinx's Virtex® UltraScale™ FPGAs. This design uses a 5V input and has a PMBus interface for current and voltage monitoring, margining, timing delays, and fault monitoring. It uses both TPS544C20 and TPS544B20 which feature internal current sensing and eliminate the need for an external current sense resistor. This design also meets Xilinx's low output voltage ripple requirements of the MGT rails.
• Current Controlled Driver for 24-V DC Solenoid with Plunger Fault Detection Reference Design - TIDA-00289 - TI Tool Folder
  TIDA-00289?SYS-null-null-findchips-refdes-rd-null-wwe: The TI Design TIDA-00289 proposes to integrate current control and plunger movement detection into the solenoid coil. Various applications in the field of industrial automation and material processing will benefit from up-to 70% reduced power consumption, accelerated process time, greatly simplified usage and enhanced monitoring capabilities.
• PSR Flyback Reference Design for 120V+/-15% AC Input and 24V/6A Output - PMP10912 - TI Tool Folder
  PMP10912?SYS-null-null-findchips-refdes-rd-null-wwe: The PMP10912 reference design uses the UCC28630 primary-side regulated controller on a two-switch flyback controller to generate a 24V/6A output from 120VAC input with safety isolation rated transformer. Over 87% efficiency is achieved at full load in this design.
• Body Weight Scale Reference Design with Body Composition capability and BLE Connectivity
  TIDA-00009: This reference design is for a complete body weight scale end equipment with body composition capability featuring TI signal chain, power, and connectivity components. With TI's AFE4300 weigh scale/body composition AFE, you can accelerate your body weight scale design or quickly add body composition measurement features to your existing platform. This reference design also includes the full BLE connectivity design for easy interface to BLE enabled smartphones, tablets, etc.
• High Input Voltage Synchronous Buck Provides Two Independent Outputs of 28V at 2A and 16V at 4A
  PMP9227.1: The LM5119 controller allows the user to have two separate regulated outputs or the capability to combine the outputs (of the same voltage) into a two-phase regulator. This design operates from a 36V - 51V input and regulates 28V@2A (with transients up to 7A) and 16V@4A (with transients up to 6A).
• Altera® Stratix® V FPGA Power Solution - PMP9365 - TI Tool Folder
  PMP9365?SYS-null-null-findchips-refdes-rd-null-wwe: The PMP9365 reference design provides all the power supply rails necessary to power Altera's Stratix V family of FPGAs. This design uses several LMZ3 series modules, LDOs, and a DDR termination regulator to provide all the necessary rails to power the FPGA. It also features two LM3880's for flexible power up and power down sequencing. This design uses a 12V input.
• Hercules Safety MCU Industrial Power Solution Reference Design
  PMP10189.1: This reference design is a complete power solution for the Hercules™ Safety MCU. The input voltage can be in the range of 48..60V and it provides five different output rails with 12.0V @ 30mA, 5.0V @ 240mA, 3.3V @ 620mA, 3.3V @ 230mA and 1.2V @ 700mA.
• Xilinx Virtex UltraScale FPGA Power Solution with PMBus Reference Design - PMP9475 - TI Tool Folder
  PMP9475?SYS-null-null-findchips-refdes-rd-null-wwe: The PMP9475 12V-input reference design provides all the power supply rails necessary to power Xilinx's Virtex® UltraScale™ family of FPGAs in a compact, highly efficient design. This design uses several of TI's PMBus Point-Of-Load voltage regulators for ease of design/configuration and telemetry of critical rails. It features a UCD90120A for flexible power up and power down sequencing as well as voltage monitoring, current monitoring, and voltage margining through the PMBus interface.
• Xilinx Zynq 7000 Series (XC7Z045) 20W Reference Design
  PMP10613.1: The PMP10613 reference design provides all the power supply rails necessary to power Xilinx® Zynq® 7000 series (XC7Z045) FPGA. This design uses several LMZ3 series modules, LDOs, and a DDR termination regulator to provide all the necessary rails to power the FPGA. It also features one LM3880 for power up and power down sequencing. This design uses a 12V input.
• Clocking Solution Reference Design for GSPS ADCs
  TIDA-00359: Low cost, high performance clocking solution for GSPS data converters. This reference design discusses the use of a TRF3765, a low noise frequency synthesizer, generating the sampling clock for a 4 GSPS analog-to-digital converter (ADC12J4000). Experiments demonstrate data sheet comparable SNR and SFDR performance.
• Automotive Range SEPIC Converter Delivers 12V@1A Reference Design - PMP8937 - TI Tool Folder
  PMP8937?SYS-null-null-findchips-refdes-rd-null-wwe: This wide input voltage range SEPIC operates from an input of 6V - 48V and produces greater than 89% efficiency. Its compact size and low cost make it idea for automotive and telecom applications.
• Altera® Stratix® V FPGA Power Solution
  PMP9365: The PMP9365 reference design provides all the power supply rails necessary to power Altera's Stratix V family of FPGAs. This design uses several LMZ3 series modules, LDOs, and a DDR termination regulator to provide all the necessary rails to power the FPGA. It also features two LM3880's for flexible power up and power down sequencing. This design uses a 12V input.
• SMBus 1- to 4-cell Hybrid Power Boost Mode Battery Charge Controller Reference Design
  TIDA-00657: The TIDA-00657 reference design enables high efficiency (90+% @1-2A) and faster charge with high charging current up to 3A. The design uses TI's BQ24780 Industrial Innovative Charge Controlller with Hybrid Power Boost Mode and also features power and processor hot monitoring capability.
• Automotive Dual-buck with Pre-boost 3.3V @ 2.3A and 3.3V @ 1.8A Reference Design - PMP8637.3 - TI Tool Folder
  PMP8637: This design is an automotive power solution with two synchronous bucks and a pre-boost to keep the output voltage stable during cranking. The bucks provide 3.3V @ 2.3A and 3.3V @ 1.8A, the output of the pre-boost is 7.0V @ 2.1A.
• Indoor Light Energy Harvesting Reference Design for Bluetooth Low Energy (BLE) Beacon Subsystem - TIDA-00100 - TI Tool Folder
  TIDA-00100?SYS-null-null-findchips-refdes-rd-null-wwe: The Indoor Light Energy Harvesting Reference Design for Bluetooth Low Energy (BLE) Beacon Subsystem provides a solution where by with just the power of the typical indoor lighting in a retail environment (greater than 250 LUX) the Bluetooth Low Energy chip can broadcast BLE beacons. This subsystem reference design is highly differentiated over existing solutions as it incorporates no batteries, thus eliminating the hassle of battery replacement, battery charging, and saving costs associated with battery maintenance. This solution also ensures that there are no constraints around installation as long as there is typical indoor lighting available. There is also no ON/OFF switch; the entire load connection and disconnection is handled by the power management IC therefore ensuring that the solution is self managing.
• TPS92310 Universal 18W - PMP8006 - TI Tool Folder
  PMP8006?SYS-null-null-findchips-refdes-rd-null-wwe: The main purpose of this reference design is to demonstrate a high efficiency offline LED driver with PFC based on TPS92310. This LED driver is designed for converting an AC input to a regulated LED current.The operating conditions and performance of the reference design are as follows: 1.90VAC to 264VAC, 60/50HZ Input voltage;2.55V to 65V LED Forward Voltage;3.275mA Regulated LED Current;4.System Efficiency ≥ 90%;5.High Power Factor > 0.9;6.Output Short-Circuit and Open-Circuit Protection.
• Automotive Boost Converter with Reverse Battery Protection
  PMP7936: PMP7936 is a boost converter capable of 138W output power and targeted for automotive appli-cations. This design uses the LM5122 synchronous boost current-mode PWM controller. The circuit will start at a minimum input of 6.5V and has an operating input voltage range of 4.5V to 42V. The output is 13.8V at 8A continuous, 10A peak. The LM5122 incorporates bypass mode operation, so that when VIN > 13.8V, VOUT is approximately equal to VIN. Reverse battery protection is provided by the LM5050-1 high side OR-ing FET controller.
• Current Controlled Driver for 230V AC Solenoids Reference Design - TIDA-00284 - TI Tool Folder
  TIDA-00284?SYS-null-null-findchips-refdes-rd-null-wwe: TIDA-00284 proposes to integrate current control and plunger movement detection into an AC solenoid coil. This reference design provides a solution to control the solenoid current using a PWM-based controller along with a Hall sensor to detect plunger movement and switch from peak current to hold current mode Various applications in the field of industrial automation and material processing will benefit from up-to 70% reduced power consumption, accelerated process time, greatly simplified usage and enhanced monitoring capabilities.
• Power Solution for an Engineering Equipment Fuel Injector
  PMP7967: The PMP7967 converts a DC input of 6V-42V to an output of 90V at 1.5A. The design uses four interleaved LM5122 boost controllers with each controller switching at 100kHz. The resulting 4-phase boost converter has a ripple frequency of 400kHz. Freqeucny can also be synchronized to an external signal. Four 330μF aluminum electrolytic capacitors are used at the output to support sudden load current demands in the fuel injector solenoids.
• Universal Digital Interface to Absolute Position Encoders Reference Design - TIDA-00179 - TI Tool Folder
  TIDA-00179?SYS-null-null-findchips-refdes-rd-null-wwe: The TIDA-00179 reference design is an EMC compliant universal digital interface to connect to absolute position encoders, like EnDat 2.2, BiSS®, SSI or HIPERFACE DSL®. The design supports a wide input voltage range from 15-60V (24V nom). A connector with 3.3V logic I/O signals allows for direct interface to the host processor to run the master protocol. The design allows the host processor to select between a 4-wire encoder interface like EnDat 2.2 and BiSS or a 2-wire interface with power over RS485 like HIPERFACE DSL. To meet the selected encoder's supply range, the design offers a programmable output voltage with either 5.25V or 11V. This design’s power supply offers protection against over-voltage and short circuit according to the selected encoder’s voltage range to prevent damage during a cable short. TIDA-00179 has been tested up to 100m cable length with EnDat 2.2 and 2-wire HIPERFACE DSL encoders.
• High-Efficiency 4 Phase Synchronous Boost Conv for Automotive Trunk Amplifier App Reference Design
  PMP7969: PMP7969 is a very high efficiency 4 phase boost controller synchronizable to external clock. Light load efficiency is excellent due to phase shedding capability. Synchronous rectifier also improves efficiency. High effective switching frequency obtained with multiphase over single phase, and current sharing accuracy of ±10%. Bypass mode capable when Vin > Vout.
• Ten Output QR Flyback and Buck Converter Reference Design
  PMP10822.7: The PMP10822 reference design utilizes two QR flyback, and four buck converters. The efficiency for the 12V and 24V flyback approaches 87%, while the 16V buck converter has efficiency greater than 89%.
