Part Details for CSD18504Q5A by Texas%20Instruments

PMP9750 is a CLL resonant converter reference design with 400VDC input and 28V/9A ouput. Unlike LLC series resonant converter, CLL resonant converter used in PMP9750 utilizes its output inductor to minimize the size of the resonant tank. With resonant controller UCC25600 and bridge driver UCC2771

BQ24745 is a host controlled synchronous buck battery charger capable of charging batteries at up to 19.2V and up to 8 A normally: extended to 10 A with use of 8 mOhm battery sense resistor. The power train is capable of 8 A with convection only cooling and 10 A with moderate fan cooling (~200 LFM). The Test Report includes Thermal images for both cases. While the design shows a 28 pin MSP430 as the host: any processor with SMBus capability will work. A 5/12V 2A auxiliary converter using TPS54335: and 5V 4A with TPS40170 with 2x CSD18504 are provided. For the two USB ports: the design provides TPS2561A for power switching and TPS2513A for control. A linear TPS70933 provides the 3.3V for the MSP430 and interface signals. A rich Test Interface allows full testing of hardware in the absence of software and then provides multiple interface choices for software development.

This reference design operates from a 6V to 16V input and supplies 12V @ 5A out. It utilizes the LM5122 synchronous boost controller to operate as a synchronous SEPIC converter.  The circuit achieves greater than 95% efficiency at maximum load.

16-Cell EV/HEV High Current Active Balance Solution: using the latest automotive battery management monitor and protector: the bq76PL455A-Q1. It provides high-performance battery management solution for large capacity battery packs: by combining the high integration and accuracy of the bq76PL455A-Q1 with a bi-directional DC-DC cell balancer. This allows any of 16 cell inputs to be charged or discharged as needed at up to 5A: and modules can be stacked up to 1300V.

在笔记本电脑应用中，PMP5885 给 CPU 和 GFX 供电。CPU 由 TPS59610 控制器和两个 NexFET 供电，以满足 18A 电气/10A 热要求。TPS51220A 和 NexFET 为 GFX 提供 1.05V (15A)，同时满足 5V (5A) 的要求。

A system example for an active cell balancing battery management system. The TMS570LS0432 microcontroller commands EMB1402 EVM to monitor the battery cells and perform charge/discharge from one battery cell to an external 12V supply. The user can view the cell status and control cell balancing from a GUI running on the host PC.

采用 3D 飞行时间 (ToF) 的需求控制通风人数统计参考设计是一种子系统解决方案，它使用 TI 的 3D ToF 影像传感器以及跟踪和检测算法对给定区域中的人进行计数，可实现高分辨率和高精度。该传感器技术是在标准 CMOS 中开发的，使系统能够以较低的系统成本实现很高的集成度。由于 ToF 影像传感器以三维处理可视化数据，因此传感器可以检测到人体的精确形状并以前所未有的精度跟踪人的移动和位置（包括微小的移动变化）。因此，ToF 摄像头能够比传统监控摄像头和视频分析更加高效地执行实时人数统计和人员跟踪功能。

PMP5783 是一个完整的 Intel IMVP6.5 Arrandale SV/Clarksfield SV 电源参考设计。输入电压为 8-15V。主 CPU 由两相 TPS59621 供电。TPS59611 给图形处理器供电。DDR3 内存由 TPS5126 供电。两个 1.05V 电压均由 TPS51218 提供。双路 TPS51125A 提供 5V 和 3.3V 电压。上述动力总成均使用双路 NexFET CSD86350。TPS62290 提供 1.8VS。

The Texas Instruments TPS6110x evaluation modules (EVM) for high-efficiency boost converters help designers to evaluate the different operating modes and the performance of the device. If any other output voltage configuration is to be evaluated, the TPS61100 adjustable output voltage version can be set up to provide an output voltage between 1.5 V and 5.5 V at the output of the boost converter and between 0.9 V and 3.3 V at the LDO. Only the appropriate feedback resistor divider has to be adjusted. Also, other fixed output voltage versions of the devices can be easily evaluated using the EVM. The TPS6110x has an input voltage range between 0.9 V and 3.6 V. For proper operation the maximum input voltage should not exceed the output voltage. The maximum output current is at least 100 mA depending on the input voltage.

