FindChips.com

Reference Designs

• Low-Power Reference and Bipolar Voltage Conditioning Circuit Reference Design for Low-Power ADCs - TIPD154 - TI Tool Folder
  TIPD154?SYS-null-null-findchips-refdes-rd-null-wwe: This TI Precision Verified Design provides the theory, component selection, and simulation for a single-supply, low-power signal conditioning circuit designed to translate a +/-5 V input signal to the proper input range of a single-supply low-power 16-Bit ΔΣ ADC such as the one inside the MSP430 or other similar single-supply ADCs. A zero-drift op amp was selected to provide excellent dc performance in the attenuation and level-shifting circuit. Two low-power reference circuits are used to provide power, the ADC reference voltage, and biasing to the input conditioning circuit.
• 2.2MHz Switching, Synchronous Split Supply Reference Design for 12V Battery with all Protections
  PMP10651.4: PMP10651 is a low noise, multi-output SMPS design where LM53603 is used in Inverting Buck-Boost Fly buck topology to generate positive and negative supply needed in multiple noise sensitive applications such as powering High Speed Video Amplifier, RF amplifier, Precision Low noise amplifier etc. The design accepts an input voltage of 7Vin to 15 Vin DC (from 12V Lead Acid Battery) and provides outputs of +12V@500mA, -12v@500mA, 5V @400mA and 3.3V@150mA. It features a small size and is an inexpensive and more efficient solution to using Flyback or Pushpull converters .
• 2.2MHz Switching, Synchronous Split Supply Reference Design for 12V Battery with all Protections
  PMP10651.1: PMP10651 is a low noise, multi-output SMPS design where LM53603 is used in Inverting Buck-Boost Fly buck topology to generate positive and negative supply needed in multiple noise sensitive applications such as powering High Speed Video Amplifier, RF amplifier, Precision Low noise amplifier etc. The design accepts an input voltage of 7Vin to 15 Vin DC (from 12V Lead Acid Battery) and provides outputs of +12V@500mA, -12v@500mA, 5V @400mA and 3.3V@150mA. It features a small size and is an inexpensive and more efficient solution to using Flyback or Pushpull converters .
• Offline AC/DC 75W Quasi-Resonant Flyback Converter Reference Design
  PMP10100: The PMP10100 reference design uses the LM5023 flyback controller for the Quasi-Resonant Flyback Topology. It generates an isolated output (19.5V@3.84A) from an universal input (85VAC - 265VAC).
• Triac Dimmable AC-DC LED Driver Reference Design - PMP6013 - TI Tool Folder
  PMP6013?SYS-null-null-findchips-refdes-rd-null-wwe: This reference design provides a high-brightness LED driver based on the TPS92310 configured as a power factor corrected flyback regulator that is triac dimmable. It is designed to operate with an input voltage in the range of 90VAC to 135VAC with a 120VAC nominal input voltage. This design is set up for a default output current of 340mA with an output voltage range of 21V to 27V or approximately 6 to 8 LEDs depending on the forward voltage of each.
• Automotive Buck-boost Converter Providing 8V @ 1.5A Reference Design
  PMP8635: This design is a buck-boost converter for automotive applications covering an input voltage range of 2..20V. It provides an output voltage of 8.0V @ 1.5A continuous / 2.5A peak.
• Universal supply source - 12VAC / 12VDC to 300mA SEPIC converter for MR16 / AR111 (3&4 LEDs / 10V ~1 - PMP8021 - TI Tool Folder
  PMP8021?SYS-null-null-findchips-refdes-rd-null-wwe: The main purpose of this reference design is to demonstrate a very good compatibility of Power source SEPIC topology LED driver based on TPS92560. This LED driver is designed for converting a power source DC, AC & E-transformer to a regulated LED current. The operating conditions and performance of the reference design are as follows: 12VDC, or 12Vac / 50Hz 60Hz, or 12VAC E-transformer, Output Power 3 ~ 4W, 10 ~13V LED voltage , 300mA Regulated LED Current , 75% Typical System Efficiency, High Power Factor > 0.9, Output Short-Circuit and output Open-Circuit Protection.
• Automotive Camera Module Reference Design for Uncompressed Digital Video With Wide Vin Front End
  PMP10653.3: PMP10653.3 is an Optimized Automotive Camera Module Design for Uncompressed Digital Video over Coax cable. The design is broadly divided into four Blocks.
• 2.2MHz Switching, Synchronous Split Supply Reference Design for 12V Battery with all Protections
  PMP10651.3: PMP10651 is a low noise, multi-output SMPS design where LM53603 is used in Inverting Buck-Boost Fly buck topology to generate positive and negative supply needed in multiple noise sensitive applications such as powering High Speed Video Amplifier, RF amplifier, Precision Low noise amplifier etc. The design accepts an input voltage of 7Vin to 15 Vin DC (from 12V Lead Acid Battery) and provides outputs of +12V@500mA, -12v@500mA, 5V @400mA and 3.3V@150mA. It features a small size and is an inexpensive and more efficient solution to using Flyback or Pushpull converters .
• Isolated Auto-Polarity RS-485 Transceiver Reference Design
  TIDA-00263: This reference design demonstrates an isolated RS-485 bus node with automatic correction of a reversed bus signal polarity caused by cross-wire faults. The design provides transient protection protecting the signal path against ESD, EFT, and surge transients specified in the IEC 61000 family of transient immunity standards. An isolated DC-DC converter provides power supply across the isolation barrier utilizing the push-pull converter principle.
• Dual-Stage Triple-Output Buck Converter
  PMP7800.2: The PMP7800.2 reference design is a Buck which uses a LMR14203 and was intended for Computers and Peripherals applications. It can generate a Non-Isolated 1.8 volt output at 0.23 Amps from an input 21.6 to 26.4 Volts DC.
• Non-Isolated Synchronous Buck used for Transportation and Automotive Applications
  PMP7858: This is a synchronous buck converter with an input voltage range of 8V-to-16Vin (40Vin max) and a regulated output at 5Vout @ 1.5A.
• Automotive Camera Module Reference Design for Uncompressed Digital Video With Wide Vin Front End
  PMP10653.1: PMP10653.1 is an Optimized Automotive Camera Module Design for Uncompressed Digital Video over Coax cable. The design is broadly divided into four Blocks.
• 2.2MHz Switching, Synchronous Split Supply Reference Design for 12V Battery with all Protections
  PMP10651.2: PMP10651 is a low noise, multi-output SMPS design where LM53603 is used in Inverting Buck-Boost Fly buck topology to generate positive and negative supply needed in multiple noise sensitive applications such as powering High Speed Video Amplifier, RF amplifier, Precision Low noise amplifier etc. The design accepts an input voltage of 7Vin to 15 Vin DC (from 12V Lead Acid Battery) and provides outputs of +12V@500mA, -12v@500mA, 5V @400mA and 3.3V@150mA. It features a small size and is an inexpensive and more efficient solution to using Flyback or Pushpull converters .
• Dual Boost with +15V@300mA and -15V@300mA Output Reference Design
  PMP10091.2: This reference design provides positive and negative output of 15V.
• Space Optimized Wide Vin Triple-Output Power Module Reference Design
  TIDA-00783.1: The TIDA-00783.1 reference design is a triple output wide Vin power module design. It provides 3.3V, 1.8V and 1.2V output, at 6W total power. The layout is optimized for space constrained applications.