• Power Reference Design for Xilinx Ultrascale Kintex FPGA Multi-Gigabit Transciever (MGT) with PMBus
  PMP9463: The PMP9463 reference design provides all the power supply rails necessary to power the multi-gigabit transcievers (MGT) in Xilinx's Ultrascale™ Kintex® FPGAs. It utilizes a PMBus interface for current and voltage monitoring and meets Xilinx's low output voltage ripple requirement. This design uses a 5V input and offers a low cost discrete solution.
• High Efficiency, 24Vin, Synchronous Buck Converter with PMBus for Industrial Bus POL Applications
  PMP11220: The PMP11220 reference design is a high efficiency, high power density, PMBus synchronous buck converter design for programming, and margining the power supply including output voltage. With a nominal input of 24V meant for industrial bus applications, this design allows for programmable output voltages and minimal power loss, all in a small board space. DCAP2 control mode requires no loop compensation, enabling ease of design, while offering ultra-fast load transient response and use with all MLCC output caps.
• Non-Synchronous Flyback Converter with Dual-Output - PMP7901 - TI Tool Folder
  PMP7901?SYS-null-null-findchips-refdes-rd-null-wwe: PMP7901 is a Non-Synchronous Flyback converter with an input of 8 volts to 18 volts. It has an Isolated dual-output of 5 volts and negative 5 volts at 0.25 Amps.
• Non-Synchronous Boost with Triple Outputs (12V@.15A)
  PMP7833.1: This is a non-synchronous boost converter with an input voltage range of 4.5V-to-5.5Vin and three regulated outputs: 12Vout @ 0.15A, 10.6Vout @ 0.1A, and 3.3Vout @ 0.03A
• High-Eff 2Stage Univ Input Pwr Supply Using Trans Mode PFC/LLC Resonant Conv Reference Design - PMP8920 - TI Tool Folder
  PMP8920?SYS-null-null-findchips-refdes-rd-null-wwe: Low EMI, high efficiency, high power factor and reliable power supply are main focus of the PMP8920 design for telecom applications. Transient mode (TM) power factor correction (PFC) with UCC28051 and LLC series resonant converter (SRC) with UCC25600 are applied in PMP8911. In addition, synchronous rectifier (SR) IC UCC24610 is applied to LLC output rectifier stage. Low EMI is expected with zero voltage switching on TM-PFC and LLC-SRC switches. An overall 91% efficiency is achieved at 100W full load. In addition, several protections are embedded into this design which includes input under-voltage protection, input over-voltage protection, output over-voltage protection, and output hic-cup over-power protection.
• 18-48VDC Input, 24V/1A Flyback Reference Design
  PMP11047: This reference design provides an isolated 24V/1A output from an 18V-48VDC. The supply is laid out on a small 1.1" by 2.4" circuit board, and achieves over 90% peak efficiency.
• Automotive Buck-boost Converter Providing 8V @ 1.5A Reference Design - PMP8635 - TI Tool Folder
  PMP8635?SYS-null-null-findchips-refdes-rd-null-wwe: This design is a buck-boost converter for automotive applications covering an input voltage range of 2..20V. It provides an output voltage of 8.0V @ 1.5A continuous / 2.5A peak.
• Triple Output Isolated Fly-Buck Power Supply for Industrial Application Reference Design - PMP10516 - TI Tool Folder
  PMP10516?SYS-null-null-findchips-refdes-rd-null-wwe: PMP10516 is an Isolated Flybuck Converter using the LM25017 regulator IC. The design accepts an input voltage of 20.4Vin to 28.8Vin (40Vin Max. Peak) and provides three isolated outputs. The +5Vout rail is regulated for precision using the LP2951 linear regulator.
• 4-Channel LED Spotlight Driver Reference Design
  PMP10171: The PMP10171 reference design is a boost LED driver with four outputs. It has an input voltage range of 10 .. 30V and provides 500mA at 40V maximum. A microcontroller provides an adjustable PWM signal for adjusting the brightness of the LEDs.
• Automotive Buck-boost Converter Providing 5.7V @ 1.2A Reference Design
  PMP8637.1: This design is a buck-boost converter for automotive applications covering an input voltage range of 3.5 .. 35V. It provides an output voltage of 5.7V @ 1.2A.
• 14-Channel Active Cell Balance Battery Management Reference Design
  TIDA-00239: Active Balance chipset for use in large format Lithium-ion batteries that provides monitoring, balancing, and communications. With precise and robust active balancing, the Active Balance BMS is capable of bidirection power transfer at each cell. Each EM1401EVM can manage 6 to 14 cells (60V max) for Li-ion battery applications. The EM1401EVM modules can be stacked up to 1300V. The system provides fast cell balancing, diagnostics, and module to controller communication. Independent protection circuitry is also provided.
• 48Vin, 300W 1/8brick Digital Module with GaN FET Reference Design
  PMP4435.1: The PMP4435 is a DC-DC isolated digital module with GaN mosfet reference design targeted for industrial and telecom applications. The DC input range is 36V-60V, with 12V typical and the output is 12V/5A. An digital controller UCD3138A is used in the design. The efficiency is up to 95.8% with good thermal performance.
• 33W Offline QR Flyback Converter with Multiple Outputs Reference Design - PMP10020.1 - TI Tool Folder
  PMP10020: This design uses the UCC28610 quasi-resonant flyback controller to generate 3 isolated outputs from an universal input (90VAC - 290VAC). It was built on a low cost single layer PCB. The regulated output provides 12V@1.89A and the maximum output power is 33W.
• Non-Isolated Synchronous Buck (1.8V@8A)
  PMP7828.4: This is a synchronous buck converter design with an input voltage range of 10.8V-to-13.2Vin and four regulated outputs: 1Vout@24A, 1.5Vout@30A, 3.3Vout@6.4A, and 1.8Vout@8A.
• 20W Industrial Power Supply - PMP10559 - TI Tool Folder
  PMP10559?SYS-null-null-findchips-refdes-rd-null-wwe: PMP10559 is a non-sync isolated Flybuck-boost converter with a negative primary voltage. The power supply has a synchronous buck regulator, LM5160, and a versa pack transformer. The design accepts an input voltage of 18V to 30V, and outputs 30V, capable of providing 0.67A of current to the load, making it suitable for 24V input industrial application. The Fly-Buck topology can regulate the secondary side outputs without opto-coupler or aux winding, and is capable of achieving good regulation within ±5%. With LM5160's Constan On-Time control, no loop compensation is required, which simplifies the design and helps reducing the external part count and BOM cost.
• Automotive Reverse Battery Protection Reference Design with Overcurrent and Overvoltage Shutoff - PMP9498 - TI Tool Folder
  PMP9498?SYS-null-null-findchips-refdes-rd-null-wwe: The PMP9498 reference design is a complete front-end protection solution for automotive systems needing reverse voltage, over-voltage, and over-current protection. Load switch capability is also implemented to digitally control the connection and disconnection of the load to the input supply. The design meets the low Iq requirements for automotive applications during shutoff and features a strong gate current source (typ 30 mA) to drive high power MOSFETs for high current applications.
• 35V to 60V Input, 600W Output Dual-Phase Synchronous Buck Converter with Greater than 97% Efficiency - PMP7282 - TI Tool Folder
  PMP7282?SYS-null-null-findchips-refdes-rd-null-wwe: This 600W wide voltage input dual phase power converter uses two emulated current-mode controllers 180 degrees out of phase to minimize input and output ripple current. Compared to conventional isolated power converters, this synchronous buck architecture provides a reduced footprint and BOM cost at higher levels of efficiency, greater than 97% over several operating conditions.
• 9 to 42Vin 5V/12V/20V @ 5A Synchronous 4-Switch Buck-Boost Converter Reference Design
  PMP10698.2: PMP10698 is a synchronous 4-switch buck-boost converter which utilizes the LM5175 controller for USB type C applications. The output voltage can be selected for 5V, 12V or 20V at 5A using jumpers or open drain control switches. The LM5175 average current loop sets a maximum output current of 6.25A.
• 200VAC-400VAC Input, 24V 50W Output, PSR Flyback with SiC-FET Reference Design
  PMP10416: This design uses low-cost primary side regulation (PSR) IC UCC28700 with a SiC-FET for 200VAC-400VAC input range. A 24V output is generated with maximum 50W rating.
• 15W Isolated Downlight / light bulb LED Driver (32V @ 0.4A) - PMP8011 - TI Tool Folder
  PMP8011?SYS-null-null-findchips-refdes-rd-null-wwe: The main purpose of this reference design is to demonstrate a high performance offline flyback LED driver with PFC based on TPS92314A (220VAC with PFC) . This LED driver is designed for converting an AC input to a regulated LED current. The operating conditions and performance of the reference design are as follows: 198VAC to 264VAC, 50Hz Input Voltage, 28V to 34V LED Voltage, 400mA Regulated LED Current , 87% Typical System Efficiency, High Power Factor > 0.9, Output Short-Circuit and Open-Circuit Protection.
• Dual Sensor Measurement Using Single Current-Loop with FSK Modulation Reference Design
  TIDA-00483: The TIDA-00483 reference design brings together several devices to create a subsystem capable of measuring the surrounding environment and communicating the temperature, humidity, and ambient light over a 4- to 20-mA current loop. The small foot print of the design contains all sensors, filters, and control circuitry to calculate and communicate the sensor data. The reference design is intended for process measurement applications in factory automation, field transmitters, and building automation. The sensors, MCU, and communication modules all run off power from the current loop, which requires less than 3.5 mA to achieve. This power configuration allows the rest of the current to be dynamically adjustable for the 4- to 20-mA loop communication protocol standard.
• 2.2MHz Switching, Synchronous Split Supply Reference Design for 12V Battery with all Protections - PMP10651.4 - TI Tool Folder
  PMP10651: PMP10651 is a low noise, multi-output SMPS design where LM53603 is used in Inverting Buck-Boost Fly buck topology to generate positive and negative supply needed in multiple noise sensitive applications such as powering High Speed Video Amplifier, RF amplifier, Precision Low noise amplifier etc. The design accepts an input voltage of 7Vin to 15 Vin DC (from 12V Lead Acid Battery) and provides outputs of +12V@500mA, -12v@500mA, 5V @400mA and 3.3V@150mA. It features a small size and is an inexpensive and more efficient solution to using Flyback or Pushpull converters .
• 310W PSU Using Transition Mode Bridgeless PFC and LLC-SRC - Reference Design - PMP9640 - TI Tool Folder
  PMP9640?SYS-null-null-findchips-refdes-rd-null-wwe: High efficiency, high power factor and reliable power supply are the main focus of the PMP9640 design for motor driver applications. Low cost analog transition mode (TM) PFC controller UCC28051 has been used for bridgeless PFC as the first conversion stage of the PMP9640. LLC series resonant converter (SRC) with UCC25600 is applied as the second stage of the PMP9640. In addition, a high-side buck converter with UCC28710 is applied here as the bias supply. In this design, bridgeless PFC efficiency can go up to 98.5%.