This design implements an isolated data converter that utilizes residual power from the interface to power itself. This removes the requirement for expensive power transmission across the isolation boundary. By easily enabling the ubiquitous RS-232 connection on an electric meter, features like f

The PMP20981 reference design utilizes the TPS2384 PSE Power Manager to implement a single port Type 1 PoE PSE.  An isolated flyback converter: utilizing the LM3481 current mode PWM controller: accepts a 12Vdc input and provides a 48Vdc/360mA output source for the PSE.  This design is ideally suited for any Type 1 (15W) PoE PSE application.

Simple, low power, dual output supply w/ TPS54060 to supply low power DSPs, ASICs or similar outputs from wide input voltage range.

TIDA-00741 uses two TPS2378 PD controllers for a forced 4-pair UPOE solution to 51W non-standard PoE PD applications. It incorportates the UCC2897A controller in a high-efficiency: great transient response (driven) synch flyback converter capble of 12V at 3.8A.

TIDA-00539 uses two TPS2378 PD controllers for a forced 4-pair UPOE solution to 51W non-standard PoE PD applications. It incorportates the UCC2897A controller in a high-efficiency: great transient response (driven) synch flyback converter capble of 19V at 2.3A.

此设计是 bq20z65/bq29412 电池管理系统的完整解决方案。此设计包含一个 bq20z65/bq29412 电路模块和与基于 Windows™ 的 PC 软件的链接。此电路模块设计包含一个 bq20z65 集成电路 (IC)、一个 bq29412 IC，还包含监控和预测容量、执行电池平衡、监控关键参数、防止 2、3 或 4 节锂离子或锂聚合物电池组中出现过充、过放电、短路和过电流所需的所有其它板载组件。此参考设计直接与电池组中的电池相连。借助 EV2300 接口板和软件，用户可以读取 bq20z65 数据寄存器、对适用于不同数据包配置的芯片组进行编程、记录循环数据以便进一步评估，并对 bq20z65/bq29412 解决方案在不同充电和放电条件下的整体功能进行评估。

The PMP21098 reference design uses UCC28056 transition mode PFC controller and UCC25630 enhanced LLC controller with integrated driver to provide 12V/10.8A output (continuous: 14.2A peak) from universal AC input. This design achieves 91.8% peak efficiency at 115VAC input and 93.4% peak efficiency at 230VAC input. The efficiency and power factor numbers also meet both 115V and 230V internal 80 PLUS gold specifications. In addition: the design is able to achieve less than 300mW power consumption at no load without turning off PFC.

PMP7756 是有源钳位正向控制器。其具有 6V、18A 隔离输出。其采用自驱动同步调节。

This reference design showcases various power architectures for generating multiple voltage rails for an application processor module: requiring >1A load current and high efficiency . The required power supply is generated using 5-: 12- or 24-V DC input from the backplane. Power supplies are generated using DC-DC converters with an integrated FET and a power module with an integrated inductor for size. The design features a HotRod™ package type for applications requiring low EMI. It is also optimal for design time constrained applications. Additional features include DDR termination regulator: input supply OR-ing: voltage sequencing: eFuse for overload protection: and voltage and load current monitoring. This design can be used with a  processor: digital signal processor and field-programmable gate array. It has been tested for radiated emission: per CISPR22 meeting class A and B requirements.

PMP11474 参考设计测量 USB type C 电缆中存在的电压和电流。通过 INA213 电流放大器在 5mΩ 的感应电阻器上监测电流。通过 LM321 放大器监测电压。通过 MSP430 处理这些测量值并在小型 LCD 屏幕上进行显示。

The 36-60Vdc input range of the PMP11420 reference design is well suited for telecom: POE or any 48Vdc input application.  The synchronous rectifier provides excellent efficiency over the full input range.  The LM5020 PWM controller operates with peak current mode control and features input UVLO and an integrated start-up regulator.

