Details for: es1d

Total stock available through FindChips: 1,971,399
No results were found.
ES1D
DIODE 1 A, 200 V, SILICON, SIGNAL DIODE, DO-214AC, SMAJ, 2 PIN, Signal Diode

Reference Designs

  • Isolated LED Driver with PFC for A19 Lamp Application using LM3447
    230VAC, 36VLED 12W: The main purpose of this reference design is to demonstrate the LM3447 is ideal for implementing high dimmable performance with single stage PFC, isolated LED lamp drivers where simplicity, low-component count and small solution size. The operating conditions and performance of the reference design are as follows: 190VAC to 264VAC, 50Hz Input Voltage, 32V to 38V LED Voltage, 280mA Regulated LED Current, > 81% Typical System Efficiency, High Power Factor > 0.
  • Laser and Ionization Unit
    PMP2534: The PMP2534 is composed of two times active clamp forward, delivering 0...35V@10Amax, two current limit functions to protect the 3.3V and 5V outputs and some interface for a microcntroller. The active clamps are constant voltage and/or constant current controllable by means of two PWM inputs. This power supply is suitable as general bench power generator from a desktop standard PSU as source.
  • High voltage isolated DC/DC converter with 30 to 800V input and 24V @ 250mA output
    PMP7763: PMP7763 is a high voltage isolated DC/DC flyback converter. The input range is 30...800V and output is 24V @ 250mA. It has a high voltage hold off circuit. The secondary is open loop with no feedback control for the output. However, there is feedback control for the primary.
  • 18Vdc-54Vdc Input, 24V @ 5A Output, Active Clamp Forward
    PMP4844: The PMP4844 reference design provides an isolated 24V output at 120W from an 18V to 54V telecom input with up to 94% efficiency. This design uses the UCC2897A active clamp controller along with an ISO721 digital isolator and TPS28225 to drive synchronous rectifiers. The circuit is built in an industry standard Half-Brick footprint.
  • Class 3- Mulitple Output, High Efficiency Flyback Converter for PoE Applications
    PMP8408.2: This converter is used for Class 3 PoE applications where high efficiency and multiple outputs are required. The flyback converter with synchronous rectifier provides excellent efficiency and small size for PoE applications such as a IP Phones. The TPS23785B contains both the PoE Powered Device and the PWM controller functions.
  • Class 1: Mulitple Output, High Efficiency Flyback Converter for PoE Applications Reference Design
    PMP8752.1: This converter is used for Class 1 PoE applications where high-efficiency and multiple-outputs are required. The multi-outputs for this design are 3.3V/0.7A, 5V/0.145A, 3.3V/1.5A. The flyback converter with synchronous rectifier provides excellent efficiency, and small size for PoE applications, such as an IP phone solution. The TPS23785B contains both the PoE powered device and the PWM controller functions.
  • Class 3- Mulitple Output, High Efficiency Flyback Converter for PoE Applications
    PMP8454.1: This converter is used for Class 3 PoE applications where high efficiency and multiple outputs are required. PMP8454.1 has an output of 3.3V@2A. The flyback converter with synchronous rectifier provides excellent efficiency and small size for PoE applications such as a IP Phones. The TPS23785B contains both the PoE Powered Device and the PWM controller functions.
  • 18Vdc-36Vdc Input, 28V/100W Active Clamp Forward
    PMP7294: This reference design uses the UCC2897A active clamp controller to generate an isolated 28V/3.6A output from a standard 24Vdc telecom input. This design uses diode rectification on the output stage and achieves efficiencies up to 93%. The output is adjustable down to 24V by changing a single resistor value.
  • Flyback for Audio/Video Control
    PMP2915: This low-power (3W) off-line isolated flyback regulator produces dual +12V/+24V outputs. Output voltage cross-regulation is excellent due to the use of a linear regulator on the 12V output and direct feedback on the 24V output.
  • 36V-75VDC Input, 12V/10A Active Clamp Forward, 1/8th Brick Form Factor
    PMP7451: This reference design generates a 12V/10A output from a standard 48V telecom input. The UCC2897A controls an active clamp forward converter power stage. The low gate charge and low RDSon of the CSD18531Q5A, implemented as self-driven synchronous rectifiers, provide for a highly efficient design. This design is laid out in a standard 1/8th brick footprint and includes enable, remote sense, and output overvoltage features.
  • Isolated auxiliary flyback for telecom applications with 5.0V @ 300mA and 12.0V @ 80mA
    PMP8580: This design is an auxiliary flyback with telecom input range (36..60V) providing two outputs. The two outputs (5.0V @ 300mA and 12.0V @ 80mA) are isolated to the primary side as well as to each other.
  • Non isolated flyback with 30 to 800V input and 20V @ 250mA output
    PMP7764: PMP7764 is a non-isolated flyback converter. The input voltage ranges from 30...800V DC. The output is 20V @ 250mA. It has a high voltage hold off circuit.
  • LM3448-220VAC, 8W Dimmable Isolated
    PMP8001 : This demonstration board highlights the performance of a LM3448 based Flyback LED driver solution that can be used to power a single LED string consisting of 6 / 7 series connected LEDs from an 198 VRMS to 264 VRMS, 50 Hz input power supply. The integrated high-voltage and low Rdson MOSFET reduces design complexity while improving LED driver efficiency. This is a two-layer board using the bottom and top layer for component placement. The demonstration board can be modified to adjust the LED forward current, the number of series connected LEDs that are driven and the switching frequency. Refer to the LM3448 datasheet for detailed instructions.