• Self or Dual-Powered Supply for Protection Relay, MCCBs & ACBs Ref Design
  TIDA-00229: This power supply solution for Protection Relays & MCCBs handles both the current input from a Current Transformer (CT) or input from an Auxillary (Aux) source. The "self-powered" capability comes from being able to harness the power available in the grid through the CT. The flexibility of this solution's "dual-power" input comes from the ability to also handle the Aux input - which is often a battery source.
• Linear Regulator as a Dynamic Voltage Scaling Power Supply Reference Design - TIDA-00531 - TI Tool Folder
  TIDA-00531?SYS-null-null-findchips-refdes-rd-null-wwe: The TIDA-00531 reference design features dynamic voltage scaling (DVS) as a power management solution to power CPU/DSP core voltages.
• 24V/12W Off-Line DCM Flyback Converter Optimized for Zero-Power at No-Load
  PMP10927: This design features the UCC28730 flyback controller in conjunction with the UCC24650 Wake-Up monitor to provide CV, CC regulated output with ultra-low stand-by power that exceeds Level VI and CoC Tier 2 specifications for average efficiency and 10% load efficiency. Wake-up signal detection provides fast transient response to large load steps. As seen at APEC
• System Level Power Reference Design for 20W ADAS system with Automotive Protections
  PMP10750: PMP10750 is a System optimized (CISPR 25 Class 5) 20W design for upstream converter used in ADAS system with automotive protection. The design has various protections such as Load dump through TVS (ISO pulse testing), Reverse Voltage (Innovative Smart diode with very low Iq), Battery Disconnect Switch with OVP protection (PFET) and is EMI optimized to meet Conductive EMI limits of CISPR25 Class5. Input voltage range is between 4.5V to 30V with OVP at 20V and hence will operate in wide input voltage conditions. LM74610 is used for Battery reverse protection which utilizes a charge pump to drive an N-channel FET to provide a resistive path for the bypass current to flow. LM53603Q1 is used as front end DC/DC Buck converter which is 2.2MHz switching, Synchronous rectified Wide Vin Buck Converter which can take transient up to 42V.
• Isolated offline LED driver with 120V AC and driving 4X4 LED string at 1.5A - PMP7753 - TI Tool Folder
  PMP7753?SYS-null-null-findchips-refdes-rd-null-wwe: 120Vac Isolated Offline Flyback AC to DC converter with constant current Feedback for driving 4 LEDs at 1.5A. Also implemented is a simple circuit to decode a dimming signal from a TRIAC, This dimming decoder circuit, controls the dimming level of the LEDs.
• Non-Synchronous Boost with Triple Outputs (10.6V@.1A)
  PMP7833.2: This is a non-synchronous boost converter with an input voltage range of 4.5V-to-5.5Vin and three regulated outputs: 12Vout @ 0.15A, 10.6Vout @ 0.1A, and 3.3Vout @ 0.03A
• Primary-Side Regulated Flyback with 85 to 265VAC Input (12V @ 0.5A) Reference Design
  PMP8787: The PMP8787 reference design uses the UCC28700 flyback controller to generate a 12V/500mA output from a univeral AC input. The primary-side regulation technique implemented by the UCC28700 eliminates the need for an opto coupler, reducing the size and cost of the design. In addition, the valley switching of the UCC28700 allows this design to achieve a maximum load efficiency over 80%; no load losses are less than 40mW. The circuit board measures only 28mm by 33mm, with a maximum height below 20mm.
• Voltage-Mode Multiplying DAC Reference Design - TIPD159 - TI Tool Folder
  TIPD159?SYS-null-null-findchips-refdes-rd-null-wwe: This multiplying DAC (MDAC) circuit creates a unipolar voltage output from 0 V to 2.5 V. This design does not require dual supplies to realize a unipolar, positive output voltage as with typical MDAC circuits. This design removes the need for a negative rail by using the MDAC in “reverse” to form a binary weighted voltage divider.
• Wide Vin Low Noise Triple Output Step Down Converter Reference Design - PMP9462 - TI Tool Folder
  PMP9462?SYS-null-null-findchips-refdes-rd-null-wwe: The reference design PMP9462 is a single input step-down converter with three low-noise outputs. The module uses LM43603, a synchronous step-down DC-DC converter capable of driving up to 3A of load current from an input voltage ranging 7V to 36V. The 5V output from LM43603 enables the LM26420 which further steps down this voltage to produce 1.8V and 2.5V outputs, capable of driving 1A load current each. This power supply is suitable for applications that require multiple outputs from a single input DC voltage. It provides good regulation performance over an input voltage range of 7V to 36V.
• Non-Synchronous Flyback converter with dual-output (-5V@.25A)
  PMP7901.2: PMP7901 is a Non-Synchronous Flyback converter with an input of 8 volts to 18 volts. It has an isolated dual-output of 5 volts and negitive 5 volts at 0.25 Amps.
• Digitally Isolated 2-Channel, Wide DC Binary Input Module Reference Design
  TIDA-00420: This reference design enables translation of high DC voltage inputs upto 300VDC into binary logic level voltages that a typical electronic circuit can handle. This solution is very flexible, not only handling input voltages from 18 to 300VDC but also allowing programmable switching thresholds to set binary levels. In addition, this solution enables < ± 3.0% (± 1V measured value step size) error in voltage detection coupled with reliable isolation > 2kV RMS.
• 12- to 24-V, 27-A Brushed DC Motor Reference Design
  TIDA-00620: Brushed motors are a relatively popular option for motor designs because of their low price and simple control scheme. A brushed motor has a wire-wound rotor and permanent magnet stator. The commutation of the motor is achieved using conductive rings that are connected to the rotor using brushes that scrape against the commutator rings. This allows the direction of current through the motor to change based on the orientation of the brushes and different commutation rings. Utilizing an H-Bridge allows for easy direction and speed control changes to be applied quickly and efficiently to the brushed DC motor. An electronic drive is required to control the motor currents in a brushed DC motor. The electronic drive circuit consists of a power stage with two-phase inverter meeting the required power capability, a microcontroller to implement the motor speed commands and fault handling, current sensing for motor startup / stall protection, gate driver for controlling the two-phase inverter, and a power supply for microcontroller and other low voltage devices.
• 14Vin to 15.5Vin, 24Vout @ 8A Synchronous Boost Converter Reference Design - PMP9386 - TI Tool Folder
  PMP9386?SYS-null-null-findchips-refdes-rd-null-wwe: PMP9385 is a synchronous dual-phase boost converter accepts an input voltage of 14V to 15.5V, and outputs 24V, capable of providing 8A of current to the load.
• 56W Active Clamp for Telecom Apps Reference Design
  PMP10202: This reference design provides 28V out of 48V input voltage to supply noise sensitive loads
• CISPR 25 Class 5 Rated 10 W Reference Design for Automotive USB Charger System - PMP9496.1 - TI Tool Folder
  PMP9496: The PMP9496 reference design is a conducted EMI-optimized (CISPR 25 Class 5) 10 W design for efficient automotive USB charger application utilizing the LM53603 regulator IC (2.1MHz fully-integrated synchronous buck for automotive application ) and TPS2549 USB switch(TPS2549-Q1 Automotive USB Charging Port Controller with Integrated Power Switch & Cable Compensation). The design accepts wide input voltage range of 7Vin to 25Vin and provides the outputs of 5V@2.1A. It features a small size and is an inexpensive and more efficient solution customized for automotive USB charger application. The board dimension of the PMP9496 PCB is 2800mil * 4000mil. Four layer PCB was used for the design.
• 9 to 42Vin 5V/12V/20V @ 5A Synchronous 4-Switch Buck-Boost Converter Reference Design
  PMP10698.1: PMP10698 is a synchronous 4-switch buck-boost converter which utilizes the LM5175 controller for USB type C applications. The output voltage can be selected for 5V, 12V or 20V at 5A using jumpers or open drain control switches. The LM5175 average current loop sets a maximum output current of 6.25A.
• 14-Channel Active Cell Balance Battery Management Reference Design - TIDA-00239 - TI Tool Folder
  TIDA-00239?SYS-null-null-findchips-refdes-rd-null-wwe: Active Balance chipset for use in large format Lithium-ion batteries that provides monitoring, balancing, and communications. With precise and robust active balancing, the Active Balance BMS is capable of bidirection power transfer at each cell. Each EM1401EVM can manage 6 to 14 cells (60V max) for Li-ion battery applications. The EM1401EVM modules can be stacked up to 1300V. The system provides fast cell balancing, diagnostics, and module to controller communication. Independent protection circuitry is also provided.
• 48Vin, 300W 1/8brick Digital Module with GaN FET Reference Design
  PMP4435.6: The PMP4435 is a DC-DC isolated digital module with GaN mosfet reference design targeted for industrial and telecom applications. The DC input range is 36V-60V, with 12V typical and the output is 12V/5A. An digital controller UCD3138A is used in the design. The efficiency is up to 95.8% with good thermal performance.
• 24-V, 50-W BLDC Motor Sinusoidal Drive Reference Design for Air Purifier Fans - TIDA-00656 - TI Tool Folder
  TIDA-00656?SYS-null-null-findchips-refdes-rd-null-wwe: The TIDA-00656 reference design is a cost-effective, small form-factor (SFF), three-phase sinusoidal motor drive for brushless DC (BLDC) motor up to a power of 50 W at 24 V. The board accepts 24 V at the input and provides three motor outputs to drive the BLDC motor sinusoidally. By using a microcontroller (MCU), in this case the MSP430G2303, the speed loop is closed externally after accepting the speed command over IR (infra-red) sensor.
• Automotive Buck-Boost Power Solution Reference Design - PMP10170 - TI Tool Folder
  PMP10170?SYS-null-null-findchips-refdes-rd-null-wwe: PMP10170 provides a constant output voltage of 5.0V @ 500mA from an wide input voltage range of 4.0V up to 39.0V. It is working with a fixed switching frequency of 380 kHz but provides also the possibility to modulate the switching frequency to reduce the EMI.
• 24V/12W Off-Line DCM Flyback Converter Optimized for Zero-Power at No-Load - PMP10927 - TI Tool Folder
  PMP10927?SYS-null-null-findchips-refdes-rd-null-wwe: This design features the UCC28730 flyback controller in conjunction with the UCC24650 Wake-Up monitor to provide CV, CC regulated output with ultra-low stand-by power that exceeds Level VI and CoC Tier 2 specifications for average efficiency and 10% load efficiency. Wake-up signal detection provides fast transient response to large load steps. As seen at APEC
• Xilinx Virtex® UltraScale™ FPGA Multi-Gigabit Transceiver (MGT) Power Solution - PMP10520.3 - TI Tool Folder
  PMP10520: The PMP10520 reference design provides all the power supply rails (1V/20A, 1.2V/30A, 1.8V/4A) necessary to power the multi-gigabit transceivers (MGT) in Xilinx's Virtex® UltraScale™ FPGAs. This design uses a 5V input and has a PMBus interface for current and voltage monitoring, margining, timing delays, and fault monitoring. It uses both TPS544C20 and TPS544B20 which feature internal current sensing and eliminate the need for an external current sense resistor. This design also meets Xilinx's low output voltage ripple requirements of the MGT rails.