• High Definition (HD) Automotive SerDes w/ 24 Bit RGB Interface over twisted pair for TFT LCD Display
  TIDA-00132: The TIDA-00132 reference design is a high speed serial video interface to connect a remote automotive TFT LCD display with 720px60 format and 24Bit parallel RGB Interface to a video processing system. It uses TIs FPD-Link III SerDes technology to transmit uncompressed video data (with Content Protection - HDCP option) and bidirectional control signals over shielded twisted pair. This design incorporates the DS90UB925QSEVB and DS90UB926QSEVB boards together to create the solution
• 60Vin 12Vout @ 4A Buck Reference Design
  PMP9333: The circuit has an operating input voltage range of 50V to 60V max. The output is set at 12V at 4A continuous, with a 7A peak transient.
• Dual Output Rail Power Supply with Inverting Buck Boost Converter Reference Design
  PMP10090.1: PMP10090.1 shows a power supply, which provides a positive and a negative voltage rail in an inverting Buck Boost configuration. A 12V input is converted to 15V and -15V output voltages with 700mA load current each.
• Multi-output Multi-buck 20W Power Supply for Xilinx Zynq FPGA Applications Reference Design
  PMP9335: PMP9335 is designed for Xilinx Zynq FPGA applications utilizing the TPS84A20 and TPS84320. This design uses an external timer to synchronize the switching frequency to 300 kHz. It also employs a controlled power up and power down sequence.
• Analog Input Module for Industrial Outputs and Temperature Sensors Reference Design - TIPD164 - TI Tool Folder
  TIPD164?SYS-null-null-findchips-refdes-rd-null-wwe: This TI Designs, Precision Verified design implements an analog input module for industrial voltages, currents, and temperature sensors. For industrial outputs, the possible input ranges include: 4-20 mA, 0-20 mA, +/-25 mA, 0-5 V, 0-10 V, +/-5 V, +/-10 V. The design includes conditioning and level-shift circuitry which converts the large industrial outputs into a proper input range for a +5V delta-sigma ADC. The ADC has features to directly acquire information from the RTD and thermocouple sensors over their full temperature range.
• Space Optimized Wide Vin Triple-Output Power Module Reference Design - TIDA-00783.3 - TI Tool Folder
  TIDA-00783: The TIDA-00783.3 reference design is a triple output wide Vin power module design. It provides 3.3V, 1.8V and 1.2V output, at 6W total power. The layout is optimized for space constrained applications.
• Offline AC/DC 75W 2-Switch Quasi-Resonant Flyback Converter Reference Design - PMP10035 - TI Tool Folder
  PMP10035?SYS-null-null-findchips-refdes-rd-null-wwe: This design uses the LM5023 flyback controller for the 2-Switch Quasi-Resonant Flyback Topology. It generates an isolated output (19.5V@3.84A) from an universal input (85VAC - 265VAC).
• Space Optimized Wide Vin Triple-Output Power Module Reference Design
  TIDA-00783.2: The TIDA-00783.2 reference design is a triple output wide Vin power module design. It provides 3.3V, 1.8V and 1.2V output, at 6W total power. The layout is optimized for space constrained applications.
• Dual-Stage Triple-Output Buck Converter
  PMP7800.3: The PMP7800.3 reference design is a Buck which uses a LMR14203 and was intended for Computers and Peripherals applications. It can generate a Non-Isolated 1.8 volt output at 0.23 Amps from an input 21.6 to 26.4 Volts DC.
• Dual Isolated Half-Duplex RS-485 Repeater Reference Design
  TIDA-00333: This reference design demonstrates a dual isolated, half-duplex repeater with data rate independent flow-control for long-haul RS-485 networks suitable for industrial applications. The design provides transient protection protecting the signal path against ESD, EFT, and surge transients specified in the IEC 61000 family of transient immunity standards.
• Single-Channel Industrial Voltage & Current Output Driver, Isolated, EMC/EMI Tested Reference Design
  TIPD153: This TI CerTIfied Reference Design implements a isolated single-channel industrial voltage and current output module using the DAC8760 and ISO7641. The circuit features a digitally controlled voltage or current output that produces the standard outputs of 0-20mA, 0-24mA, 4-20mA, 0-5V, +/-5V, 0-10V and +/-10V outputs based on the internal register settings of the DAC8760. The design includes the required external protection circuitry needed to pass the IEC61000-4-2/3/4/6 tests and IEC61000-4 test results are included. The protection circuitry does not negatively affect the voltage or current output performance resulting in <0.1% total unadjusted error (TUE) for both outputs.
• Automotive Acoustic Knock Sensor Interface
  TIDA-00152: This TIDA-00152 reference design utilizes a dual-channel, signal processing IC for detection of premature detonation in combustion (gasoline) engines. The heart of this design is the TPIC8101 that serves as an interface between acoustical sensors or accelerometers and automobile engine management systems. Programmable features on this device include the selection of engine knock detection sensitivity, engine resonance frequency, and sampling rate control of on-board ADC and DAC in signal processing chain. These features allow the TPIC8101 to be a flexible interface that can adapt to cost and/or processing time constraints of the customer.
• 100-240VAC Input, 60W, 2-string, PWM Dimmable LED Driver Reference Design - PMP6024 - TI Tool Folder
  PMP6024?SYS-null-null-findchips-refdes-rd-null-wwe: PMP6024 is an offline, LED driver circuit consisting of an isolated, power-factor corrected, constant output voltage flyback converter followed by two DC/DC buck LED current controllers. It is suitable for indoor or outdoor area lighting applications of 3500-5000 lumens (depending upon LED selection). LED brightness is controlled by a 3.3V, 10kHz PWM signal which is converted to a DC level adjustment of the LED string currents avoiding PWM modulation of the light output.
• AC-mains LED Lighting with DALI DMX512 & Power Line Communications Reference Design
  TIDM-AC-LED-COM: Ideal for outdoor, entertainment, and industrial lighting applications, this LED Lighting design provides high power and high efficiency illumination with built-in communications networking. The lighting unit consists of a 250W universal AC-input LED driver power supply and a demonstrational six-string LED lamp. Driving the LED’s with great power efficiency and electrical utilization, the LED driver power supply operates at greater than 90% power efficiency with 0.99 power factor (PF). Furthermore, to support system-networked lighting and remote connectivity, this power supply includes support for common lighting communications standards including Digital Addressable Lighting Interface (DALI), DMX512, and Power Line Communications (PLC).
• TPS92310 Universal 18W
  PMP8006: The main purpose of this reference design is to demonstrate a high efficiency offline LED driver with PFC based on TPS92310. This LED driver is designed for converting an AC input to a regulated LED current.The operating conditions and performance of the reference design are as follows: 1.90VAC to 264VAC, 60/50HZ Input voltage;2.55V to 65V LED Forward Voltage;3.275mA Regulated LED Current;4.System Efficiency ≥ 90%;5.High Power Factor > 0.9;6.Output Short-Circuit and Open-Circuit Protection.
• 6.5V/2A Boost Converter Reference Design
  PMP10026: This reference design provides an output voltage of 6.5V from an input voltage range of 3V to 6.5V.
• IEC ESD, EFT, and Surge Protected RS-485 Reference Design - TIDA-00731 - TI Tool Folder
  TIDA-00731?SYS-null-null-findchips-refdes-rd-null-wwe: The TIDA-00731 is a reference design examining how to protect an RS-485 bus against lethal transient waveforms such as IEC ESD, IEC EFT, and IEC surge. The reference design shows the level of protection that can be achieved through the implementation of an external protection scheme on the bus lines of a standard RS-485 transcever as well as a RS-485 tranceiver with integrated IEC protection.