This reference design implements an IEEE802.3bt (draft) Power over Ethernet (PoE) Powered Device (PD) with dual redundant inputs and a smooth transition between these inputs and an auxiliary input.  The design consists of a 5V/6A synchronous flyback converter and allows for up to three power supplies (two PoE Power Source Equipment (PSE) supplies and one AC/DC wall adapter auxiliary supply) to be used in order to decrease the probability of power and data loss in your system.In need of an IEEE802.3bt-ready PSE controller? Check out the TPS23881.

此参考设计展示了适用于电池供电型智能流量计电池和系统运行状况监控的创新解决方案。此电池监控子系统可实现高精度电能计量和运行状况 (SOH) 计划，可预测电池寿命。此系统监控子系统针对可能会大幅缩短电池寿命的过流状态提供保护。本文中说明的技术可帮助延长电池供电计量表的有效寿命，并优化使用者的总拥有成本。

TIDA-01052 参考设计旨在突显在模拟前端驱动器放大器上使用负电压轨而不是接地所致的系统性能提升。此概念与所有模拟前端有关，但此设计专门针对自动测试设备。

PMP40133 控制板为接口提供了快速充电器适配器解决方案。主 MCU 是 MSP430G2955，它使用 MaxCharge™ 技术控制与充电器器件的通信。使用 TPL0102-100 数字电位器来微调适配器输出电压。256 个抽头可实现 10mV 电压设置调整精度。对适配器的 OCP 和 OVP 使用 INA199B 电流检测电路和分压器电路。

该汽车预升压参考设计的标称输入电压范围为 2.7V 至 10.5V，可在启动时提供 10.5V 电压 (3.0A)。它可以承受最高 32.0V 的峰值电压。该升压控制器可在 400KHz 下工作，并可实现 93% 的峰值效率。

TIDA-00701 is a 100W: 24V: Industrial AC-DC power supply designed for use in Industrial & Instrumentation systems such as process controls: factory automation and machinery control. This reference design has front end Power Factor Correction (PFC) circuit designed using UCC28051 PFC controller: followed by Quasi-Resonant flyback converter implemented using UCC28740 Primary Side regulated (PSR) CC-CV flyback controller: with all the necessary protections built-in. Hardware is designed and tested to pass conducted emissions: surge: and EFT requirements.The key highlights of this reference design are:Reduced component count design to achieve NEC Class-2 and Limited Power Source (LPS) normsMeets Energy Star Rating and 2013 EU eco-design directive Energy-related Products (ErP) Lot 6Meets stringent current THD normsRobust output supply protected for output over-current: output short circuit: output over-voltage: and over temperature conditions

PMP10712 is a 1.2W: small form factor: isolated flyback design that supports very low Vin of 3.3V-6V and is capable of delivering 10mA at 120V output. The design uses LM3481 Boost controller IC which works on current mode operation and can be synchronized to any frequency between 100KHz to 1 MHz.This design was built on a 2 layer board and is a simple: low-BOM-count: and low-cost design providing an isolated output.

The wide 9-36Vdc input range of this design is well suited for applications operating from 12V/24V dc inputs.  The synchronous rectifier provides excellent efficiency over the full input range.

The following design is a 60W Flyback which uses the UCC3809 and the UCC39002. It creates a 12V@10A output by employing dual 12V@5A. The system functions in the continuous conduction mode.

This design is a primary side regulated flyback (optocoupler-less) with secondary side synchronous rectification and an input voltage range of 85VAC to 240VAC. It delivers an output of 5.0V@1.6A.

This synchronous buck regulator provides 96% efficiency when regulating 24Vin to 15V out @ 5A. The output can be set to regulate 12V : if desired. PMP8493 uses TPS40170 wide input synchronous buck controller.

This synchronous buck converter operates over a 19-V to 32-V input range and delivers 12 V at 8-A continuous. It achieves an efficiency of greater than 97% between 4.5 A to 8 A at 24 Vin. Other features include low-output ripple voltage: excellent transient response: and small size.

The PMP10352 reference design is a flyback converter with a 10-14Vdc input and 48V/360mA output.  This design is well suited to provide power for Type 1 (15W) Power over Ethernet (PoE) Power Source Equipment (PSE) switches.  It can also be used for any application operating from a 12V bus that needs an isolated 48V output.