• Digitally Isolated 2-Channel, Wide DC Binary Input Module Reference Design - TIDA-00420 - TI Tool Folder
  TIDA-00420?SYS-null-null-findchips-refdes-rd-null-wwe: This reference design enables translation of high DC voltage inputs upto 300VDC into binary logic level voltages that a typical electronic circuit can handle. This solution is very flexible, not only handling input voltages from 18 to 300VDC but also allowing programmable switching thresholds to set binary levels. In addition, this solution enables < ± 3.0% (± 1V measured value step size) error in voltage detection coupled with reliable isolation > 2kV RMS.
• Synchronous Buck Converter for POL DC to DC Module Application Reference Design
  PMP9350: PMP9350 is a Constant On-Time synchronous buck regulator utilizing the LM5017 wide-vin with integrated HS and LS MOSFETs for industrial/automotive applications. This board was developed to fit into space-constrained applications. It also uses an external SS circuit for a reduced start-up time.
• Ultra-Small 1W, 12V-36V Iso Power Supply for Analog Prog Logic Controller Modules Reference Design - TIDA-00237 - TI Tool Folder
  TIDA-00237?SYS-null-null-findchips-refdes-rd-null-wwe: Analog input and output modules are a standard component in Programmable Logic Controllera (PLC) or Distributed Control Systems (DCS). More channels per module and slimmer modules bring design challenges to the isolated power supply in those modules. Anyone facing those challenges will benefit from TIDA-00237, as the total design foot print is less than 2.54x2.54mm and less than 5mm height. It uses a fly-buck approach which means no optocoupler feedback with wide input voltage range of 12V-36V. The design provides +/-15V and 5V isolated, low noise outputs optimal for driving a data converter or analog front end.
• 220W Synchronous 4 Switch Buck-Boost Converter - PMP9490 - TI Tool Folder
  PMP9490?SYS-null-null-findchips-refdes-rd-null-wwe: PMP9490 is a 225W four Switch Buck –Boost Design utilizing best in Class Synchronous Buck Boost Converter LM5175. The design accepts an input voltage of 9.5Vin to 20Vin and provides the outputs of 15V@15 A for Constant Voltage Output Application such as Voltage stabilizer or as Power amplifier SMPS, 10.8V to 15V@12.5A for CC/CV Battery Charger application, and 12.5 A for Constant Current LED Drive application. It features an inexpensive and more efficient solution to using discrete Buck and boost converters. The average current regulation loop of the IC at the output is used for Battery Charging profiling with no external circuit being involved.
• 335W Single Stage LLC-SRC Converter Reference Design
  PMP10375.2: The PMP10375 reference design is a single stage LLC series resonant converter (SRC), producing up to a 335W output using UCC25600 resonant controller. With the use of single stage LLC-SRC, the converter efficiency goes up to 90% at 335W full output power with 120VAC input.
• TPS92310 - 220VAC, 8W Isolated Flyback LED Driver with PFC - PMP8005 - TI Tool Folder
  PMP8005?SYS-null-null-findchips-refdes-rd-null-wwe: The main purpose of this reference design is to demonstrate a high performance and compact size offline flyback LED driver with PFC based on TPS92310. This LED driver is designed for converting an AC input to a regulated LED current. The operating conditions and performance of the reference design are as follows: ●198VAC to 264VAC, 50Hz Input Voltage ●18V to 22V LED Voltage ●350mA Regulated LED Current ●84% Typical System Efficiency ●0.9 Typical Power Factor ●Output Short-Circuit and Open-Circuit Protection
• 90 - 134VAc input with isolated Flyback, dual output USB chargers, and LDO Reference Design
  PMP10878.2: The PMP10878 is an isolated dual port USB charger powered from an AC source. This design allows for up to 36W of power delivery through both USB chargers and the secondary side of a flyback.
• 90 - 134VAc input with isolated Flyback, dual output USB chargers, and LDO Reference Design
  PMP10878.4: The PMP10878 is an isolated dual port USB charger powered from an AC source. This design allows for up to 36W of power delivery through both USB chargers and the secondary side of a flyback.
• High Efficiency, High Power Factor 1300W AC/DC Power Supply Reference Design - PMP10948.2 - TI Tool Folder
  PMP10948: PMP10948 is a high-efficiency, high power factor AC/DC power supply reference design using UCC28063 interleaved transition-mode PFC controllers. There are two PFC stages in this design, 750W output power generates from one of the PFC stages and 550W output power generates from the other PFC stage. This design achieve 95.6% efficiency at 120VAC input and 98% efficiency at 220VAC input with over 1300W output power.
• 144W Single-Phase Synchronous Boost Converter With DCR Current Sensing
  PMP9393: PMP9393 is a Single-Phase Synchronous Boost Converter which utilizes the LM5122 controller IC. The design accepts an input voltage of 18Vin to 20Vin and provides an output of 48Vout capable of supplying a maximum of 3A of current to the load. DCR current sensing has been implemented in order to reduce the BOM cost associated with using a high power current sense resistor.
• High Density Efficient Solution for Main Aux as well as Back up Aux Power in Drones - PMP10650.2 - TI Tool Folder
  PMP10650: PMP10650 is a high power density 40W Buck Converter design optimized for Wide Vin Drone Design using the LM3150 controller IC (Used for Drone’s Backup Power) and LM53603. The design accepts an input voltage of 7Vin to 36Vin and provides the outputs of 5V@5A for Drone’s Backup power and 5V@3A for Drone’s manpower. It features a small size and is an inexpensive and more efficient solution.
• CISPR 25 Class 5 Multi-Output Power Supply Reference Design for Rear Camera, Automotive ADAS Systems - PMP9492.2 - TI Tool Folder
  PMP9492: PMP9492 is a conducted EMI optimized (CISPR 25 Class 5) 9 W Multi output Design for Wide Range Vin automotive ADAS application that supports Cold –Cranking Conditions . The design uses an LM53603 regulator IC (used as Buck), LM26420 (used as dual Buck) and TPS60150 regulator IC (used as Charge pump for 5V output). The design accepts an input voltage of 4.5Vin to 20Vin and provides the outputs of 3.3V @ 1.0A, 2.5V @ 1.0A, 1.8V @ 1.0A, and 5V @ 100mA. It features a small size and is an inexpensive and more efficient solution customized for ADAS and other Automotive related applications. The Board dimension of PMP9492 PCB is 2600mil × 4000mil. Four layer PCB was used for the design.
• 40W Buck Converter Powered out of 48V Reference Design - PMP10135 - TI Tool Folder
  PMP10135?SYS-null-null-findchips-refdes-rd-null-wwe: PMP10035 is a sycnchronous buck converter with 48V input voltage and 31V output voltage. Due to ceramic capacitors only this design is suitable for automotive applications (48V bus). With switching frequency of 400kHz, the efficiency is higher than 96% at full load.
• Wide Vin Low Noise Triple Output Step Down Converter Reference Design
  PMP9462: The reference design PMP9462 is a single input step-down converter with three low-noise outputs. The module uses LM43603, a synchronous step-down DC-DC converter capable of driving up to 3A of load current from an input voltage ranging 7V to 36V. The 5V output from LM43603 enables the LM26420 which further steps down this voltage to produce 1.8V and 2.5V outputs, capable of driving 1A load current each. This power supply is suitable for applications that require multiple outputs from a single input DC voltage. It provides good regulation performance over an input voltage range of 7V to 36V.
• Universal Line Power Supply for PLC using PSR Flyback and Compact DC/DC Stages Reference Design
  PMP9185.4: The PMP9185 reference design uses the UCC28710 primary-side regulated flyback controller to generate a 15V output from a univeral AC input with maximum 20W output power followied by DC/DC and LDO stages using TPS54229 and TPS650250, and 5V, 3.3V, 1.8V and 1.2V are provided. A switch on the PCB provides the freedom of supplying DC/DC and LDO from AC input or DC input.
• 48V Vin Nominal, 100V Vout @ 1A Single-Phase Synchronous Boost Converter - PMP7933 - TI Tool Folder
  PMP7933?SYS-null-null-findchips-refdes-rd-null-wwe: PMP7933 is a single-phase synchronous boost converter using the LM5122 controller IC. The design accepts an input voltage of 48Vin +/-5% and provides an output voltage of 100Vout capable of supplying a maximum of 1A of current to the load. The design was built on the PMP7896 revB PCB.
• Quad Output Isolated Synchoronous Fly-Buckboost Converter Reference Design
  PMP10545: PMP10545 is an Isolated Flyback Converter with the primary configured as a buck-boost inverter, using the LM5160 regulator IC. The design accepts an input voltage of 9Vin to 30Vin and provides four isolated outputs of +5.7Vout, each capable of supplying 350mA. The design uses an easily available off-the-shelf transformer, making it a more cost effective design solution.
• 90 - 134VAc input with isolated Flyback, dual output USB chargers, and LDO Reference Design
  PMP10878.1: The PMP10878 is an isolated dual port USB charger powered from an AC source. This design allows for up to 36W of power delivery through both USB chargers and the secondary side of a flyback.
• Primary Side Regulated Flyback Reference Design with 120VAC Input and 24V/4A Rated Output
  PMP10804: This reference design implements the UCC28630 PSR controller in a flyback power supply. The UCC28630 is capable of operating in both Continuous and Discontinuous Conduction Modes which enables high efficiency while reducing inductor size and cost. Safety standards such as EN60950 require that any X-capacitors in EMC filters on the AC side of the bridge rectifier quickly discharge to a safe level when AC is disconnected. Typically, this requirement is achieved by including a resistive discharge element in parallel with the X-capacitor. However, this resistance causes a continuous power dissipation that impacts the standby power performance. In order to reduce standby power and eliminate the standing loss associated with the conventional discharge resistors, the UCC28630 device incorporates active X-capacitor discharge circuitry. In this design, less than 100mW no load power comsumption and over 88% converter efficiency is achieved.
• Single Stage 200W AC-DC LLC Series Resonant Conv for 120VAC & 230VAC Input Reference Design
  PMP10283: The PMP10283 reference design provides 30V/100W and -30V/100W outputs from AC line voltage to a single LLC resonant converter stage. This design is featured with its low circuit cost and high efficiency (over 90% @ 120VAC full load and ~92% @ 240VAC full load). This design uses the UCC25600 resonant converter controller for LLC resonant converter.
• Hercules Safety MCU Industrial Power Solution Reference Design
  PMP10189.2: This reference design is a complete power solution for the Hercules™ Safety MCU. The input voltage can be in the range of 48..60V and it provides five different output rails with 12.0V @ 30mA, 5.0V @ 240mA, 3.3V @ 620mA, 3.3V @ 230mA and 1.2V @ 700mA.