• Dual-channel XAUI to SFI Reference Design for Systems with Two or More SFP+ Optical Ports
  TIDA-00234: The TIDA-00234 XAUI to SFI reference design is intended for Enterprise and Service Provider Networking applications like Ethernet Switches and Routers that implement multiple 10G Ethernet compliant Optical (SFP+) ports. This reference design features the TLK10232 device which is the most compact Dual-channel XAUI-to-SFI Transceiver with the lowest power consumption in its category. This reference design allows access to the high-speed signals (up to 10Gbps) generated by the TLK10232 via SMA connectors or an SFP+ Module via the SFP+ optical module cage. Also, featured is the CDCM6208 device that can provide extremely low-jitter Clock input to the TLK10232 in customer systems that do not have one available (or does not meet the jitter requirement of the system).
• ±12V/700mA Dual Power Supply Reference Design
  PMP10088.2: PMP10088 is a reference design which provides a dual output +12V and -12V from an industrial input voltage of 24V.
• DisplayPort Video 4:1 Aggregation Reference Design
  TIDA-00309: This verified reference design is a complete four channel DisplayPort aggregation and de-aggregation solution. One TLK10022 is used to aggregate four synchronous DisplayPort (DP) sources together into one 10.8 Gbps serial link. The serial data is transferred via copper or optical fiber where a second TLK10022 is used to de-aggregate and seamlessly redisplay the original video content.
• 30W Isolated Synchronous Flyback Converter Reference Design
  PMP10506: PMP10506 is an isolated synchronous flyback converter using the LM5122 controller IC. The design accepts an input voltage of 9Vin to 60Vin and provides an isolated output of 5Vout capable of supplying 6A of continuous current to the load.
• Single cell Li-Ion/Li Polymer Battery protection IC Reference Design - TIDA-00265 - TI Tool Folder
  TIDA-00265?SYS-null-null-findchips-refdes-rd-null-wwe: The bq297xy device provides the protection functions for Li-Ion/Li-Polymer cells, and monitors across the external power FETs for protection due to high charge or discharge currents. In addition, there is overcharge and depleted battery monitoring and protection. These features are implemented with low current consumption in NORMAL mode operation.
• LM3448 – 220VAC, 8W Dimmable Isolated
  PMP8001: This demonstration board highlights the performance of a LM3448 based Flyback LED driver solution that can be used to power a single LED string consisting of 6 / 7 series connected LEDs from an 198 VRMS to 264 VRMS, 50 Hz input power supply. The integrated high-voltage and low Rdson MOSFET reduces design complexity while improving LED driver efficiency. This is a two-layer board using the bottom and top layer for component placement. The demonstration board can be modified to adjust the LED forward current, the number of series connected LEDs that are driven and the switching frequency. Refer to the LM3448 datasheet for detailed instructions. A bill of materials is included that describes the parts used on this demonstration board
• Power Line Communications (PLC) Lite™ Reference Design for Industrial Applications - TIDM-INDUSTRIAL-PLC - TI Tool Folder
  TIDM-INDUSTRIAL-PLC?SYS-null-null-findchips-refdes-rd-null-wwe: This TI implementation of Power Line Communications (PLC) is a new option for adding communications to industrial equipment such as solar arrays. PLC Lite™ offers higher data throughput than earlier forms of PLC and greater robustness for transmission across noisy electric lines by using OFDM PHY technology. This design is based upon a C2000 controlCARD and an analog front end for PLC. The C2000 MCU executes the entire PLC Lite software stack. TIDM-INDUSTRIAL-PLC achieves up to 21 kbps data rates across AC or DC power lines compared to traditional SFSK PLC solutions (2-5 kbps) all while decreasing the overall BOM cost of a typical PLC modem.
• 30W Isolated Synchronous Flyback Converter Reference Design - PMP10506 - TI Tool Folder
  PMP10506?SYS-null-null-findchips-refdes-rd-null-wwe: PMP10506 is an isolated synchronous flyback converter using the LM5122 controller IC. The design accepts an input voltage of 9Vin to 60Vin and provides an isolated output of 5Vout capable of supplying 6A of continuous current to the load.
• Dual Boost with +15V@300mA and -15V@300mA Output Reference Design
  PMP10091.1: This reference design provides positive and negative output of 15V.
• 20W SEPIC Low-Cost Lead Acid Battery Charger Reference Design
  PMP10081: The PMP10081 reference design shows a simple and low-cost solution of a lead acid battery charger. The input voltage range is from 9V to 36V and the maximum output voltage is 13.8V, which is sufficient for a six-cell lead acid battery with a charge current up to 1.5A.
• Universal supply source - 12VAC / 12VDC to 300mA SEPIC converter for MR16 / AR111 (3&4 LEDs / 10V ~1
  PMP8021: The main purpose of this reference design is to demonstrate a very good compatibility of Power source SEPIC topology LED driver based on TPS92560. This LED driver is designed for converting a power source DC, AC & E-transformer to a regulated LED current. The operating conditions and performance of the reference design are as follows: 12VDC, or 12Vac / 50Hz 60Hz, or 12VAC E-transformer, Output Power 3 ~ 4W, 10 ~13V LED voltage , 300mA Regulated LED Current , 75% Typical System Efficiency, High Power Factor > 0.9, Output Short-Circuit and output Open-Circuit Protection.
• High Definition (HD) Automotive SerDes w/ 24 Bit RGB Interface over twisted pair for TFT LCD Display - TIDA-00132 - TI Tool Folder
  TIDA-00132?SYS-null-null-findchips-refdes-rd-null-wwe: The TIDA-00132 reference design is a high speed serial video interface to connect a remote automotive TFT LCD display with 720px60 format and 24Bit parallel RGB Interface to a video processing system. It uses TIs FPD-Link III SerDes technology to transmit uncompressed video data (with Content Protection - HDCP option) and bidirectional control signals over shielded twisted pair. This design incorporates the DS90UB925QSEVB and DS90UB926QSEVB boards together to create the solution
• Multi-output Multi-buck 20W Power Supply for Xilinx Zynq FPGA Applications Reference Design - PMP9335 - TI Tool Folder
  PMP9335?SYS-null-null-findchips-refdes-rd-null-wwe: PMP9335 is designed for Xilinx Zynq FPGA applications utilizing the TPS84A20 and TPS84320. This design uses an external timer to synchronize the switching frequency to 300 kHz. It also employs a controlled power up and power down sequence.
• Dual-Stage Triple-Output Buck Converter
  PMP7800.1: The PMP7800.1 reference design is a Buck which uses a LMR14203 and was intended for Computers and Peripherals applications. It can generate a Non-Isolated 3.3 volt output at 0.07 Amps from an input 21.6 to 26.4 Volts DC.
• Offline AC/DC 75W 2-Switch Quasi-Resonant Flyback Converter Reference Design
  PMP10035: This design uses the LM5023 flyback controller for the 2-Switch Quasi-Resonant Flyback Topology. It generates an isolated output (19.5V@3.84A) from an universal input (85VAC - 265VAC).
• Interface to a Sin/Cos Encoder with Sitara AM437x Reference Design
  TIDA-00178: The TIDA-00178 reference design is an EMC compliant industrial interface to Sin/Cos position encoders. Applications include industrial drives, which require accurate speed and position control. The design utilizes a 16-bit dual sample ADC with drop-in compatible 14- or 12-bit versions available, allowing for optimization of performance and cost. TIDA-00178 provides a direct connection to Sitara AM437x using SPI and QEP. For quick evaluation it features a 60-pin connector which directly fits the AM437x IDK. An example firmware for Sitara AM437x IDK is provided, which outputs the measured angle from the Sin/Cos encoder with up to 28-bit resolution through the Sitara’s USB virtual COM port.
• Offline AC/DC 75W Quasi-Resonant Flyback Converter Reference Design - PMP10100 - TI Tool Folder
  PMP10100?SYS-null-null-findchips-refdes-rd-null-wwe: The PMP10100 reference design uses the LM5023 flyback controller for the Quasi-Resonant Flyback Topology. It generates an isolated output (19.5V@3.84A) from an universal input (85VAC - 265VAC).