  • 14V-35V Input, 12V/7A5, 5V/100mA, Active Clamp
    PMP5549 : This Active clamp Forward supplies two outputs, 12V @ 7.5A and 5V @ 100mA, with a LDO, starting from a 14V-35V input source, reaching 94% efficiency with sync. Rectification.
  • Class 1: Mulitple Output, High Efficiency Flyback Converter for PoE Applications
    PMP8752.2 : This converter is used for Class 1 PoE applications where high efficiency and multiple outputs are required. The specific output for PMP8752.2 is 5V@.145A. The flyback converter with synchronous rectifier provides excellent efficiency and small size for PoE applications such as a IP Phones. The TPS23785B contains both the PoE Powered Device and the PWM controller functions.
  • Class 3- Mulitple Output, High Efficiency Flyback Converter for PoE Applications
    PMP8408.1: This converter is used for Class 3 PoE applications where high efficiency and multiple outputs are required. The flyback converter with synchronous rectifier provides excellent efficiency and small size for PoE applications such as a IP Phones. The TPS23785B contains both the PoE Powered Device and the PWM controller functions.
  • Class 3- Mulitple Output, High Efficiency Flyback Converter for PoE Applications
    PMP8454.2 : This converter is used for Class 3 PoE applications where high efficiency and multiple outputs are required. This design has a specific output of 5V@1A. The flyback converter with synchronous rectifier provides excellent efficiency and small size for PoE applications such as a IP Phones. The TPS23785B contains both the PoE Powered Device and the PWM controller functions.
  • 36Vdc-75Vdc Input, 20V @ 4A Output, Active Clamp Forward
    PMP3799: The PMP3799 reference design provides an adjustible 20V output at 4A from a standard 48V telecom input with greater than 93% efficiency. This design uses the UCC2897A active clamp controller along with an ISO721 digital isolator and TPS28225 to drive synchronous rectifiers. The output voltage can be adjusted from 16V to 24V by changing a single resistor value. The circuit is built in an industry standard quarter-brick footprint.
  • LM3445 _ 220VAC, 7W Dimmable Isolated
    PMP7751 : This demonstration board highlights the performance of a LM3445 based Flyback LED driver solution that can be used to power a single LED string consisting of 6 / 7 series connected LEDs from an 198 VRMS to 264 VRMS, 50 Hz input power supply. This is a two-layer board using the bottom and top layer for component placement. The demonstration board can be modified to adjust the LED forward current, the number of series connected LEDs that are driven and the switching frequency. Refer to the LM3445 datasheet for detailed instructions. A bill of materials is included that describes the parts used on this demonstration board.
  • 8V-36V Input 12V/7A; 93% Efficient Active Clamp Forward
    PMP5123: The PMP5123 reference design provides an isolated 12V at 7A from a 8V to 36V input range. This design uses the UCC2897A active clamp controller with self-driven synchronous rectifiers to achieve over 93% efficiency.
  • Class 3- Mulitple Output, High Efficiency Flyback Converter for PoE Applications
    PMP8408.3: This converter is used for Class 3 PoE applications where high efficiency and multiple outputs are required. The flyback converter with synchronous rectifier provides excellent efficiency and small size for PoE applications such as a IP Phones. The TPS23785B contains both the PoE Powered Device and the PWM controller functions.
  • 36V-75VDC Input, 5V/20A Active Clamp Forward, 1/8th Brick Form Factor
    PMP8366: This reference design generates a 5V/20A output from a standard 48V telecom input. The UCC2897A controls an active clamp forward converter power stage. The low gate charge and low RDSon of the CSD17312Q5, implemented as self-driven synchronous rectifiers, provide for a highly efficient design. This design is laid out in a standard 1/8th brick footprint and includes enable, remote sense, and output overvoltage features.
  • 52V-60Vdc Input, 12V/22A Active Clamp Forward
    PMP7376: This reference design generates a 12V/21.7A output from 54V DC input. The UCC2897A controls an active clamp forward converter power stage. The low gate charge and low RDSon of the CSD18531Q5A, implemented as self-driven synchronous rectifiers, allow this design to achieve a max load efficiency of nearly 95%.
  • Class 3- Mulitple Output, High Efficiency Flyback Converter for PoE Applications
    PMP8408: This converter is used for Class 3 PoE applications where high efficiency and multiple outputs are required. The flyback converter with synchronous rectifier provides excellent efficiency and small size for PoE applications such as IP Phones. The TPS23785B contains both the PoE Powered Device and the PWM controller functions.
Show All

Best Price es1d

?

1,971,399 Total stock available through FindChips:

1
975,000
55% Savings:
$.1690
Onlinecomponents.com
$.3794
Average
ECIA (NEDA) Member • Authorized Distributor

World Products

Price $.1690 Stock 4,932 BUY NOW

Price Details es1d

?
Selected Stock: 1
Low Average High
Authorized $.1690 $.2800 $.4270
Independent $.3300 $.4590 $.6000
No listed price
  • These distributors have es1d in stock but do not list price:
  • Distributor Stock