• AC Offline Converter Providing 5VDC or 12VDC Output at 2A - PMP7883.1 - TI Tool Folder
  PMP7883: The following design, driven by the LM5023, takes an AC input, like the ones located in the common US power outlet, and generates 5V/12V out, 2A DC signal, outputs commonly used for USB connections.
• Four-Output, Flybuck and Buck Converter for High Performance Computing Reference Design - PMP10837.2 - TI Tool Folder
  PMP10837: The PMP10837 reference design offers dual output rails for use in enterprise computing. This design implements an isolated step down design, with non-isolated converters on both the primary and secondary side.
• High Efficiency 400W AC/DC Power Supply Reference Design - PMP11064.2 - TI Tool Folder
  PMP11064: PMP11064 is a high-efficiency AC/DC power supply reference design with universal AC input and 20V/20A output. Interleaved transition mode PFC and LLC series resonant converter is applied for 20V/20A main power. A PSR Flyback with MOSFET integrated controller is applied as the auxiliary supply. 91.2% efficiency is achieved at low line and full load. 93.1% efficiency is achieved at high line and full load.
• Battery Powered Boost Converter Delivers 120Vdc @ 10mA Reference Design
  PMP8956: This design is driven by the LM3481. The LM3481 is a versatile Low-Side N-FET high performance controller for switching regulators. The switching frequency of the LM3481 can be adjusted to any value between 100 kHz and 1 MHz by using a single external resistor or by synchronizing it to an external clock. The LM3481 has built in protection features such as thermal shutdown, short-circuit protection and over voltage protection. Power saving shutdown mode reduces the total supply current to 5µA and allows power supply sequencing.
• Ultrasonic Water Flow Meter Design using Time to Digital Conversion - TIDM-ULTRASONIC-FLOW-TDC - TI Tool Folder
  TIDM-ULTRASONIC-FLOW-TDC?SYS-null-null-findchips-refdes-rd-null-wwe: The TIDM-ULTRASONIC-FLOW-TDC is a reference design for an ultrasonic flow meter (water, gas or heat meter) with LCD built using a Time-to-Digital converter and an ultra-low power MCU. Solution includes optimized leakage detection, low power consumption, and a small form factor that are important requirements for water, heat and gas meter applications. This design also includes a high efficiency DC-DC converter for system power.
• Hercules Safety MCU Industrial Power Solution Reference Design
  PMP10189.5: This reference design is a complete power solution for the Hercules™ Safety MCU. The input voltage can be in the range of 48..60V and it provides five different output rails with 12.0V @ 30mA, 5.0V @ 240mA, 3.3V @ 620mA, 3.3V @ 230mA and 1.2V @ 700mA.
• 4-Switch Buck-Boost Delivers High Transient Power for Wireless Base Station Reference Design
  PMP9104: This four switch buck-boost converter functions as both a buck or a boost, with a smooth transition between modes. It delivers a 28V (typical) output voltage at 2-3A continuous (4.5A peak) from a 22V-32V input.
• Primary-Side Regulated Flyback with 85 to 265VAC Input (12V @ 0.5A) Reference Design - PMP8787 - TI Tool Folder
  PMP8787?SYS-null-null-findchips-refdes-rd-null-wwe: The PMP8787 reference design uses the UCC28700 flyback controller to generate a 12V/500mA output from a univeral AC input. The primary-side regulation technique implemented by the UCC28700 eliminates the need for an opto coupler, reducing the size and cost of the design. In addition, the valley switching of the UCC28700 allows this design to achieve a maximum load efficiency over 80%; no load losses are less than 40mW. The circuit board measures only 28mm by 33mm, with a maximum height below 20mm.
• Non-Isolated Synchronous Buck used for Transportation and Automotive Applications - PMP7858 - TI Tool Folder
  PMP7858?SYS-null-null-findchips-refdes-rd-null-wwe: This is a synchronous buck converter with an input voltage range of 8V-to-16Vin (40Vin max) and a regulated output at 5Vout @ 1.5A.
• Non-Synchronous Flyback Converter with Dual-Output (5V@.25A)
  PMP7901.1: PMP7901 is a Non-Synchronous Flyback converter with an input of 8 volts to 18 volts. It has an Isolated dual-output of 5 volts and negitive 5 volts at 0.25 Amps.
• Four-Output, Flybuck and Buck Converter for High Performance Computing Reference Design
  PMP10837.2: The PMP10837 reference design offers dual output rails for use in enterprise computing. This design implements an isolated step down design, with non-isolated converters on both the primary and secondary side.
• 6.5V/2A Boost Converter Reference Design - PMP10026 - TI Tool Folder
  PMP10026?SYS-null-null-findchips-refdes-rd-null-wwe: This reference design provides an output voltage of 6.5V from an input voltage range of 3V to 6.5V.
• Non-Isolated Synchronous Buck Converter (1V@24A)
  PMP7828.1: This is a synchronous buck converter design with an input voltage range of 10.8V-to-13.2Vin and four regulated outputs: 1Vout@24A, 1.5Vout@30A, 3.3Vout@6.4A, and 1.8Vout@8A.
• CISPR 25 Class 5 Rated 10 W Reference Design for Automotive USB Charger System
  PMP9496.2: The PMP9496 reference design is a conducted EMI-optimized (CISPR 25 Class 5) 10 W design for efficient automotive USB charger application utilizing the LM53603 regulator IC (2.1MHz fully-integrated synchronous buck for automotive application ) and TPS2549 USB switch(TPS2549-Q1 Automotive USB Charging Port Controller with Integrated Power Switch & Cable Compensation). The design accepts wide input voltage range of 7Vin to 25Vin and provides the outputs of 5V@2.1A. It features a small size and is an inexpensive and more efficient solution customized for automotive USB charger application. The board dimension of the PMP9496 PCB is 2800mil * 4000mil. Four layer PCB was used for the design.
• 360W Phase Shift Full Bridge Resonant LLC with High Side Low Side Driver Reference Design
  TIDA-00381: The power supply employs Full Bridge Resonant LLC with phase shift operating at ramp up, light load, low output voltage. This operating mode can replace PWM operating mode in LLC, which can improve efficiency signficantly in light load.
• Multi-Cell Battery Manager Unit with Integrated Charging, Gauging, Authentication and Protection - TIDA-00553 - TI Tool Folder
  TIDA-00553?SYS-null-null-findchips-refdes-rd-null-wwe: The Texas Instruments bq40z60 device is a Battery Pack Manager that integrates battery charging control output, gas gauging, and protection for completely autonomous operation of 2-series to 4-series cell Li-Ion and Li-Polymer battery packs. The architecture enables internal communication between the fuel gauging processor and battery charger controller to optimize the charging profile based on the external load conditions and power path source management during load transients and adaptor current limitations in the system. The charging current efficiency is scalable for power transfer based on the external components, such as the NFETs, inductor, and sensing resistor.
• Automotive Low Voltage SEPIC Stage Converts 4V…40Vin to 12Vout@2.5A Reference Design
  PMP10111: This small SEPIC converter accepts a wide input voltage range, 4V...40V, from automotive battery and supports the cranking phase. Vout is kept stable thank to the SEPIC topology. During cranking the input voltage can reach vaules as low as 4V. Extensive testing with a source generator have been performed.
• 48Vin, 300W 1/8brick Digital Module with GaN FET Reference Design
  PMP4435.5: The PMP4435 is a DC-DC isolated digital module with GaN mosfet reference design targeted for industrial and telecom applications. The DC input range is 36V-60V, with 12V typical and the output is 12V/5A. An digital controller UCD3138A is used in the design. The efficiency is up to 95.8% with good thermal performance.
• Automotive Power Supply with Pre-Boost Reference Design - PMP10223.4 - TI Tool Folder
  PMP10223: The PMP10223 automotive power reference design provides 5.0V @ 1.1A, 3.3V @ 0.6A and 1.3V at 1.0A. A pre-boost provides 9.0V @ 1.7A to ensure proper operation even during startup of the engine. A synchronous buck converters generates 6.0V @ 2.2A as an intermediate rail for the following buck converters.
• Xilinx Virtex® UltraScale™ FPGA Multi-Gigabit Transceiver (MGT) Power Solution - PMP10520.2 - TI Tool Folder
  PMP10520: The PMP10520 reference design provides all the power supply rails (1V/20A, 1.2V/30A, 1.8V/4A) necessary to power the multi-gigabit transceivers (MGT) in Xilinx's Virtex® UltraScale™ FPGAs. This design uses a 5V input and has a PMBus interface for current and voltage monitoring, margining, timing delays, and fault monitoring. It uses both TPS544C20 and TPS544B20 which feature internal current sensing and eliminate the need for an external current sense resistor. This design also meets Xilinx's low output voltage ripple requirements of the MGT rails.
• Isolated RS-485 to Wi-Fi Bridge with 24 VAC Power Reference Design
  TIDA-00486: The TIDA-00486 TI Design uses Texas Instruments SimpleLink Wi-Fi CC3200 Internet-on-a-chip Wireless MCU module to create a data bridge between an RS-485 network and a Wi-Fi network. An ISO15 transceiver provides an isolated RS-485 interface with up to 2500 VRMS of isolation. The LM5160 Fly-Buck™ power supply provides both isolated and non-isolated 3.3 V outputs for the two portions of the circuit. The design can be powered with AC or DC power up to 30 VRMS or 48 V peak A version of this design with a non-isolated RS-485 interface is presented in TIDA-00485.
• Non-Isolated RS-485 to Wi-Fi Bridge with 24 VAC Power Reference Design - TIDA-00485 - TI Tool Folder
  TIDA-00485?SYS-null-null-findchips-refdes-rd-null-wwe: The TIDA-00485 TI Design uses Texas Instruments SimpleLink Wi-Fi CC3200 Internet-on-a-chip Wireless MCU module to create a data bridge between an RS-485 network and a Wi-Fi network. An SN65HVD72 transceiver provides the RS-485 Interface with 12 kV of ESD protection, and additional protection is provided on board. The design can be powered with AC or DC power up to 30 V RMS or 48 V peak. A version of this design with an isolated RS-485 interface is presented in TIDA-00486.
• UPOE High-Efficiency Flyback Converter (12V/3.8A) Reference Design for PoE PD Applications
  TIDA-00741: TIDA-00741 uses two TPS2378 PD controllers for a forced 4-pair UPOE solution to 51W non-standard PoE PD applications. It incorportates the UCC2897A controller in a high-efficiency, great transient response (driven) synch flyback converter capble of 12V at 3.8A.