• Dual-Stage Triple-Output Buck Converter - PMP7800.1 - TI Tool Folder
  PMP7800: The PMP7800.1 reference design is a Buck which uses a LMR14203 and was intended for Computers and Peripherals applications. It can generate a Non-Isolated 3.3 volt output at 0.07 Amps from an input 21.6 to 26.4 Volts DC.
• Dual Output Rail Power Supply with Inverting Buck Boost Converter Reference Design
  PMP10090.2: PMP10090.2 shows a power supply, which provides a positive and a negative voltage rail in an inverting Buck Boost configuration. A 12V input is converted to 15V and -15V output voltages with 700mA load current each.
• 20W SEPIC Low-Cost Lead Acid Battery Charger Reference Design - PMP10081 - TI Tool Folder
  PMP10081?SYS-null-null-findchips-refdes-rd-null-wwe: The PMP10081 reference design shows a simple and low-cost solution of a lead acid battery charger. The input voltage range is from 9V to 36V and the maximum output voltage is 13.8V, which is sufficient for a six-cell lead acid battery with a charge current up to 1.5A.
• Wide Vin, 3A Buck 2-Layer Reference Design for Automotive Cluster with CISPR 25 Class 5 Compliance
  PMP10735: The PMP10735 reference design is a 5V, 3A output power supply in a 2-layer board design for off-battery automotive instrument cluster applications. The reference board has an input EMI filter and optmized layout for improved EMI performance.
• Shunt based Ground Fault Protection for Inverters Powered from 220Vac Supply Reference Design
  TIDA-00442: The TIDA-00442 TI design provides a reference solution for detecting ground fault in inverter based drives. Inverter current is measured on both DC positive and DC negative bus using shunt resistors. Current on DC positive bus is measured using INA170 which is powered by low side switched buck converter. Current on DC negative bus is sensed using precision opamp’s. The difference between the two measured currents is compared against a fixed threshold to determine the ground fault condition using high speed comparators.
• Two-switch buck-boost converter with 28.0V @ 2.5A and an input voltage range of 10..32V - PMP8570 - TI Tool Folder
  PMP8570?SYS-null-null-findchips-refdes-rd-null-wwe: This design is a two-switch buck boost converter which generates an output voltage of 28.0V @ 2.5A from an input voltage range of 10..32V.
• Single-Channel Industrial Voltage & Current Output Driver, Isolated, EMC/EMI Tested Reference Design - TIPD153 - TI Tool Folder
  TIPD153?SYS-null-null-findchips-refdes-rd-null-wwe: This TI CerTIfied Reference Design implements a isolated single-channel industrial voltage and current output module using the DAC8760 and ISO7641. The circuit features a digitally controlled voltage or current output that produces the standard outputs of 0-20mA, 0-24mA, 4-20mA, 0-5V, +/-5V, 0-10V and +/-10V outputs based on the internal register settings of the DAC8760. The design includes the required external protection circuitry needed to pass the IEC61000-4-2/3/4/6 tests and IEC61000-4 test results are included. The protection circuitry does not negatively affect the voltage or current output performance resulting in <0.1% total unadjusted error (TUE) for both outputs.
• RS-485 Interface with Integrated 1.8V Level-Shift Capability
  TIDA-00193: This circuit demonstrates the implementation of a low power, RS-485 transceiver with selectable data rate and flexible I/O logic levels. A dual-output LDO allows for operation with either 1.8V or 3.3V interface logic levels. A slew rate selection pin allows for driver slew rate control, enabling low-speed data transmission (250kbps) over long distances, or high-speed data transmission (20Mbps) over shorter bus lengths.
• Small Form-Factor Reinforced Isolated IGBT Gate Drive Reference Design for 3 Phase Inverter
  TIDA-00446: The TIDA-00446 reference design consists of six reinforced isolated IGBT gate drivers along with dedicated gate drive power supplies. This compact reference design is intended to control IGBT’s in 3-phase inverters like AC drives, uninterruptible power supplies (UPS) and solar inverters. The design uses a reinforced isolated IGBT gate driver with DESAT feature and built-in miller clamp protection, enabling use of unipolar supply voltage for the gate drive. Open loop push pull topology based power supply for each gate driver provides flexibility in PCB routing. The push pull transformer driver used in TIDA-00446 operates at 420 khz which helps in reducing the size of the isolation transformer leading to compact power supply solution. Gate drive power supply can be disabled to facilitate safe torque off (STO).
• Temperature Sensor Interface Module for Programmable Logic Controllers (PLC) - TIDA-00018 - TI Tool Folder
  TIDA-00018?SYS-null-null-findchips-refdes-rd-null-wwe: The TIDA-00018 reference design enables faster development of high precision temperature measurement solutions using 24-Bit delta-sigma ADC and most widely used temperature sensors like thermocouple and RTD. The design guide will address the sensor signal conditioning, thermocouple cold junction compensation, ratiometric measurement technique for RTD, recommended software flow, sensor linearization, sensor diagnostics, transient protection, PCB layout and other practical design considerations for achieving high precision robust design for temperature measurement in industrial applications. The Temperature Sensor Interface Module is a fully isolated design, which is essential for small sensor signal measurement. The heart of this reference design is a 24-Bit delta-sigma ADC that provides a high resolution, high integration, low noise, and low cost complete sensor analog front-end (AFE) for DC sensing applications. This ADC also makes it suitable to interface with different types of sensors, thus saving board space, reducing design efforts, decreasing the time to market, and lower BOM cost. Furthermore, external protection circuitry has been successfully tested for compliance with regulatory IEC61000-4 EFT, ESD, and surge standards. Compliance to IEC61000-4 is necessary to ensure that the design not only survives but also perform as intended in the harsh/noisy industrial environment.
• EMI Optimized 2-layer 15W Power Supply for Automotive with CISPR 25 Class 5 Compliance - PMP10604 - TI Tool Folder
  PMP10604?SYS-null-null-findchips-refdes-rd-null-wwe: The PMP10604 reference design is a 2-layer board 5V, 3A output power supply using LM53603 buck regulator for cluster unit in automotive applications. The LM53603 is a 3.5V to 36V input, 3A output capable, and 2.1 MHz fixed frequency buck regulator, specially designed for automotive applications. It has exceptionally low quiescent current (24µA typical at no load), and can transit to PFM from PWM to ensure high efficiency at light load. For this reference design, it has an input voltage range of 7.5V to 36V, covering the wide variation conditions of the 12V battery in automotive space. The reference board includes an input EMI filter section, and the layout is optimized for improved EMI performance on a 2-layers PCB. The board was tested under the automotive EMC standard, CISPR 25, and the conducted emissions were in compliance with the CISPR 25 Class 5 requirements.
• Multi-output Multi-buck 20W Power Supply for Xilinx Zynq FPGA Applications Reference Design
  PMP9335.2: PMP9335 is designed for Xilinx Zynq FPGA applications utilizing the TPS84A20 and TPS84320. This design uses an external timer to synchronize the switching frequency to 300 kHz. It also employs a controlled power up and power down sequence.
• ±12V/700mA Dual Power Supply Reference Design
  PMP10088.1: PMP10088.1 is a reference design which provides a dual output +12V and -12V from an industrial input voltage of 24V.
• Evaluation Module (EM) Adaptor
  TIDM-LPBP-EMADAPTER: This BoosterPack kit contains one "EM Adapter BoosterPack". The purpose of the EM adapter board is to provide an-easy-to-use bridge between any of the TI MCU LaunchPads and the vide variety of TI RF evaluation modules (EM), for instance the CCxxxx Low-Power RF evaluation modules. No specific software is provided, so it is up to the user to write the appropriate code to interconnect the MCU with the RF device.
• LM3445 – 220VAC, 7W Dimmable Isolated - PMP7751 - TI Tool Folder
  PMP7751?SYS-null-null-findchips-refdes-rd-null-wwe: This demonstration board highlights the performance of a LM3445 based Flyback LED driver solution that can be used to power a single LED string consisting of 6 / 7 series connected LEDs from an 198 VRMS to 264 VRMS, 50 Hz input power supply. This is a two-layer board using the bottom and top layer for component placement. The demonstration board can be modified to adjust the LED forward current, the number of series connected LEDs that are driven and the switching frequency. Refer to the LM3445 datasheet for detailed instructions. A bill of materials is included that describes the parts used on this demonstration board.
• RS-485 Interface with Integrated 1.8V Level-Shift Capability - TIDA-00193 - TI Tool Folder
  TIDA-00193?SYS-null-null-findchips-refdes-rd-null-wwe: This circuit demonstrates the implementation of a low power, RS-485 transceiver with selectable data rate and flexible I/O logic levels. A dual-output LDO allows for operation with either 1.8V or 3.3V interface logic levels. A slew rate selection pin allows for driver slew rate control, enabling low-speed data transmission (250kbps) over long distances, or high-speed data transmission (20Mbps) over shorter bus lengths.
• Multi-output Multi-buck 20W Power Supply for Xilinx Zynq FPGA Applications Reference Design - PMP9335.2 - TI Tool Folder
  PMP9335: PMP9335 is designed for Xilinx Zynq FPGA applications utilizing the TPS84A20 and TPS84320. This design uses an external timer to synchronize the switching frequency to 300 kHz. It also employs a controlled power up and power down sequence.
• Isolated Auto-Polarity RS-485 Transceiver Reference Design - TIDA-00263 - TI Tool Folder
  TIDA-00263?SYS-null-null-findchips-refdes-rd-null-wwe: This reference design demonstrates an isolated RS-485 bus node with automatic correction of a reversed bus signal polarity caused by cross-wire faults. The design provides transient protection protecting the signal path against ESD, EFT, and surge transients specified in the IEC 61000 family of transient immunity standards. An isolated DC-DC converter provides power supply across the isolation barrier utilizing the push-pull converter principle.
• Temperature Sensor Interface Module for Programmable Logic Controllers (PLC)
  TIDA-00018: The TIDA-00018 reference design enables faster development of high precision temperature measurement solutions using 24-Bit delta-sigma ADC and most widely used temperature sensors like thermocouple and RTD. The design guide will address the sensor signal conditioning, thermocouple cold junction compensation, ratiometric measurement technique for RTD, recommended software flow, sensor linearization, sensor diagnostics, transient protection, PCB layout and other practical design considerations for achieving high precision robust design for temperature measurement in industrial applications. The Temperature Sensor Interface Module is a fully isolated design, which is essential for small sensor signal measurement. The heart of this reference design is a 24-Bit delta-sigma ADC that provides a high resolution, high integration, low noise, and low cost complete sensor analog front-end (AFE) for DC sensing applications. This ADC also makes it suitable to interface with different types of sensors, thus saving board space, reducing design efforts, decreasing the time to market, and lower BOM cost. Furthermore, external protection circuitry has been successfully tested for compliance with regulatory IEC61000-4 EFT, ESD, and surge standards. Compliance to IEC61000-4 is necessary to ensure that the design not only survives but also perform as intended in the harsh/noisy industrial environment.
• Two-switch buck-boost converter with 28.0V @ 2.5A and an input voltage range of 10..32V
  PMP8570: This design is a two-switch buck boost converter which generates an output voltage of 28.0V @ 2.5A from an input voltage range of 10..32V.
• Space Optimized Wide Vin Triple-Output Power Module Reference Design - TIDA-00783.1 - TI Tool Folder
  TIDA-00783: The TIDA-00783.1 reference design is a triple output wide Vin power module design. It provides 3.3V, 1.8V and 1.2V output, at 6W total power. The layout is optimized for space constrained applications.
• Two-Wire Interface to a HIPERFACE DSL Encoder Reference Design - TIDA-00177 - TI Tool Folder
  TIDA-00177?SYS-null-null-findchips-refdes-rd-null-wwe: The TIDA-00177 reference design is an EMC compliant industrial interface to a two-wire HIPERFACE DSL encoder. Applications include industrial servo drives. The design features a 3.3-V supply RS485 transceiver and line termination and coupling for encoder power over RS485 as per HIPERFACE DSL specification. The design has been tested up to 100m cable length with an integrated cable, where the encoder’s two-wire twisted pair was integrated in the same motor cable. The encoder connector output is protected against over-voltage and short circuit to prevent damage to an encoder or during a cable short. The design features an industrial compliant 24-V input with wide range from 18-36V. A 3.3V I/O connector with logic signals for easy interface to a host processor with HIPERFACE DSL Master IP Core is made available.
• 9 to 60Vin 12Vout @ 5A Single-Phase Isolated Synchronous Flyback Converter Reference Design - PMP9256 - TI Tool Folder
  PMP9256?SYS-null-null-findchips-refdes-rd-null-wwe: PMP9256 is an isolated synchronous flyback converter utilizing the LM5122 for industrial applications. The benefit of using a synchronous flyback is higher efficiency compared to a non-synchronous flyback.
• Multi-output Multi-buck 20W Power Supply for Xilinx Zynq FPGA Applications Reference Design
  PMP9335.1: PMP9335 is designed for Xilinx Zynq FPGA applications utilizing the TPS84A20 and TPS84320. This design uses an external timer to synchronize the switching frequency to 300 kHz. It also employs a controlled power up and power down sequence.
• Dual Boost with +15V@300mA and -15V@300mA Output Reference Design - PMP10091.1 - TI Tool Folder
  PMP10091: This reference design provides positive and negative output of 15V.
• Two-Channel Source/Sink Combined Voltage & Current Output, Isolated, EMC/EMI Tested Reference Design - TIPD155 - TI Tool Folder
  TIPD155?SYS-null-null-findchips-refdes-rd-null-wwe: This TI CerTIfied Reference Design implements a two channel combined voltage and current analog output module. The two outputs are independent and can both source and sink voltage and current over the standard industrial output ranges. While the design has been characterized with outputs of ±10 V and ±24 mA, output ranges of 0-5 V, 0-10 V, ±5 V, ±10 V.4-20 mA, 0-20 mA, 0-24 mA, ±20 mA, ±24 mA are possible by adjusting external resistor values. The design includes the necessary external protection elements required to pass the IEC61000-4-2/3/4/5/6 tests along with the measured test data. The protection circuitry does not negatively affect the design and test results showed typical unadjusted errors were <0.1% of the full-scale range (FSR) and calibrated errors were less than 0.01% FSR.