• BeagleBone Cape for Programmable Logic Controller Reference Design - TIDA-00312 - TI Tool Folder
  TIDA-00312?SYS-null-null-findchips-refdes-rd-null-wwe: The BeagleBone Black (BBB) Cape for the PLC I/O module is a platform for evaluation of the PLC I/O reference designs (ex. TIDA-00236). The platform showcases TI’s system solution that can be used in a PLC signal chain and allows evaluation of the signal chain performance. The cape connects the PLC I/O reference design daughter card (ex. TIDA-00236) to the BBB board. The BBB board runs the evaluation software for the I/O card and a webserver, allowing the user to view the performance from a PC. The highlight of this design is the simple hardware and minimal software installation requirements on the PC for evaluation. TI’s PLC I/O module reference designs have complete signal chain for the PLC I/O modules. Evaluating the signal chain requires examination of the critical performance parameters of the hardware. Data collection, processing, and display are the typical functions required for evaluation. The easy-to-use GUI accelerates the performance of the I/O module evaluation process and reduces time to market.
• High-Efficiency Low Vin 30W Boost Converter for Automotive Applications (E-Call) Reference Design
  PMP9382: PMP9382 is a low Vin boost converter utilizing the automotive grade LM3478Q-Q1 controller. This design starts at a diode drop above the minimum input voltage of 2.97V (~3.4V) to a maximum of 6V in. Once the power supply is enabled and output is present, this design will work down to 2V input minimum, supplying an output voltage of 10V at 3A. The Switching frequency is set to 400 kHz.
• Universal Line Power Supply for PLC using PSR Flyback and Compact DC/DC Stages Reference Design - PMP9185 - TI Tool Folder
  PMP9185?SYS-null-null-findchips-refdes-rd-null-wwe: The PMP9185 reference design uses the UCC28710 primary-side regulated flyback controller to generate a 15V output from a univeral AC input with maximum 20W output power followied by DC/DC and LDO stages using TPS54229 and TPS650250, and 5V, 3.3V, 1.8V and 1.2V are provided. A switch on the PCB provides the freedom of supplying DC/DC and LDO from AC input or DC input.
• Dual Sensor Measurement Using Single Current-Loop with FSK Modulation Reference Design - TIDA-00483 - TI Tool Folder
  TIDA-00483?SYS-null-null-findchips-refdes-rd-null-wwe: The TIDA-00483 reference design brings together several devices to create a subsystem capable of measuring the surrounding environment and communicating the temperature, humidity, and ambient light over a 4- to 20-mA current loop. The small foot print of the design contains all sensors, filters, and control circuitry to calculate and communicate the sensor data. The reference design is intended for process measurement applications in factory automation, field transmitters, and building automation. The sensors, MCU, and communication modules all run off power from the current loop, which requires less than 3.5 mA to achieve. This power configuration allows the rest of the current to be dynamically adjustable for the 4- to 20-mA loop communication protocol standard.
• Power Solution for an Automotive Fuel Injector
  PMP7966: PMP7966 is a 4-phase boost converter rated for 52V output at 2.5A from an input voltage of 6V to 42V. This design uses LM5122 boost controllers at a switching frequency of 100 kHz each phase, resulting in 400 kHz input and output ripple. 680μF aluminum electrolytic capacitors are used at the output of each phase, providing hold-up to support large transient currents.
• Ten Output QR Flyback and Buck Converter Reference Design
  PMP10822.5: The PMP10822 reference design utilizes two QR flyback, and four buck converters. The efficiency for the 12V and 24V flyback approaches 87%, while the 16V buck converter has efficiency greater than 89%.
• 40 V to 400 V Uni-directional Current/Voltage/Power Monitoring Reference Design - TIDA-00528 - TI Tool Folder
  TIDA-00528?SYS-null-null-findchips-refdes-rd-null-wwe: This verified design can accurately measure current, voltage and power on a bus as high as 400 V using an I2C- or SMBUS-compatible interface. This design is targeted towards industrial applications where there is a need to measure system current accurately with bus voltages greater than 40 Volts such as Solar inverters, HEV/EV systems and Source generation for AC/DC electronic loads and power sources. This is a low cost non-isolated solution for high voltage current monitoring. It uses INA226 and OPA333 along with a 600-V P-FET transistor.
• Two-Switch Buck-Boost Converter for 24W Wide Input - PMP7995 - TI Tool Folder
  PMP7995?SYS-null-null-findchips-refdes-rd-null-wwe: PMP7995 is a buck-boost converter rated for 12V output at 2A from an input voltage of 5V to 60V. This design uses the LM5118 buck-boost controller at a switching frequency of 300 kHz. To minimize cost the layout was done for a 2 layer printed circuit board.
• High Input Voltage Synchronous Buck Provides Two Independent Outputs of 28V at 2A and 16V at 4A
  PMP9227: The LM5119 controller allows the user to have two separate regulated outputs or the capability to combine the outputs (of the same voltage) into a two-phase regulator. This design operates from a 36V - 51V input and regulates 28V@2A (with transients up to 7A) and 16V@4A (with transients up to 6A).
• Flyback with Universal Input (85 - 264Vac), Dual Output 12V/2A and 3.3V/0.5A - PMP9638 - TI Tool Folder
  PMP9638?SYS-null-null-findchips-refdes-rd-null-wwe: The PMP9638 reference design uses the UCC28740 Flyback with resonant-ring valley-switching controller to generate dual DC output 12V/2A and 3.3V/0.5A from a universal AC input. This design minimize switching loss in FET to provide high efficiency. The current regulation feature of the UCC28740 provides accurate current limit protection.
• Analog Input Module for Industrial Outputs and Temperature Sensors Reference Design
  TIPD164: This TI Designs, Precision Verified design implements an analog input module for industrial voltages, currents, and temperature sensors. For industrial outputs, the possible input ranges include: 4-20 mA, 0-20 mA, +/-25 mA, 0-5 V, 0-10 V, +/-5 V, +/-10 V. The design includes conditioning and level-shift circuitry which converts the large industrial outputs into a proper input range for a +5V delta-sigma ADC. The ADC has features to directly acquire information from the RTD and thermocouple sensors over their full temperature range.
• 4-Channel LED Spotlight Driver Reference Design - PMP10171 - TI Tool Folder
  PMP10171?SYS-null-null-findchips-refdes-rd-null-wwe: The PMP10171 reference design is a boost LED driver with four outputs. It has an input voltage range of 10 .. 30V and provides 500mA at 40V maximum. A microcontroller provides an adjustable PWM signal for adjusting the brightness of the LEDs.
• Isolated Fly-Buck Power Module for PoE Application Reference Design - PMP10572 - TI Tool Folder
  PMP10572?SYS-null-null-findchips-refdes-rd-null-wwe: The PMP10572 reference design is an single output isolated Fly-Buck power supply for PoE application. It takes 48V nominal input and provides 12V 1A output. The board is designed with TPS2378(PD controller) to provide 40V-57V input votlage and 12V 1SA output power. The design features the LM5160A synchronous buck converter configured as a Fly-Buck regulator. With the benefit of primary side regulation, the supply has the outputs regulated without the opto-coupler or additional transformer winding. The LM5160A has a wide Vin range of 4.5V to 65V and 1.5A output current capability with integrated switch FETs. The input voltage to the reference board can be loosely regulated with a range of 40V to 57V.
• 35V to 60V Input, 600W Output Dual-Phase Synchronous Buck Converter with Greater than 97% Efficiency
  PMP7282: This 600W wide voltage input dual phase power converter uses two emulated current-mode controllers 180 degrees out of phase to minimize input and output ripple current. Compared to conventional isolated power converters, this synchronous buck architecture provides a reduced footprint and BOM cost at higher levels of efficiency, greater than 97% over several operating conditions.
• Power Solution for an Automotive Fuel Injector - PMP7966 - TI Tool Folder
  PMP7966?SYS-null-null-findchips-refdes-rd-null-wwe: PMP7966 is a 4-phase boost converter rated for 52V output at 2.5A from an input voltage of 6V to 42V. This design uses LM5122 boost controllers at a switching frequency of 100 kHz each phase, resulting in 400 kHz input and output ripple. 680μF aluminum electrolytic capacitors are used at the output of each phase, providing hold-up to support large transient currents.
• Triple Output Isolated Fly-Buck Power Supply for Industrial Application Reference Design
  PMP10516.1: PMP10516 is an Isolated Flybuck Converter using the LM25017 regulator IC. The design accepts an input voltage of 20.4Vin to 28.8Vin (40Vin Max. Peak) and provides three isolated outputs. The +5Vout rail is regulated for precision using the LP2951 linear regulator.
• 300-W PFC plus Resonant LLC Half-Bridge controller off-line AC/DC PSU Module
  TIDA-00520: This is a high efficiency 300-W AC/DC reference design. The design can be biased from external supply or configured for Self-Bias Auxillary mode for operation directly off the AC mains. The PFC is fully internally compensated, reducing design complexity and pcb design. Protections include 3-level OCP, line brown-out, PFC Bulk OVP plus UVP and OTP.
• High Density Efficient Solution for Main Aux as well as Back up Aux Power in Drones
  PMP10650.1: PMP10650 is a high power density 40W Buck Converter design optimized for Wide Vin Drone Design using the LM3150 controller IC (Used for Drone’s Backup Power) and LM53603. The design accepts an input voltage of 7Vin to 36Vin and provides the outputs of 5V@5A for Drone’s Backup power and 5V@3A for Drone’s manpower. It features a small size and is an inexpensive and more efficient solution.
• 20W 3-Phase E-Meter Flyback Reference Design - PMP10129.1 - TI Tool Folder
  PMP10129: The PMP10129 has been designed especially for E-meters. It uses the LM5021 flyback controller to provide two isolated outputs (6V and 24V) from an 3-phase input. The input voltage range is between 90VAC and 460VAC.
• Inverting Buck Boost Power Module Reference Design
  PMP10638: The PMP10638 reference design is a -5.2V 4A output power supply using SIMPLE SWITCHER® LMZ31710 Power Module. The reference design takes advantage of the small package and high level integration of LMZ31710 to achieve small solution size. It can support -5.2V 4A output power from 3.1V-3.3V input range. The working frequency is set to 1Mhz and very small ripple voltage.
• Xilinx Virtex® UltraScale™ FPGA Multi-Gigabit Transceiver (MGT) Power Solution with PMBus
  PMP10520.1: The PMP10520 reference design provides all the power supply rails (1V/20A, 1.2V/30A, 1.8V/4A) necessary to power the multi-gigabit transceivers (MGT) in Xilinx's Virtex® UltraScale™ FPGAs. This design uses a 5V input and has a PMBus interface for current and voltage monitoring, margining, timing delays, and fault monitoring. It uses both TPS544C20 and TPS544B20 which feature internal current sensing and eliminate the need for an external current sense resistor. This design also meets Xilinx's low output voltage ripple requirements of the MGT rails.
• 33W Offline QR Flyback Converter with Multiple Outputs Reference Design
  PMP10020.2: This design uses the UCC28610 quasi-resonant flyback controller to generate 3 isolated outputs from an universal input (90VAC - 290VAC). It was built on a low cost single layer PCB. The regulated output provides 12V@1.89A and the maximum output power is 33W.