• LM3448 – 220VAC, 8W Dimmable Isolated - PMP8001 - TI Tool Folder
  PMP8001?SYS-null-null-findchips-refdes-rd-null-wwe: This demonstration board highlights the performance of a LM3448 based Flyback LED driver solution that can be used to power a single LED string consisting of 6 / 7 series connected LEDs from an 198 VRMS to 264 VRMS, 50 Hz input power supply. The integrated high-voltage and low Rdson MOSFET reduces design complexity while improving LED driver efficiency. This is a two-layer board using the bottom and top layer for component placement. The demonstration board can be modified to adjust the LED forward current, the number of series connected LEDs that are driven and the switching frequency. Refer to the LM3448 datasheet for detailed instructions. A bill of materials is included that describes the parts used on this demonstration board
• 2.2MHz Switching, Synchronous Split Supply Reference Design for 12V Battery with all Protections - PMP10651.2 - TI Tool Folder
  PMP10651: PMP10651 is a low noise, multi-output SMPS design where LM53603 is used in Inverting Buck-Boost Fly buck topology to generate positive and negative supply needed in multiple noise sensitive applications such as powering High Speed Video Amplifier, RF amplifier, Precision Low noise amplifier etc. The design accepts an input voltage of 7Vin to 15 Vin DC (from 12V Lead Acid Battery) and provides outputs of +12V@500mA, -12v@500mA, 5V @400mA and 3.3V@150mA. It features a small size and is an inexpensive and more efficient solution to using Flyback or Pushpull converters .
• ±12V/700mA Dual Power Supply Reference Design - PMP10088.1 - TI Tool Folder
  PMP10088: PMP10088.1 is a reference design which provides a dual output +12V and -12V from an industrial input voltage of 24V.
• Automotive Acoustic Knock Sensor Interface - TIDA-00152 - TI Tool Folder
  TIDA-00152?SYS-null-null-findchips-refdes-rd-null-wwe: This TIDA-00152 reference design utilizes a dual-channel, signal processing IC for detection of premature detonation in combustion (gasoline) engines. The heart of this design is the TPIC8101 that serves as an interface between acoustical sensors or accelerometers and automobile engine management systems. Programmable features on this device include the selection of engine knock detection sensitivity, engine resonance frequency, and sampling rate control of on-board ADC and DAC in signal processing chain. These features allow the TPIC8101 to be a flexible interface that can adapt to cost and/or processing time constraints of the customer.
• Evaluation Module (EM) Adaptor - TIDM-LPBP-EMADAPTER - TI Tool Folder
  TIDM-LPBP-EMADAPTER?SYS-null-null-findchips-refdes-rd-null-wwe: This BoosterPack kit contains one "EM Adapter BoosterPack". The purpose of the EM adapter board is to provide an-easy-to-use bridge between any of the TI MCU LaunchPads and the vide variety of TI RF evaluation modules (EM), for instance the CCxxxx Low-Power RF evaluation modules. No specific software is provided, so it is up to the user to write the appropriate code to interconnect the MCU with the RF device.
• TPS92310 Universal 18W - PMP8006 - TI Tool Folder
  PMP8006?SYS-null-null-findchips-refdes-rd-null-wwe: The main purpose of this reference design is to demonstrate a high efficiency offline LED driver with PFC based on TPS92310. This LED driver is designed for converting an AC input to a regulated LED current.The operating conditions and performance of the reference design are as follows: 1.90VAC to 264VAC, 60/50HZ Input voltage;2.55V to 65V LED Forward Voltage;3.275mA Regulated LED Current;4.System Efficiency ≥ 90%;5.High Power Factor > 0.9;6.Output Short-Circuit and Open-Circuit Protection.
• Automotive Buck Converter 3.3V @ 500mA Reference Design
  PMP8637.2: This design is a buck converter for automotive applications covering an input voltage range of 3.5V .. 35V. It provides an output voltage of 3.3V @ 600mA.
• Automotive Buck-boost Converter Providing 8V @ 1.5A Reference Design - PMP8635 - TI Tool Folder
  PMP8635?SYS-null-null-findchips-refdes-rd-null-wwe: This design is a buck-boost converter for automotive applications covering an input voltage range of 2..20V. It provides an output voltage of 8.0V @ 1.5A continuous / 2.5A peak.
• Automotive Buck-boost Converter Providing 5.7V @ 1.2A Reference Design
  PMP8637.1: This design is a buck-boost converter for automotive applications covering an input voltage range of 3.5 .. 35V. It provides an output voltage of 5.7V @ 1.2A.
• Automotive Camera Module Reference Design for Uncompressed Digital Video With Wide Vin Front End - PMP10653.1 - TI Tool Folder
  PMP10653: PMP10653.1 is an Optimized Automotive Camera Module Design for Uncompressed Digital Video over Coax cable. The design is broadly divided into four Blocks.
• Dual-channel XAUI to SFI Reference Design for Systems with Two or More SFP+ Optical Ports - TIDA-00234 - TI Tool Folder
  TIDA-00234?SYS-null-null-findchips-refdes-rd-null-wwe: The TIDA-00234 XAUI to SFI reference design is intended for Enterprise and Service Provider Networking applications like Ethernet Switches and Routers that implement multiple 10G Ethernet compliant Optical (SFP+) ports. This reference design features the TLK10232 device which is the most compact Dual-channel XAUI-to-SFI Transceiver with the lowest power consumption in its category. This reference design allows access to the high-speed signals (up to 10Gbps) generated by the TLK10232 via SMA connectors or an SFP+ Module via the SFP+ optical module cage. Also, featured is the CDCM6208 device that can provide extremely low-jitter Clock input to the TLK10232 in customer systems that do not have one available (or does not meet the jitter requirement of the system).
• LM3445 – 220VAC, 7W Dimmable Isolated
  PMP7751: This demonstration board highlights the performance of a LM3445 based Flyback LED driver solution that can be used to power a single LED string consisting of 6 / 7 series connected LEDs from an 198 VRMS to 264 VRMS, 50 Hz input power supply. This is a two-layer board using the bottom and top layer for component placement. The demonstration board can be modified to adjust the LED forward current, the number of series connected LEDs that are driven and the switching frequency. Refer to the LM3445 datasheet for detailed instructions. A bill of materials is included that describes the parts used on this demonstration board.
• 2.2MHz Switching, Synchronous Split Supply Reference Design for 12V Battery with all Protections - PMP10651.4 - TI Tool Folder
  PMP10651: PMP10651 is a low noise, multi-output SMPS design where LM53603 is used in Inverting Buck-Boost Fly buck topology to generate positive and negative supply needed in multiple noise sensitive applications such as powering High Speed Video Amplifier, RF amplifier, Precision Low noise amplifier etc. The design accepts an input voltage of 7Vin to 15 Vin DC (from 12V Lead Acid Battery) and provides outputs of +12V@500mA, -12v@500mA, 5V @400mA and 3.3V@150mA. It features a small size and is an inexpensive and more efficient solution to using Flyback or Pushpull converters .
• Space Optimized Wide Vin Triple-Output Power Module Reference Design
  TIDA-00783.3: The TIDA-00783.3 reference design is a triple output wide Vin power module design. It provides 3.3V, 1.8V and 1.2V output, at 6W total power. The layout is optimized for space constrained applications.
• Dual Isolated Half-Duplex RS-485 Repeater Reference Design - TIDA-00333 - TI Tool Folder
  TIDA-00333?SYS-null-null-findchips-refdes-rd-null-wwe: This reference design demonstrates a dual isolated, half-duplex repeater with data rate independent flow-control for long-haul RS-485 networks suitable for industrial applications. The design provides transient protection protecting the signal path against ESD, EFT, and surge transients specified in the IEC 61000 family of transient immunity standards.
• 100-240VAC Input, 60W, 2-string, PWM Dimmable LED Driver Reference Design
  PMP6024: PMP6024 is an offline, LED driver circuit consisting of an isolated, power-factor corrected, constant output voltage flyback converter followed by two DC/DC buck LED current controllers. It is suitable for indoor or outdoor area lighting applications of 3500-5000 lumens (depending upon LED selection). LED brightness is controlled by a 3.3V, 10kHz PWM signal which is converted to a DC level adjustment of the LED string currents avoiding PWM modulation of the light output.
• Dual Output Rail Power Supply with Inverting Buck Boost Converter Reference Design - PMP10090.1 - TI Tool Folder
  PMP10090: PMP10090.1 shows a power supply, which provides a positive and a negative voltage rail in an inverting Buck Boost configuration. A 12V input is converted to 15V and -15V output voltages with 700mA load current each.
• Two-Channel Source/Sink Combined Voltage & Current Output, Isolated, EMC/EMI Tested Reference Design
  TIPD155: This TI CerTIfied Reference Design implements a two channel combined voltage and current analog output module. The two outputs are independent and can both source and sink voltage and current over the standard industrial output ranges. While the design has been characterized with outputs of ±10 V and ±24 mA, output ranges of 0-5 V, 0-10 V, ±5 V, ±10 V.4-20 mA, 0-20 mA, 0-24 mA, ±20 mA, ±24 mA are possible by adjusting external resistor values. The design includes the necessary external protection elements required to pass the IEC61000-4-2/3/4/5/6 tests along with the measured test data. The protection circuitry does not negatively affect the design and test results showed typical unadjusted errors were <0.1% of the full-scale range (FSR) and calibrated errors were less than 0.01% FSR.
• Dual Output Rail Power Supply with Inverting Buck Boost Converter Reference Design - PMP10090.2 - TI Tool Folder
  PMP10090: PMP10090.2 shows a power supply, which provides a positive and a negative voltage rail in an inverting Buck Boost configuration. A 12V input is converted to 15V and -15V output voltages with 700mA load current each.
• EMI Optimized 2-layer 15W Power Supply for Automotive with CISPR 25 Class 5 Compliance
  PMP10604: The PMP10604 reference design is a 2-layer board 5V, 3A output power supply using LM53603 buck regulator for cluster unit in automotive applications. The LM53603 is a 3.5V to 36V input, 3A output capable, and 2.1 MHz fixed frequency buck regulator, specially designed for automotive applications. It has exceptionally low quiescent current (24µA typical at no load), and can transit to PFM from PWM to ensure high efficiency at light load. For this reference design, it has an input voltage range of 7.5V to 36V, covering the wide variation conditions of the 12V battery in automotive space. The reference board includes an input EMI filter section, and the layout is optimized for improved EMI performance on a 2-layers PCB. The board was tested under the automotive EMC standard, CISPR 25, and the conducted emissions were in compliance with the CISPR 25 Class 5 requirements.
• Interface to a Sin/Cos Encoder with Sitara AM437x Reference Design - TIDA-00178 - TI Tool Folder
  TIDA-00178?SYS-null-null-findchips-refdes-rd-null-wwe: The TIDA-00178 reference design is an EMC compliant industrial interface to Sin/Cos position encoders. Applications include industrial drives, which require accurate speed and position control. The design utilizes a 16-bit dual sample ADC with drop-in compatible 14- or 12-bit versions available, allowing for optimization of performance and cost. TIDA-00178 provides a direct connection to Sitara AM437x using SPI and QEP. For quick evaluation it features a 60-pin connector which directly fits the AM437x IDK. An example firmware for Sitara AM437x IDK is provided, which outputs the measured angle from the Sin/Cos encoder with up to 28-bit resolution through the Sitara’s USB virtual COM port.
• Non-Isolated Synchronous Buck used for Transportation and Automotive Applications - PMP7858 - TI Tool Folder
  PMP7858?SYS-null-null-findchips-refdes-rd-null-wwe: This is a synchronous buck converter with an input voltage range of 8V-to-16Vin (40Vin max) and a regulated output at 5Vout @ 1.5A.
• 6.5V/2A Boost Converter Reference Design - PMP10026 - TI Tool Folder
  PMP10026?SYS-null-null-findchips-refdes-rd-null-wwe: This reference design provides an output voltage of 6.5V from an input voltage range of 3V to 6.5V.
• 5W WPC (Qi) Compliant Wireless Power Transmitter for 5V Applications Reference Design - TIDA-00259 - TI Tool Folder
  TIDA-00259?SYS-null-null-findchips-refdes-rd-null-wwe: This reference design showcases the bq500212A in a 5W WPC (Qi) compliant wireless power transmitter for 5V applications. The transmitter circuits are laid out in a 50mm X 50mm configuration which matches the dimensions for WPC Type A11 TX Coil. The design is Qi certified and has been certified to WPC v1.1 standard.
• Triac Dimmable AC-DC LED Driver Reference Design
  PMP6013: This reference design provides a high-brightness LED driver based on the TPS92310 configured as a power factor corrected flyback regulator that is triac dimmable. It is designed to operate with an input voltage in the range of 90VAC to 135VAC with a 120VAC nominal input voltage. This design is set up for a default output current of 340mA with an output voltage range of 21V to 27V or approximately 6 to 8 LEDs depending on the forward voltage of each.
• Multi-Cell Battery Manager Unit with Integrated Charging, Gauging, Authentication and Protection - TIDA-00553 - TI Tool Folder
  TIDA-00553?SYS-null-null-findchips-refdes-rd-null-wwe: The Texas Instruments bq40z60 device is a Battery Pack Manager that integrates battery charging control output, gas gauging, and protection for completely autonomous operation of 2-series to 4-series cell Li-Ion and Li-Polymer battery packs. The architecture enables internal communication between the fuel gauging processor and battery charger controller to optimize the charging profile based on the external load conditions and power path source management during load transients and adaptor current limitations in the system. The charging current efficiency is scalable for power transfer based on the external components, such as the NFETs, inductor, and sensing resistor.
• AC-mains LED Lighting with DALI DMX512 & Power Line Communications Reference Design - TIDM-AC-LED-COM - TI Tool Folder
  TIDM-AC-LED-COM?SYS-null-null-findchips-refdes-rd-null-wwe: Ideal for outdoor, entertainment, and industrial lighting applications, this LED Lighting design provides high power and high efficiency illumination with built-in communications networking. The lighting unit consists of a 250W universal AC-input LED driver power supply and a demonstrational six-string LED lamp. Driving the LED’s with great power efficiency and electrical utilization, the LED driver power supply operates at greater than 90% power efficiency with 0.99 power factor (PF). Furthermore, to support system-networked lighting and remote connectivity, this power supply includes support for common lighting communications standards including Digital Addressable Lighting Interface (DALI), DMX512, and Power Line Communications (PLC).
• Single cell Li-Ion/Li Polymer Battery protection IC Reference Design
  TIDA-00265: The bq297xy device provides the protection functions for Li-Ion/Li-Polymer cells, and monitors across the external power FETs for protection due to high charge or discharge currents. In addition, there is overcharge and depleted battery monitoring and protection. These features are implemented with low current consumption in NORMAL mode operation.
• Analog Input Module for Industrial Outputs and Temperature Sensors Reference Design
  TIPD164: This TI Designs, Precision Verified design implements an analog input module for industrial voltages, currents, and temperature sensors. For industrial outputs, the possible input ranges include: 4-20 mA, 0-20 mA, +/-25 mA, 0-5 V, 0-10 V, +/-5 V, +/-10 V. The design includes conditioning and level-shift circuitry which converts the large industrial outputs into a proper input range for a +5V delta-sigma ADC. The ADC has features to directly acquire information from the RTD and thermocouple sensors over their full temperature range.
• Dual-Stage Triple-Output Buck Converter - PMP7800.3 - TI Tool Folder
  PMP7800: The PMP7800.3 reference design is a Buck which uses a LMR14203 and was intended for Computers and Peripherals applications. It can generate a Non-Isolated 1.8 volt output at 0.23 Amps from an input 21.6 to 26.4 Volts DC.