• Complete Front End Automotive Reverse Polarity and Series Fault Protection Reference Design - PMP10748 - TI Tool Folder
  PMP10748?SYS-null-null-findchips-refdes-rd-null-wwe: PMP10748 is a complete automotive front end protection TIDesign that highlights TI's zero IQ Smart Diode Controller and High-Side Protection Controller. This design uses two LM74610-Q1 IC's to drive 40V MOSFETs in OR-ing Configuration for reverse polarity protection. The LM74610-Q1 is highly effective zero IQ replacement of lossy diodes and less effective PFET solutions for revere polarity protection. This design also includes programmable OVP, UVLO and OCP with LM5060-Q1 high side protection controller. This device also provides controlled rise time for safe connection and programmable fault detection delay time with LM5060-Q1
• System Level reference design for 30W ADAS system with required Automotive Protections
  PMP10652.7: PMP10652 is a System optimized (CISPR 25 Class 3) 30W design for Surround View ADAS system. The design has various protections such as Load dump through TVS (ISO pulse testing), Reverse Voltage (Innovative Smart diode with very low Iq), Battery Disconnect Switch with OVP protection (PFET) and is EMI optimized to meet Conductive EMI limits of CISPR25 Class3 (overall) and Class5 upto 30MHz Range. Input voltage range is between 4.5V to 30V with OVP at 20V and hence will operate in most Cold Cranking conditions. LM74610 is used for Battery reverse protection which utilizes a charge pump to drive an N-channel FET to provide a resistive path for the bypass current to flow. LM53603Q1 is used as front end DC/DC Buck converter which is 2.2MHz switching, Synchronous rectified Wide Vin Buck Converter which can take transient upto 42V. TPS57114Q1 is used to provide power to the cores and it is a high current 2,2MHz switching buck converter. LM26420 is a dual 2.2MHz switching buck converter which is used for generating other required supplies. LM3880 sequencer is used for all the power up and power down sequencing requirements.
• Automotive Power Supply with Pre-Boost Reference Design
  PMP10223.3: The PMP10223 automotive power reference design provides 5.0V @ 1.1A, 3.3V @ 0.6A and 1.3V at 1.0A. A pre-boost provides 9.0V @ 1.7A to ensure proper operation even during startup of the engine. A synchronous buck converters generates 6.0V @ 2.2A as an intermediate rail for the following buck converters.
• 40W SEPIC Conv w/Dual-Inductor High Efficiency Operating w/Automotive Input Range Reference Design - PMP9184C - TI Tool Folder
  PMP9184C?SYS-null-null-findchips-refdes-rd-null-wwe: This dual-inductor 13.2V@3A SEPIC converter achieves greater than 92% efficiency. It utilizes all surface mount components, maintains a low temperature rise and is capable of high peak load transients.
• Voltage-Mode Multiplying DAC Reference Design
  TIPD159: This multiplying DAC (MDAC) circuit creates a unipolar voltage output from 0 V to 2.5 V. This design does not require dual supplies to realize a unipolar, positive output voltage as with typical MDAC circuits. This design removes the need for a negative rail by using the MDAC in “reverse” to form a binary weighted voltage divider.
• 9 to 60Vin 12Vout @ 5A Single-Phase Isolated Synchronous Flyback Converter Reference Design
  PMP9256: PMP9256 is an isolated synchronous flyback converter utilizing the LM5122 for industrial applications. The benefit of using a synchronous flyback is higher efficiency compared to a non-synchronous flyback.
• 15W Automotive Start Stop Power Supply
  PMP9476: PMP9476 is non-sync buck converter plus a non-sync boost controller accepts an input voltage of 3.5V to 40V, and outputs 5V, capable of providing 3A of current to the load.
• 3-42Vin, 5V at 3A Buck-Boost Optimized for Automotive Cold Crank Reference Design - PMP10681 - TI Tool Folder
  PMP10681?SYS-null-null-findchips-refdes-rd-null-wwe: This is a modified LM5118 2 switch buck-boost single inductor evaluation module (EVM) optimized to operate through automitive transients such as cold-crank. It is designed to provide 15W (5V, 3A) of output power with an input voltage range of 3V to 42V.
• Wide Bandwidth Optical Front-end Reference Design - TIDA-00725 - TI Tool Folder
  TIDA-00725?SYS-null-null-findchips-refdes-rd-null-wwe: This reference design implements and measures a complete 120MHz wide bandwidth optical front end comprising a high speed transimpedance amplifier, fully differential amplifier, and high speed 14-bit 160MSPS ADC with JESD204B interface. Hardware and software are provided to evaluate the performance of the system in response to high speed optical pulses generated from the included laser driver and diode for applications including optical time domain reflectrometry (OTDR).
• Two-Wire Interface to a HIPERFACE DSL Encoder Reference Design
  TIDA-00177: The TIDA-00177 reference design is an EMC compliant industrial interface to a two-wire HIPERFACE DSL encoder. Applications include industrial servo drives. The design features a 3.3-V supply RS485 transceiver and line termination and coupling for encoder power over RS485 as per HIPERFACE DSL specification. The design has been tested up to 100m cable length with an integrated cable, where the encoder’s two-wire twisted pair was integrated in the same motor cable. The encoder connector output is protected against over-voltage and short circuit to prevent damage to an encoder or during a cable short. The design features an industrial compliant 24-V input with wide range from 18-36V. A 3.3V I/O connector with logic signals for easy interface to a host processor with HIPERFACE DSL Master IP Core is made available.
• High Input Voltage Synchronous Buck Provides Two Independent Outputs of 28V at 2A and 16V at 4A - PMP9227.1 - TI Tool Folder
  PMP9227: The LM5119 controller allows the user to have two separate regulated outputs or the capability to combine the outputs (of the same voltage) into a two-phase regulator. This design operates from a 36V - 51V input and regulates 28V@2A (with transients up to 7A) and 16V@4A (with transients up to 6A).
• 12.5Vin to 15.5Vin, 24Vout @ 8A Synchronous Boost Converter Reference Design
  PMP9385: PMP9385 is a Single-Phase Synchronous Boost Converter which accepts an input voltage of 12.5Vin to 15.5Vin and provides an output of 24Vout capable of supplying a maximum of 8A of current to the load. Design uses an LM5122 Synchronous Boost controller and CSD18531Q5A FETs.
• 860W Dual Phase Synchronous Buck Converter in Quarter Brick Footprint - PMP9260 - TI Tool Folder
  PMP9260?SYS-null-null-findchips-refdes-rd-null-wwe: PMP9260 is a dual-phase synchronous buck converter utilizing the LM5119 dual synchronous buck controller I.C. The design accepts an input voltage of 33V to 60V and provides a 28V output capable of supplying 30A of current to the load. This represents a maximum power density design of 860W in a quarter brick footprint. The maximum component height is set by the Coilcraft VER2923-103 inductors at 0.875 in.
• Universal AC Input, 5V/10A/50W PSR Flyback Power Supply W/Rapid Load Transient Response Ref Design
  PMP10407: PMP10407 is a quasi-resonant Flyback power suppy based on the UCC28730 primary side regulation (PSR) controller demonstrating the use of wake up device UCC24650 to achieve rapid load transient response from light load condition when the system is under low frequency operation. The elimination of optocoupler using PSR topology promises higher reliability and lower system cost. The design achieves less than 50mW standby power losses and over 86% efficiency at 25% load. The design also features UCC24610 synchronous rectification controller and demonstrates the use of UCC24650's ENS pin output to enforce diode rectification at light load conditions to reduce stand-by power losses.
• CISPR 25 Class 5 Multi-Output Power Supply Reference Design for Rear Camera, Automotive ADAS Systems
  PMP9492.3: PMP9492 is a conducted EMI optimized (CISPR 25 Class 5) 9 W Multi output Design for Wide Range Vin automotive ADAS application that supports Cold –Cranking Conditions . The design uses an LM53603 regulator IC (used as Buck), LM26420 (used as dual Buck) and TPS60150 regulator IC (used as Charge pump for 5V output). The design accepts an input voltage of 4.5Vin to 20Vin and provides the outputs of 3.3V @ 1.0A, 2.5V @ 1.0A, 1.8V @ 1.0A, and 5V @ 100mA. It features a small size and is an inexpensive and more efficient solution customized for ADAS and other Automotive related applications. The Board dimension of PMP9492 PCB is 2600mil × 4000mil. Four layer PCB was used for the design.
• Universal AC Input, Dual 12V, -8.5V Output Quasi-Resonant Flyback Converter Reference Design
  PMP10150.1: The PMP10150 reference design uses the UCC28600 quasi-resonant flyback controller to generate a 12V and a -8.5V output from an universal AC input. An optocoupler is used to regulate the 12V output.
• Xilinx Zynq 7000 Series (XC7Z045) 20W Reference Design - PMP10613.1 - TI Tool Folder
  PMP10613: The PMP10613 reference design provides all the power supply rails necessary to power Xilinx® Zynq® 7000 series (XC7Z045) FPGA. This design uses several LMZ3 series modules, LDOs, and a DDR termination regulator to provide all the necessary rails to power the FPGA. It also features one LM3880 for power up and power down sequencing. This design uses a 12V input.
• Power Solution for 450W Automotive Audio Amplifier
  PMP7837: The PMP7837 is a 4-phase synchronous boost converter that can take a 6-17V input and put out 24V at 450W. It is used for powering up to eight 50W automotive trunk amplifiers. The 4-phase synchronous design with 450kHz switching frequency per phase results in a compact and efficient circuit well suited for such applications.
• 230V AC input to 23V,0.42A Flyback LED Driver
  PMP7752: It is a TRAIC dimmable offline flyback LED driver using LM3445. It has an adaptive constant off-time AC/DC constant current controller feature. It can be used with input supply of 230V AC and can light 7 LEDs in string supplying 420mA of current.
• TPS92310 - 220VAC, 22W Non-isolated LED Driver with PFC for T8 Tube Application
  PMP8002: The main purpose of this reference design is to demonstrate a high performance and low component count offline LED driver with PFC based on TPS92310. This LED driver is designed for converting an AC input to a regulated LED current. The operating conditions and performance of the reference design are as follows:●198VAC to 264VAC, 50Hz Input Voltage ●65V to 75V LED Voltage ●280mA Regulated LED Current ●88% Typical System Efficiency ●High Power Factor>0.9 ●Output Short-Circuit and Open-Circuit Protection.
• 5V/10W Off-Line DCM Flyback Converter Optimized for Zero-Power at No-Load - Reference Design
  PMP9561: This design features the UCC28730 flyback controller in conjunction with the UCC24650 wake-up monitor to provide CV, CC regulated output with ultra-low stand-by power that exceeds Level VI and CoC Tier 2 specifications for average efficiency and 10% load efficiency. Wake-up signal detection provides fast transient response to large load steps.