• Wide Vin, 3A Buck 2-Layer Reference Design for Automotive Cluster with CISPR 25 Class 5 Compliance - PMP10735 - TI Tool Folder
  PMP10735?SYS-null-null-findchips-refdes-rd-null-wwe: The PMP10735 reference design is a 5V, 3A output power supply in a 2-layer board design for off-battery automotive instrument cluster applications. The reference board has an input EMI filter and optmized layout for improved EMI performance.
• Automotive Camera Module Reference Design for Uncompressed Digital Video With Wide Vin Front End - PMP10653.3 - TI Tool Folder
  PMP10653: PMP10653.3 is an Optimized Automotive Camera Module Design for Uncompressed Digital Video over Coax cable. The design is broadly divided into four Blocks.
• Low-Power Reference and Bipolar Voltage Conditioning Circuit Reference Design for Low-Power ADCs
  TIPD154: This TI Precision Verified Design provides the theory, component selection, and simulation for a single-supply, low-power signal conditioning circuit designed to translate a +/-5 V input signal to the proper input range of a single-supply low-power 16-Bit ΔΣ ADC such as the one inside the MSP430 or other similar single-supply ADCs. A zero-drift op amp was selected to provide excellent dc performance in the attenuation and level-shifting circuit. Two low-power reference circuits are used to provide power, the ADC reference voltage, and biasing to the input conditioning circuit.
• 5W WPC (Qi) Compliant Wireless Power Transmitter for 5V Applications Reference Design
  TIDA-00259: This reference design showcases the bq500212A in a 5W WPC (Qi) compliant wireless power transmitter for 5V applications. The transmitter circuits are laid out in a 50mm X 50mm configuration which matches the dimensions for WPC Type A11 TX Coil. The design is Qi certified and has been certified to WPC v1.1 standard.
• Small Form-Factor Reinforced Isolated IGBT Gate Drive Reference Design for 3 Phase Inverter - TIDA-00446 - TI Tool Folder
  TIDA-00446?SYS-null-null-findchips-refdes-rd-null-wwe: The TIDA-00446 reference design consists of six reinforced isolated IGBT gate drivers along with dedicated gate drive power supplies. This compact reference design is intended to control IGBT’s in 3-phase inverters like AC drives, uninterruptible power supplies (UPS) and solar inverters. The design uses a reinforced isolated IGBT gate driver with DESAT feature and built-in miller clamp protection, enabling use of unipolar supply voltage for the gate drive. Open loop push pull topology based power supply for each gate driver provides flexibility in PCB routing. The push pull transformer driver used in TIDA-00446 operates at 420 khz which helps in reducing the size of the isolation transformer leading to compact power supply solution. Gate drive power supply can be disabled to facilitate safe torque off (STO).
• 9 to 60Vin 12Vout @ 5A Single-Phase Isolated Synchronous Flyback Converter Reference Design
  PMP9256: PMP9256 is an isolated synchronous flyback converter utilizing the LM5122 for industrial applications. The benefit of using a synchronous flyback is higher efficiency compared to a non-synchronous flyback.
• Two-Wire Interface to a HIPERFACE DSL Encoder Reference Design
  TIDA-00177: The TIDA-00177 reference design is an EMC compliant industrial interface to a two-wire HIPERFACE DSL encoder. Applications include industrial servo drives. The design features a 3.3-V supply RS485 transceiver and line termination and coupling for encoder power over RS485 as per HIPERFACE DSL specification. The design has been tested up to 100m cable length with an integrated cable, where the encoder’s two-wire twisted pair was integrated in the same motor cable. The encoder connector output is protected against over-voltage and short circuit to prevent damage to an encoder or during a cable short. The design features an industrial compliant 24-V input with wide range from 18-36V. A 3.3V I/O connector with logic signals for easy interface to a host processor with HIPERFACE DSL Master IP Core is made available.
• IEC ESD, EFT, and Surge Protected RS-485 Reference Design
  TIDA-00731: The TIDA-00731 is a reference design examining how to protect an RS-485 bus against lethal transient waveforms such as IEC ESD, IEC EFT, and IEC surge. The reference design shows the level of protection that can be achieved through the implementation of an external protection scheme on the bus lines of a standard RS-485 transcever as well as a RS-485 tranceiver with integrated IEC protection.
• Power Line Communications (PLC) Lite™ Reference Design for Industrial Applications
  TIDM-INDUSTRIAL-PLC: This TI implementation of Power Line Communications (PLC) is a new option for adding communications to industrial equipment such as solar arrays. PLC Lite™ offers higher data throughput than earlier forms of PLC and greater robustness for transmission across noisy electric lines by using OFDM PHY technology. This design is based upon a C2000 controlCARD and an analog front end for PLC. The C2000 MCU executes the entire PLC Lite software stack. TIDM-INDUSTRIAL-PLC achieves up to 21 kbps data rates across AC or DC power lines compared to traditional SFSK PLC solutions (2-5 kbps) all while decreasing the overall BOM cost of a typical PLC modem.
• Multi-Cell Battery Manager Unit with Integrated Charging, Gauging, Authentication and Protection
  TIDA-00553: The Texas Instruments bq40z60 device is a Battery Pack Manager that integrates battery charging control output, gas gauging, and protection for completely autonomous operation of 2-series to 4-series cell Li-Ion and Li-Polymer battery packs. The architecture enables internal communication between the fuel gauging processor and battery charger controller to optimize the charging profile based on the external load conditions and power path source management during load transients and adaptor current limitations in the system. The charging current efficiency is scalable for power transfer based on the external components, such as the NFETs, inductor, and sensing resistor.
• Fluxgate Based Displacement Sensor Reference Design - TIDA-00463 - TI Tool Folder
  TIDA-00463?SYS-null-null-findchips-refdes-rd-null-wwe: The TIDA-00463 showcases a displacement sensor for linear distance measurements in a BoosterPack form factor for TI LaunchPad. The design is suitable for any application where a distance measurement, even through non-magnetic materials, is needed and non-contact, wear-free measurements are required. Through the use of magnetic fluxgate technology, this design is able to cover a wide measurement distance while achieving high resolution and accuracy.
• Shunt based Ground Fault Protection for Inverters Powered from 220Vac Supply Reference Design - TIDA-00442 - TI Tool Folder
  TIDA-00442?SYS-null-null-findchips-refdes-rd-null-wwe: The TIDA-00442 TI design provides a reference solution for detecting ground fault in inverter based drives. Inverter current is measured on both DC positive and DC negative bus using shunt resistors. Current on DC positive bus is measured using INA170 which is powered by low side switched buck converter. Current on DC negative bus is sensed using precision opamp’s. The difference between the two measured currents is compared against a fixed threshold to determine the ground fault condition using high speed comparators.
• Automotive Camera Module Reference Design for Uncompressed Digital Video With Wide Vin Front End
  PMP10653.2: PMP10653.2 is an Optimized Automotive Camera Module Design for Uncompressed Digital Video over Coax cable. The design is broadly divided into four Blocks.
• DisplayPort Video 4:1 Aggregation Reference Design - TIDA-00309 - TI Tool Folder
  TIDA-00309?SYS-null-null-findchips-refdes-rd-null-wwe: This verified reference design is a complete four channel DisplayPort aggregation and de-aggregation solution. One TLK10022 is used to aggregate four synchronous DisplayPort (DP) sources together into one 10.8 Gbps serial link. The serial data is transferred via copper or optical fiber where a second TLK10022 is used to de-aggregate and seamlessly redisplay the original video content.
• 60Vin 12Vout @ 4A Buck Reference Design - PMP9333 - TI Tool Folder
  PMP9333?SYS-null-null-findchips-refdes-rd-null-wwe: The circuit has an operating input voltage range of 50V to 60V max. The output is set at 12V at 4A continuous, with a 7A peak transient.