• Multi-Cell Battery Manager Unit with Integrated Charging, Gauging, Authentication and Protection
  TIDA-00553: The Texas Instruments bq40z60 device is a Battery Pack Manager that integrates battery charging control output, gas gauging, and protection for completely autonomous operation of 2-series to 4-series cell Li-Ion and Li-Polymer battery packs. The architecture enables internal communication between the fuel gauging processor and battery charger controller to optimize the charging profile based on the external load conditions and power path source management during load transients and adaptor current limitations in the system. The charging current efficiency is scalable for power transfer based on the external components, such as the NFETs, inductor, and sensing resistor.
• 40W SEPIC Conv w/Dual-Inductor High Efficiency Operating w/Automotive Input Range Reference Design
  PMP9184C: This dual-inductor 13.2V@3A SEPIC converter achieves greater than 92% efficiency. It utilizes all surface mount components, maintains a low temperature rise and is capable of high peak load transients.
• 4.5Vin to 5.5Vin; 4Vout @ 0.7A; Flyback - PMP7964 - TI Tool Folder
  PMP7964?SYS-null-null-findchips-refdes-rd-null-wwe: A Flyback design accepting an input voltage of 4.5Vin to 5.5Vin and providing an isolated output of 4Vout that can deliver 0.7A.
• 15W Automotive Start Stop Power Supply - PMP9476 - TI Tool Folder
  PMP9476?SYS-null-null-findchips-refdes-rd-null-wwe: PMP9476 is non-sync buck converter plus a non-sync boost controller accepts an input voltage of 3.5V to 40V, and outputs 5V, capable of providing 3A of current to the load.
• CISPR 25 Class 5 Multi-Output Power Supply Reference Design for Rear Camera, Automotive ADAS Systems - PMP9492.3 - TI Tool Folder
  PMP9492: PMP9492 is a conducted EMI optimized (CISPR 25 Class 5) 9 W Multi output Design for Wide Range Vin automotive ADAS application that supports Cold –Cranking Conditions . The design uses an LM53603 regulator IC (used as Buck), LM26420 (used as dual Buck) and TPS60150 regulator IC (used as Charge pump for 5V output). The design accepts an input voltage of 4.5Vin to 20Vin and provides the outputs of 3.3V @ 1.0A, 2.5V @ 1.0A, 1.8V @ 1.0A, and 5V @ 100mA. It features a small size and is an inexpensive and more efficient solution customized for ADAS and other Automotive related applications. The Board dimension of PMP9492 PCB is 2600mil × 4000mil. Four layer PCB was used for the design.
• 65W High-efficiency CoC-5 tier2/DOE Level VI AC Adapter - TIDA-00519 - TI Tool Folder
  TIDA-00519?SYS-null-null-findchips-refdes-rd-null-wwe: This is a high efficiency 65W AC/DC design for a Universal input (85Vac to 265Vac) to 19.5V @3.33A output exceeding CoC-5 Tier2 and DOE Level VI requirements for external power supplies using the LM5023 Quasi-Resontant Flyback Controller with UCC24630 Synchronous Rectification Controller and CSD19531Q5A MOSFET. Additionally the LM8364 reset controller is used to provide input line AC UVLO protection. As seen at APEC
• Automotive Dual-buck with Pre-boost 3.3V @ 2.3A and 3.3V @ 1.8A Reference Design
  PMP8637.3: This design is an automotive power solution with two synchronous bucks and a pre-boost to keep the output voltage stable during cranking. The bucks provide 3.3V @ 2.3A and 3.3V @ 1.8A, the output of the pre-boost is 7.0V @ 2.1A.
• 8V-40V Input 5V/10A Synchronous Buck for Automotive Applications
  PMP7872: PMP7872 is a synchronous buck converter capable of 50W output power. This design uses the LM25117QPSQ emulated current-mode synchronous buck controller and AUIRLR2905Z MOSFETs for automotive applications.
• 9 to 42Vin 5V/9V/12V @ 3A Synchronous 4-Switch Buck-Boost Converter Reference Design
  PMP10624.2: PMP10624 is a synchronous 4-switch buck-boost converter which utilizes the LM5175 controller for USB type C applications. The output voltage can be selected for 5V, 9V or 12V at 3A using jumpers or open drain control switches. The LM5175 average current loop sets a maximum output current of 4A.
• PoE PSE Type 2 (30W) IEEE 802.3at Fully Autonomous Quad Port Solution. - TIDA-00290 - TI Tool Folder
  TIDA-00290?SYS-null-null-findchips-refdes-rd-null-wwe: A fully autonomous IEEE802.3at, Type 2 (30W) Power-over-Ethernet (PoE) 4 Port Power Sourcing Equipment (PSE) solution. An additional configuration of two non-standard, high power ports (<60W) is provided. Both configurations support Gigabit Ethernet data pass through in 1000BASE-T ports. This reference design is made up of two boards: Motherboard (TPS23861EVM-612) and Daughter board (TPS23861EVM-613). The daughter board features two TPS23861 IEEE 802.3at PoE PSE controller devices. The motherboard provides a multi-port base platform interface for the daughter board. Additionally, the motherboard provides interfaces for two optional boards: MSP-EXP430G2 LaunchPad™ (if custom Power Management programmability is desired) and USB-TO-GPIO Interface Adapter (if PC GUI based Power Management configuration is desired). The complete solution has undergone exhaustive PoE testing and passes all industry-recognized conformance/interoperability test suites allowing customers to copy/paste the design without concern. The 2-layer PCB, daughter card, design delivers all of this on a low cost platform.
• Small Form Factor 12W Ultra Wide Range Power Supply for Protection Relays - Reference Design - TIDA-00227 - TI Tool Folder
  TIDA-00227?SYS-null-null-findchips-refdes-rd-null-wwe: This small form factor, 12W power supply solution for protection relays handles an ultra-wide range of both AC and DC inputs making it a suitable platform to power a variety of lower power protection relays that need to be placed in a small housing. The power supply is designed to output industry standard voltages required in protection relays while also providing excellent line and load regulation. This solution has been engineered for high wattage with good efficiency and has also been pre-compliance tested for IEC61000-4 (EFT and Surge) and CISPR 11 Class A (Interference).
• 60Vin 12Vout @ 4A Buck Reference Design - PMP9333 - TI Tool Folder
  PMP9333?SYS-null-null-findchips-refdes-rd-null-wwe: The circuit has an operating input voltage range of 50V to 60V max. The output is set at 12V at 4A continuous, with a 7A peak transient.
• Universal AC Input 5V/10A/50W PSR Flyback Power Supply With Over 89% Avg Efficiency Reference Design
  PMP10974: PMP10974 is a quasi-resonant Flyback power suppy based on the UCC28730 primary side regulation (PSR) controller. The elimination of optocoupler using PSR topology promises higher reliability and lower system cost. The design achieves less than 40mW standby power losses and over 89% average efficiency. The design also features UCC2463x synchronous rectification controller.
• Hercules Safety MCU Industrial Power Solution Reference Design - PMP10189.2 - TI Tool Folder
  PMP10189: This reference design is a complete power solution for the Hercules™ Safety MCU. The input voltage can be in the range of 48..60V and it provides five different output rails with 12.0V @ 30mA, 5.0V @ 240mA, 3.3V @ 620mA, 3.3V @ 230mA and 1.2V @ 700mA.
• Xilinx Virtex UltraScale FPGA Power Solution with PMBus Reference Design
  PMP9475: The PMP9475 12V-input reference design provides all the power supply rails necessary to power Xilinx's Virtex® UltraScale™ family of FPGAs in a compact, highly efficient design. This design uses several of TI's PMBus Point-Of-Load voltage regulators for ease of design/configuration and telemetry of critical rails. It features a UCD90120A for flexible power up and power down sequencing as well as voltage monitoring, current monitoring, and voltage margining through the PMBus interface.
• High Efficiency Synchronous Flyback with 36-72Vin to 5Vout@2A Reference Design
  PMP8917: PMP8917 has been designed as a competitive open-frame alternative for the communications market with 36-72Vin to 5V/2A. The product is supplied in the industry standard footprint of 2.0 x 1.0 x 0.394 inches. PMP8917 has a basic insulation system from input to output making it suitable for a wide variety of applications. LM5020 is used as synchronous Flyback converter controller for PMP8917 with 92.9% converter efficiency.
• DAC Sample and Hold Glitch Reduction Reference Design - TIPD142 - TI Tool Folder
  TIPD142?SYS-null-null-findchips-refdes-rd-null-wwe: DAC R-2R architectures display great performance in regards to noise and accuracy, but at a cost of large glitch area. This design focuses on the reduction of major-carry glitches that occur from code specific transitions in DAC R-2R architectures. This design reduces this glitch area, making it suitable for glitch-sensitive applications such as waveform generation.
• Compact Size Dual 2.5A USB Car Charger Reference Design
  PMP9402: PMP9402 is a dual USB car charger. This design utilizes the LM3150, TPS2561 Dual Channel Power Switch and a TPS2513 USB Dedicated Charging Port Controller. This design operates from 6 to 40V in. The output is set to 5V; both channels have a 2.5A current limit. This design has a switching frequency of 300 kHz. This design is intended for after-market automotive applications.
• Primary Side Regulated Flyback Reference Design with 120VAC Input and 24V/4A Rated Output - PMP10804 - TI Tool Folder
  PMP10804?SYS-null-null-findchips-refdes-rd-null-wwe: This reference design implements the UCC28630 PSR controller in a flyback power supply. The UCC28630 is capable of operating in both Continuous and Discontinuous Conduction Modes which enables high efficiency while reducing inductor size and cost. Safety standards such as EN60950 require that any X-capacitors in EMC filters on the AC side of the bridge rectifier quickly discharge to a safe level when AC is disconnected. Typically, this requirement is achieved by including a resistive discharge element in parallel with the X-capacitor. However, this resistance causes a continuous power dissipation that impacts the standby power performance. In order to reduce standby power and eliminate the standing loss associated with the conventional discharge resistors, the UCC28630 device incorporates active X-capacitor discharge circuitry. In this design, less than 100mW no load power comsumption and over 88% converter efficiency is achieved.
• Automotive Low Voltage SEPIC Stage Converts 4V…40Vin to 12Vout@2.5A Reference Design - PMP10111 - TI Tool Folder
  PMP10111?SYS-null-null-findchips-refdes-rd-null-wwe: This small SEPIC converter accepts a wide input voltage range, 4V...40V, from automotive battery and supports the cranking phase. Vout is kept stable thank to the SEPIC topology. During cranking the input voltage can reach vaules as low as 4V. Extensive testing with a source generator have been performed.
• Three Output, 7W, Isolated Fly-back Reference Design - PMP10866.1 - TI Tool Folder
  PMP10866: This compact design is intended for use as a 14V bias. It can connect to the secondary side of an LLC and acts as a bias for 2 separate PFCs.